2005 MERCEDES-BENZ SPRINTER oil pressure

RECEIVER/DRIER
DESCRIPTION
The receiver/drier is mounted in a bracket secured
to the left front strut tower in the engine compart-
ment. The receiver/drier is connected between the
front and rear sections of the liquid line between the
condenser outlet and the evaporator inlet. The receiv-
er/drier cannot be repaired. If the receiver/drier is
faulty or damaged, or if the refrigerant system has
been contaminated or left open to the atmosphere for
an indeterminable period or if the compressor has
failed, it must be replaced.
OPERATION
The receiver/drier performs a filtering action to
prevent foreign material in the refrigerant from con-
taminating the expansion valve. A desiccant bag is
mounted inside the receiver/drier canister to absorb
any moisture which may have entered and become
trapped within the refrigerant system. In addition,
during periods of high demand air conditioner opera-
tion, the receiver/drier acts as a reservoir to store
surplus refrigerant. Refrigerant enters the receiver/
drier as a high-pressure, low-temperature liquid.
REMOVAL
WARNING: REVIEW THE WARNINGS AND CAU-
TIONS IN THE FRONT OF THIS SECTION BEFORE
PERFORMING THE FOLLOWING OPERATION (Refer
to 24 - HEATING & AIR CONDITIONING/PLUMBING -
WARNING) and (Refer to 24 - HEATING & AIR CON-
DITIONING/PLUMBING - CAUTION).
(1) Recover the refrigerant from the refrigerant
system(Refer to 24 - HEATING & AIR CONDITION-
ING/PLUMBING - STANDARD PROCEDURE).
(2) Remove the bolts that secure the front and rear
sections of the liquid line to the top of the receiver/
drier (Fig. 15).
(3) Disconnect the liquid line fittings from the
receiver/drier.
(4) Remove the seals from the liquid line fittings
and discard.
(5) Install a plug in, or tape over the opened liquid
line fittings and the receiver/drier ports.
(6) Loosen the clamp that secures the receiver/
drier to the mounting bracket.
(7) Remove the receiver/drier from the engine com-
partment.
INSTALLATION
NOTE: If the receiver/drier is being replaced, add 30
milliliters (1 fluid ounce) of refrigerant oil to the
refrigerant system. Use only refrigerant oil of the
type recommended for the compressor in the vehi-
cle.
(1) Position the receiver/drier onto the mounting
bracket on the front left strut tower.
(2) Tighten the clamp that secures the receiver/
drier to the mounting bracket.
(3) Remove the tape or plugs from the liquid line
fittings and the receiver/drier ports.
(4) Lubricate new rubber O-ring seals with clean
refrigerant oil and install them on the liquid line fit-
tings.
(5) Connect the front and rear sections of the liq-
uid line to the receiver/drier.
(6) Install the bolts that secures the liquid line fit-
tings to the receiver/drier. Tighten the bolts to 7 N´m
(62 in. lbs.).
(7) Evacuate the refrigerant system (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
STANDARD PROCEDURE - REFRIGERANT SYS-
TEM EVACUATE).
(8) Charge the refrigerant system (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
STANDARD PROCEDURE - REFRIGERANT SYS-
TEM CHARGE).
Fig. 15 Receiver/Drier
1 - RECEIVER/DRIER
2 - LIQUID LINE (REAR SECTION)
3 - A/C PRESSURE TRANSDUCER
4 - LIQUID LINE (FRONT SECTION)
5 - CLAMP
24 - 64 PLUMBINGVA

BRAKE/PARK BRAKE INDICATOR -
OPERATION.........................8J-12
BRAKE/PARK LAMP BULB -
INSTALLATION........................8L-7
BRAKE/PARK LAMP BULB - REMOVAL.....8L-7
BRAKES, SPECIAL TOOLS................5-7
BREAKER - DESCRIPTION, CIRCUIT....8W-97-2
BREAKER - DIAGNOSIS AND TESTING,
CIRCUIT.........................8W-97-2
BREAKER - OPERATION, CIRCUIT.....8W-97-2
BREAK-IN - STANDARD PROCEDURE,
COMPRESSOR CLUTCH................24-9
BUCKLE - INSTALLATION, FRONT SEAT
BELT ..............................8O-23
BUCKLE - REMOVAL, FRONT SEAT BELT . . 8O-22
BULB - INSTALLATION, BACKUP LAMP....8L-6
BULB - INSTALLATION, BRAKE/PARK
LAMP...............................8L-7
BULB - INSTALLATION, CARGO/DOME
LAMP..............................8L-27
BULB - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP.................8L-7
BULB - INSTALLATION, CLEARANCE
LAMP...............................8L-8
BULB - INSTALLATION, DOME
LAMP/INTRUSION SENSOR.............8L-30
BULB - INSTALLATION, DOME/READING
LAMP..............................8L-29
BULB - INSTALLATION, ENTRY/EXIT
LAMP..............................8L-32
BULB - INSTALLATION, FOG LAMP.......8L-10
BULB - INSTALLATION, FRONT POSITION
LAMP..............................8L-14
BULB - INSTALLATION, FRONT
TURN/PARK/SIDE MARKER LAMP.......8L-15
BULB - INSTALLATION, HIGH BEAM
HEADLAMP.........................8L-17
BULB - INSTALLATION, LICENSE PLATE
LAMP..............................8L-18
BULB - INSTALLATION, LOW BEAM
HEADLAMP.........................8L-19
BULB - INSTALLATION, REAR SIDE
MARKER LAMP......................8L-21
BULB - INSTALLATION, REAR TURN
LAMP..............................8L-22
BULB - INSTALLATION, REPEATER LAMP . . 8L-22
BULB - REMOVAL, BACKUP LAMP........8L-5
BULB - REMOVAL, BRAKE/PARK LAMP....8L-7
BULB - REMOVAL, CARGO/DOME LAMP . . 8L-27
BULB - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP.................8L-7
BULB - REMOVAL, CLEARANCE LAMP.....8L-8
BULB - REMOVAL, DOME LAMP/
INTRUSION SENSOR..................8L-30
BULB - REMOVAL, DOME/READING
LAMP..............................8L-29
BULB - REMOVAL, ENTRY/EXIT LAMP....8L-31
BULB - REMOVAL, FOG LAMP..........8L-10
BULB - REMOVAL, FRONT POSITION
LAMP..............................8L-14
BULB - REMOVAL, FRONT TURN/PARK/
SIDE MARKER LAMP.................8L-14
BULB - REMOVAL, HIGH BEAM
HEADLAMP.........................8L-17
BULB - REMOVAL, LICENSE PLATE
LAMP..............................8L-17
BULB - REMOVAL, LOW BEAM
HEADLAMP.........................8L-18
BULB - REMOVAL, REAR SIDE MARKER
LAMP..............................8L-21
BULB - REMOVAL, REAR TURN LAMP....8L-21
BULB - REMOVAL, REPEATER LAMP.....8L-22
BULKHEAD - INSTALLATION............8L-29
BULKHEAD - REMOVAL................8L-28
BULKHEAD TRIM PANEL -
INSTALLATION.......................23-69
BULKHEAD TRIM PANEL -
INSTALLATION, BACKLITE..............23-81
BULKHEAD TRIM PANEL - REMOVAL.....23-69
BULKHEAD TRIM PANEL - REMOVAL,
BACKLITE..........................23-81
BUMPER - STEP - INSTALLATION, REAR
. . . 13-3
BUMPER - STEP - REMOVAL, REAR
.......13-3
BUMPER - STEPS - INSTALLATION,
FRONT
..............................13-2
BUMPER - STEPS - REMOVAL, FRONT
.....13-2
BURNT FLUID - DIAGNOSIS AND
TESTING, CAUSES OF
................21-102BUSHINGS - INSTALLATION..............2-3
BUSHINGS - REMOVAL..................2-3
BUZZ, SQUEAK & RATTLE - STANDARD
PROCEDURE........................23-10
CABIN HEATER - DESCRIPTION.........24-72
CABIN HEATER - OPERATION...........24-72
CABLE - DESCRIPTION.................8P-3
CABLE - DIAGNOSIS AND TESTING,
GEARSHIFT........................21-109
CABLE - INSTALLATION, ANTENNA BODY . . 8A-1
CABLE - INSTALLATION, GEARSHIFT....21-109
CABLE - INSTALLATION, INSTRUMENT
PANEL ANTENNA......................8A-2
CABLE - INSTALLATION, LATCH RELEASE . 23-51
CABLE - INSTALLATION, PARK LOCK....21-126
CABLE - REMOVAL, ANTENNA BODY......8A-1
CABLE - REMOVAL, GEARSHIFT........21-109
CABLE - REMOVAL, INSTRUMENT PANEL
ANTENNA...........................8A-1
CABLE - REMOVAL, LATCH RELEASE.....23-51
CABLE - REMOVAL, PARK LOCK........21-125
CABLE TENSIONER - INSTALLATION......5-23
CABLE TENSIONER - REMOVAL..........5-23
CABLES - ADJUSTMENT, PARKING
BRAKE..............................5-25
CABLES - DESCRIPTION, BATTERY.......8F-14
CABLES - DIAGNOSIS AND TESTING,
BATTERY...........................8F-14
CABLES - INSTALLATION, BATTERY......8F-16
CABLES - INSTALLATION, MODE DOOR . . . 24-19
CABLES - OPERATION, BATTERY........8F-14
CABLES - REMOVAL, BATTERY..........8F-16
CABLES - REMOVAL, MODE DOOR.......24-19
CAMSHAFT POSITION - STANDARD
PROCEDURE, CHECKING................9-27
CAMSHAFT POSITION SENSOR -
DESCRIPTION.......................14-19
CAMSHAFT POSITION SENSOR -
INSTALLATION.......................14-19
CAMSHAFT POSITION SENSOR -
OPERATION.........................14-19
CAMSHAFT POSITION SENSOR -
REMOVAL..........................14-19
CAMSHAFT(S) - INSTALLATION..........9-29
CAMSHAFT(S) - REMOVAL..............9-28
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-18
CAP - DIAGNOSIS AND TESTING,
RADIATOR PRESSURE.................7-19
CAP - OPERATION, RADIATOR
PRESSURE..........................7-18
CAPACITIES - SPECIFICATIONS, FLUID......0-4
CAPACITY, SPECIFICATIONS - CHARGE . . . 24-49
CARGO/DOME LAMP BULB -
INSTALLATION.......................8L-27
CARGO/DOME LAMP BULB - REMOVAL . . . 8L-27
CARGO/DOME LAMP UNIT -
INSTALLATION.......................8L-28
CARGO/DOME LAMP UNIT - REMOVAL . . . 8L-28
CARPETS AND FLOOR MATS -
INSTALLATION.......................23-70
CARPETS AND FLOOR MATS - REMOVAL . 23-69
CARRIER - INSTALLATION, SPARE TIRE . . . 22-10
CARRIER - REMOVAL, SPARE TIRE......22-10
CATALYTIC CONVERTER - INSTALLATION . . . 11-3
CATALYTIC CONVERTER - REMOVAL......11-3
CAUSES OF BURNT FLUID - DIAGNOSIS
AND TESTING
......................21-102
CAUTION - CAUTION
..................24-45
CAUTION - REFRIGERANT HOSES/LINES/
TUBES PRECAUTIONS
.................24-45
CAUTION, CAUTION
...................24-45
CAUTION, INTERIOR
..................23-67
CENTER - DESCRIPTION, POWER
DISTRIBUTION
....................8W-97-3
CENTER - OPERATION, POWER
DISTRIBUTION
....................8W-97-3
CENTER BEARING - INSTALLATION
........3-9
CENTER BEARING - REMOVAL
............3-8
CENTER BEZEL - INSTALLATION,
INSTRUMENT PANEL
..................23-55
CENTER BEZEL - REMOVAL,
INSTRUMENT PANEL
..................23-55
CENTER HIGH MOUNTED STOP LAMP
BULB - INSTALLATION
.................8L-7
CENTER HIGH MOUNTED STOP LAMP
BULB - REMOVAL
.....................8L-7CENTER HIGH MOUNTED STOP LAMP
UN - INSTALLATION...................8L-8
CENTER HIGH MOUNTED STOP LAMP
UN - REMOVAL.......................8L-8
CENTER ROLLER ARM - INSTALLATION . . . 23-38
CENTER ROLLER ARM - REMOVAL......23-37
CENTER TRACK - INSTALLATION........23-39
CENTER TRACK - REMOVAL............23-38
CENTERING - STANDARD PROCEDURE,
CLOCKSPRING......................8O-13
CENTRAL TIMER MODULE -
DESCRIPTION........................8E-1
CENTRAL TIMER MODULE - DIAGNOSIS
AND TESTING........................8E-2
CENTRAL TIMER MODULE -
INSTALLATION........................8E-2
CENTRAL TIMER MODULE - OPERATION . . . 8E-2
CENTRAL TIMER MODULE - REMOVAL....8E-2
CHAIN - INSTALLATION, OIL PUMP.......9-54
CHAIN - INSTALLATION, TIMING.........9-67
CHAIN - REMOVAL, OIL PUMP...........9-53
CHAIN - REMOVAL, TIMING.............9-63
CHAIN COVER - INSTALLATION, TIMING . . . 9-60
CHAIN COVER - REMOVAL, TIMING.......9-59
CHAIN TENSIONER - INSTALLATION,
TIMING.............................9-71
CHAIN TENSIONER - REMOVAL, TIMING . . . 9-70
CHAIN TENSIONING RAIL -
INSTALLATION, TIMING.................9-66
CHAIN TENSIONING RAIL - REMOVAL,
TIMING.............................9-63
CHARGE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-48
CHARGE AIR COOLER AND PLUMBING -
CLEANING...........................11-5
CHARGE AIR COOLER AND PLUMBING -
DESCRIPTION........................11-4
CHARGE AIR COOLER AND PLUMBING -
INSPECTION.........................11-5
CHARGE AIR COOLER AND PLUMBING -
INSTALLATION........................11-5
CHARGE AIR COOLER AND PLUMBING -
OPERATION..........................11-4
CHARGE AIR COOLER AND PLUMBING -
REMOVAL...........................11-5
CHARGE AIR COOLER SYSTEM - LEAKS
- DIAGNOSIS AND TESTING.............11-4
CHARGE CAPACITY, SPECIFICATIONS.....24-49
CHARGING - STANDARD PROCEDURE,
BATTERY............................8F-8
CHARGING INDICATOR - DESCRIPTION . . . 8J-13
CHARGING INDICATOR - OPERATION.....8J-13
CHART - SPECIFICATIONS, TORQUE....5-29,5-5
CHART - SPECIFICATIONS, TORQUE.....19-10,
19-14,19-5,19-9
CHART - SPECIFICATIONS, TORQUE....2-12,2-2
CHART, SPECIFICATIONS - TORQUE.......5-22
CHART, SPECIFICATIONS - TORQUE.......22-5
CHECK - INSTALLATION..........23-13,23-24
CHECK - REMOVAL..............23-13,23-24
CHECK OIL LEVEL - STANDARD
PROCEDURE.......................21-102
CHECK VALVE - DESCRIPTION...........8R-7
CHECK VALVE - INSTALLATION..........8R-7
CHECK VALVE - OPERATION.............8R-7
CHECK VALVE - REMOVAL..............8R-7
CHECKING AND REPAIRING
CONNECTING RODS - STANDARD
PROCEDURE.........................9-40
CHECKING BATTERY ELECTROLYTE
LEVEL - STANDARD PROCEDURE........8F-12
CHECKING CAMSHAFT POSITION -
STANDARD PROCEDURE................9-27
CHECKS - DIAGNOSIS AND TESTING,
PRELIMINARY.........................7-1
CHIME WARNING SYSTEM - DIAGNOSIS
AND TESTING........................8B-2
CHIME/BUZZER - DESCRIPTION..........8B-1
CHIME/BUZZER - OPERATION............8B-1
CIGAR LIGHTER OUTLET -
DESCRIPTION.....................8W-97-1
CIGAR LIGHTER OUTLET - DIAGNOSIS
AND TESTING
.....................8W-97-2
CIGAR LIGHTER OUTLET - OPERATION
. 8W-97-2
CIGAR LIGHTER OUTLET - REMOVAL
. . 8W-97-2
CIRCUIT BREAKER - DESCRIPTION
....8W-97-2
CIRCUIT BREAKER - DIAGNOSIS AND
TESTING
.........................8W-97-2
VAINDEX 3
Description Group-Page Description Group-Page Description Group-Page

COVER - REMOVAL, TIMING CHAIN.......9-59
COVER - REMOVAL, TOP..............23-64
COVER - TRAY - INSTALLATION, TOP.....23-64
COVER - TRAY - REMOVAL, TOP........23-63
COVER(S) - INSTALLATION, CYLINDER
HEAD...............................9-30
COVER(S) - REMOVAL, CYLINDER HEAD . . . 9-30
COWL TRIM - INSTALLATION...........23-70
COWL TRIM - REMOVAL...............23-70
CRADLE CROSSMEMBER -
INSTALLATION, ENGINE................13-8
CRADLE CROSSMEMBER - REMOVAL,
ENGINE.............................13-6
CRANKSHAFT - INSTALLATION...........9-36
CRANKSHAFT - REMOVAL..............9-35
CRANKSHAFT AND BLOCK JOURNALS -
STANDARD PROCEDURE, MEASURE......9-35
CRANKSHAFT OIL SEAL - FRONT -
INSTALLATION........................9-38
CRANKSHAFT OIL SEAL - FRONT -
REMOVAL...........................9-38
CRANKSHAFT OIL SEAL - REAR -
INSTALLATION........................9-37
CRANKSHAFT OIL SEAL - REAR -
REMOVAL...........................9-37
CRANKSHAFT POSITION SENSOR -
DESCRIPTION.......................14-20
CRANKSHAFT POSITION SENSOR -
INSTALLATION.......................14-20
CRANKSHAFT POSITION SENSOR -
OPERATION..........................14-20
CRANKSHAFT POSITION SENSOR -
REMOVAL..........................14-20
CROSSMEMBER - INSTALLATION,
ENGINE CRADLE......................13-8
CROSSMEMBER - INSTALLATION,
RADIATOR..........................23-48
CROSSMEMBER - REMOVAL, ENGINE
CRADLE.............................13-6
CROSSMEMBER - REMOVAL, RADIATOR . . 23-47
CROSSMEMBER - TRANSMISSION -
INSTALLATION, REAR..................13-9
CROSSMEMBER - TRANSMISSION -
REMOVAL, REAR......................13-9
CUP HOLDER - INSTALLATION..........23-56
CUP HOLDER - REMOVAL..............23-55
CUSHION - FRONT - INSTALLATION,
SEAT ..............................23-78
CUSHION - FRONT - REMOVAL, SEAT....23-78
CUSHION/COVER - REAR -
INSTALLATION, SEAT.................23-80
CUSHION/COVER - REAR -
INSTALLATION, SEAT BACK............23-80
CUSHION/COVER - REAR - REMOVAL,
SEAT
..............................23-80
CUSHION/COVER - REAR - REMOVAL,
SEAT BACK
.........................23-80
CYLINDER - INSTALLATION, KEY/LOCK
....19-7
CYLINDER - INSTALLATION, LOCK
.......23-18
CYLINDER - INSTALLATION, MASTER
.....5-18
CYLINDER - REMOVAL, KEY/LOCK
........19-6
CYLINDER - REMOVAL, LOCK
...........23-18
CYLINDER - REMOVAL, MASTER
.........5-17
CYLINDER BLEEDING - STANDARD
PROCEDURE, MASTER
.................5-17
CYLINDER BORES - STANDARD
PROCEDURE, MEASURING
..............9-34
CYLINDER HEAD - INSTALLATION
........9-25
CYLINDER HEAD - REMOVAL
............9-22
CYLINDER HEAD BOLT INSPECTION -
STANDARD PROCEDURE
................9-21
CYLINDER HEAD COVER(S) -
INSTALLATION
........................9-30
CYLINDER HEAD COVER(S) - REMOVAL
. . . 9-30
CYLINDER HEAD FRONT COVER -
INSTALLATION
........................9-26
CYLINDER HEAD FRONT COVER -
REMOVAL
...........................9-23
CYLINDER HEAD GUIDE RAIL -
INSTALLATION
........................9-26
CYLINDER HEAD GUIDE RAIL -
REMOVAL
...........................9-24
CYLINDER HEAD SURFACE - STANDARD
PROCEDURE, MEASURE
................9-21
CYLINDER LEAK DOWN TEST -
STANDARD PROCEDURE
.................9-3CYLINDER PRESSURE LOSS -
STANDARD PROCEDURE,
DETERMINING.........................9-4
CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING, MASTER......5-16
DAMPER - INSTALLATION, VIBRATION.....9-48
DAMPER - REMOVAL, VIBRATION........9-47
DAYTIME RUNNING LAMP RELAY -
INSTALLATION........................8L-9
DAYTIME RUNNING LAMP RELAY -
REMOVAL...........................8L-9
DCHA - DIAGNOSIS AND TESTING,
DIESEL SUPPLEMENTAL HEATER........24-72
DECOUPLER - DIAGNOSIS AND
TESTING, GENERATOR................8F-19
DECOUPLER PULLEY - DESCRIPTION,
GENERATOR........................8F-19
DECOUPLER PULLEY - INSTALLATION,
GENERATOR........................8F-21
DECOUPLER PULLEY - OPERATION,
GENERATOR........................8F-19
DECOUPLER PULLEY - REMOVAL,
GENERATOR........................8F-20
DEFROSTER DUCTS - INSTALLATION.....24-33
DEFROSTER DUCTS - REMOVAL.........24-33
DELAY RELAY - INSTALLATION, TIME....8L-33
DELAY RELAY - REMOVAL, TIME........8L-32
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A
SUPPLEMENTAL RESTRAINT............8O-6
DETERMINING CYLINDER PRESSURE
LOSS - STANDARD PROCEDURE..........9-4
DEVICES - STANDARD PROCEDURE,
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE........................8W-01-7
DIAGRAMS - DESCRIPTION, HOW TO
USE WIRING......................8W-01-1
DIAGRAMS, DIAGNOSIS AND TESTING -
SCHEMATICS........................21-47
DIESEL - DESCRIPTION, 2.7L............11-1
DIESEL - SPECIFICATIONS, STARTER
MOTOR............................8F-29
DIESEL - TORQUE, 2.7L...............8F-17
DIESEL - TORQUE, STARTER...........8F-29
DIESEL ENGINE - DESCRIPTION, FUEL
REQUIREMENTS.......................0-1
DIESEL ENGINE - DIAGNOSIS AND
TESTING............................11-2
DIESEL ENGINES - DESCRIPTION,
ENGINE OIL...........................0-3
DIESEL SUPPLEMENTAL HEATER - DCHA
- DIAGNOSIS AND TESTING............24-72
DIMENSIONS - SPECIFICATIONS, FRAME . . . 13-4
DIMENSIONS - SPECIFICATIONS,
OPENING...........................23-90
DIODE - INSTALLATION.............8W-01-9
DIODE - REMOVAL.................8W-01-9
DISCHARGE (ESD) SENSITIVE DEVICES -
STANDARD PROCEDURE,
ELECTROSTATIC...................8W-01-7
DISCHARGE LINE - INSTALLATION, A/C . . . 24-54
DISCHARGE LINE - REMOVAL, A/C.......24-53
DISCONNECTING AND CONNECTING
FUEL LINES - STANDARD PROCEDURE....14-2
DISTRIBUTION - DESCRIPTION,
POWER..........................8W-97-1
DISTRIBUTION - OPERATION, POWER . . 8W-97-1
DISTRIBUTION CENTER - DESCRIPTION,
POWER..........................8W-97-3
DISTRIBUTION CENTER - OPERATION,
POWER..........................8W-97-3
DISTRIBUTION DUCTS - INSTALLATION,
FLOOR.............................24-34
DISTRIBUTION DUCTS - REMOVAL,
FLOOR.............................24-33
DOME LAMP/INTRUSION SENSOR -
INSTALLATION.......................8L-31
DOME LAMP/INTRUSION SENSOR -
REMOVAL..........................8L-31
DOME LAMP/INTRUSION SENSOR BULB
- INSTALLATION
.....................8L-30
DOME LAMP/INTRUSION SENSOR BULB
- REMOVAL
.........................8L-30
DOME/READING LAMP BULB -
INSTALLATION
.......................8L-29
DOME/READING LAMP BULB - REMOVAL
. 8L-29
DOME/READING LAMP UNIT -
INSTALLATION
.......................8L-30DOME/READING LAMP UNIT - REMOVAL . . 8L-30
DOOR - ASSEMBLY...................23-28
DOOR - ASSEMBLY, SLIDING...........23-43
DOOR - DISASSEMBLY................23-26
DOOR - DISASSEMBLY, SLIDING........23-42
DOOR - INSTALLATION...........23-14,23-30
DOOR - INSTALLATION, FUEL FILL.......23-47
DOOR - INSTALLATION, SLIDING........23-44
DOOR - REMOVAL...............23-14,23-25
DOOR - REMOVAL, FUEL FILL..........23-47
DOOR - REMOVAL, SLIDING............23-41
DOOR ACTUATOR - DESCRIPTION,
RECIRCULATION.....................24-20
DOOR ACTUATOR - INSTALLATION,
RECIRCULATION.....................24-21
DOOR ACTUATOR - OPERATION,
RECIRCULATION.....................24-20
DOOR ACTUATOR - REMOVAL,
RECIRCULATION.....................24-21
DOOR CABLES - INSTALLATION, MODE . . . 24-19
DOOR CABLES - REMOVAL, MODE.......24-19
DOOR GLASS - INSTALLATION....23-15,23-31,
23-46
DOOR GLASS - REMOVAL . . . 23-15,23-31,23-46
DOOR INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT................23-87
DOOR INNER BELT WEATHERSTRIP -
REMOVAL, FRONT....................23-87
DOOR JAMB SWITCH - INSTALLATION.....8L-31
DOOR JAMB SWITCH - REMOVAL.......8L-31
DOOR LOCK MOTOR - INSTALLATION.....8N-1
DOOR LOCK MOTOR - REMOVAL.........8N-1
DOOR OPENING SEALS - INSTALLATION . . 23-87
DOOR OPENING SEALS - REMOVAL......23-87
DOOR OUTER BELT WEATHERSTRIP -
INSTALLATION, FRONT................23-87
DOOR OUTER BELT WEATHERSTRIP -
REMOVAL, FRONT....................23-87
DOSING PUMP - DESCRIPTION, FUEL....24-74
DOSING PUMP - INSTALLATION, FUEL....24-74
DOSING PUMP - OPERATION, FUEL......24-74
DOSING PUMP - REMOVAL, FUEL.......24-74
DOUBLE INVERTED FLARING -
STANDARD PROCEDURE.................5-8
D-PILLAR TRIM - INSTALLATION........23-70
D-PILLAR TRIM - REMOVAL............23-70
DRAIN AND FILL - STANDARD
PROCEDURE.........................3-11
DRAINING COOLING SYSTEM -
STANDARD PROCEDURE................7-12
DRAINING WATER FROM FUEL FILTER -
STANDARD PROCEDURES...............14-2
DRAW TEST - STANDARD PROCEDURE,
IGNITION-OFF.......................8F-10
DRIVE BELT - DIAGNOSIS AND TESTING,
ACCESSORY..........................7-5
DRIVE BELTS - INSTALLATION............7-8
DRIVE BELTS - REMOVAL................7-8
DRIVE VISCOUS CLUTCH -
INSTALLATION, FAN...................7-16
DRIVE VISCOUS CLUTCH - REMOVAL,
FAN ................................7-16
DRIVER AIRBAG - DESCRIPTION........8O-16
DRIVER AIRBAG - INSTALLATION.......8O-18
DRIVER AIRBAG - OPERATION..........8O-17
DRIVER AIRBAG - REMOVAL...........8O-17
DRIVER HEATED SEAT SWITCH -
DESCRIPTION........................8G-2
DRIVER HEATED SEAT SWITCH -
DIAGNOSIS AND TESTING..............8G-2
DRIVER HEATED SEAT SWITCH -
INSTALLATION.......................8G-3
DRIVER HEATED SEAT SWITCH -
OPERATION..........................8G-2
DRIVER HEATED SEAT SWITCH -
REMOVAL...........................8G-3
DRIVING CLUTCH K1 - ASSEMBLY.......21-75
DRIVING CLUTCH K1 - DISASSEMBLY....21-74
DRIVING CLUTCH K2 - ASSEMBLY.......21-78
DRIVING CLUTCH K2 - DISASSEMBLY....21-76
DRIVING CLUTCH K3 - ASSEMBLY.......21-80
DRIVING CLUTCH K3 - DISASSEMBLY
....21-80
DRIVING CLUTCHES - DESCRIPTION
.....21-72
DRIVING CLUTCHES - OPERATION
.......21-72
DROP - STANDARD PROCEDURE,
TESTING FOR A VOLTAGE
............8W-01-8
DRUM IN HAT BRAKE - CLEANING,
REAR
...............................5-27
VAINDEX 5
Description Group-Page Description Group-Page Description Group-Page

FREEWHEELING CLUTCH -
DISASSEMBLY......................21-106
FREEWHEELING CLUTCH - OPERATION . . 21-105
FROM FUEL FILTER - STANDARD
PROCEDURES, DRAINING WATER........14-2
FROM GEAR TO COOLER TUBE -
INSTALLATION, RETURN HOSE..........19-15
FROM GEAR TO COOLER TUBE -
REMOVAL, RETURN HOSE.............19-15
FROM PUMP TO COOLER TUBE -
INSTALLATION, RETURN LINE..........19-15
FROM PUMP TO COOLER TUBE -
REMOVAL, RETURN LINE..............19-15
FRONT - INSTALLATION............5-14,5-24
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL............................9-38
FRONT - INSTALLATION, SEAT..........23-77
FRONT - INSTALLATION, SEAT
ADJUSTERS.........................23-78
FRONT - INSTALLATION, SEAT BACK.....23-77
FRONT - INSTALLATION, SEAT CUSHION . . 23-78
FRONT - REMOVAL................5-13,5-24
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL...............................9-38
FRONT - REMOVAL, SEAT..............23-77
FRONT - REMOVAL, SEAT ADJUSTERS . . . 23-78
FRONT - REMOVAL, SEAT BACK.........23-77
FRONT - REMOVAL, SEAT CUSHION......23-78
FRONT BUMPER - STEPS -
INSTALLATION........................13-2
FRONT BUMPER - STEPS - REMOVAL.....13-2
FRONT COVER - INSTALLATION,
CYLINDER HEAD......................9-26
FRONT COVER - REMOVAL, CYLINDER
HEAD...............................9-23
FRONT DOOR INNER BELT
WEATHERSTRIP - INSTALLATION........23-87
FRONT DOOR INNER BELT
WEATHERSTRIP - REMOVAL............23-87
FRONT DOOR OUTER BELT
WEATHERSTRIP - INSTALLATION........23-87
FRONT DOOR OUTER BELT
WEATHERSTRIP - REMOVAL............23-87
FRONT (DRW) - INSTALLATION . . 5-11,5-13,5-21
FRONT (DRW) - REMOVAL.......5-12,5-20,5-9
FRONT FASCIA - INSTALLATION..........13-2
FRONT FASCIA - REMOVAL..............13-2
FRONT LAMP UNIT - ADJUSTMENT......8L-12
FRONT LAMP UNIT - INSTALLATION.....8L-12
FRONT LAMP UNIT - REMOVAL.........8L-12
FRONT POSITION LAMP BULB -
INSTALLATION.......................8L-14
FRONT POSITION LAMP BULB -
REMOVAL..........................8L-14
FRONT SEAT BELT & RETRACTOR -
INSTALLATION......................8O-21
FRONT SEAT BELT & RETRACTOR -
REMOVAL..........................8O-19
FRONT SEAT BELT BUCKLE -
INSTALLATION......................8O-23
FRONT SEAT BELT BUCKLE - REMOVAL . . 8O-22
FRONT (SRW) - INSTALLATION . . 5-10,5-12,5-21
FRONT (SRW) - REMOVAL.......5-11,5-19,5-9
FRONT SUSPENSION, SPECIAL TOOLS....19-11
FRONT SUSPENSION, SPECIAL TOOLS.....2-2
FRONT TURN/PARK/SIDE MARKER LAMP
BULB - INSTALLATION................8L-15
FRONT TURN/PARK/SIDE MARKER LAMP
BULB - REMOVAL....................8L-14
FRONT WHEEL SPEED SENSOR -
INSTALLATION........................5-30
FRONT WHEEL SPEED SENSOR -
REMOVAL...........................5-30
FUEL DOSING PUMP - DESCRIPTION.....24-74
FUEL DOSING PUMP - INSTALLATION....24-74
FUEL DOSING PUMP - OPERATION......24-74
FUEL DOSING PUMP - REMOVAL........24-74
FUEL FILL DOOR - INSTALLATION.......23-47
FUEL FILL DOOR - REMOVAL...........23-47
FUEL FILTER - DESCRIPTION............14-5
FUEL FILTER - INSTALLATION
............14-6
FUEL FILTER - OPERATION
..............14-5
FUEL FILTER - REMOVAL
...............14-5
FUEL FILTER - STANDARD
PROCEDURES, DRAINING WATER
FROM
..............................14-2
FUEL FILTER CLOGGED INDICATOR -
DESCRIPTION
.......................8J-15FUEL FILTER CLOGGED INDICATOR -
OPERATION.........................8J-15
FUEL GAUGE - DESCRIPTION...........8J-16
FUEL GAUGE - OPERATION.............8J-16
FUEL INDICATOR - DESCRIPTION, LOW . . . 8J-18
FUEL INDICATOR - OPERATION, LOW.....8J-18
FUEL INJECTOR, DESCRIPTION.........14-20
FUEL INJECTORS - STANDARD
PROCEDURE, CLEANING...............14-22
FUEL LEVEL SENDING UNIT / SENSOR -
DESCRIPTION.......................14-15
FUEL LEVEL SENDING UNIT / SENSOR -
INSTALLATION.......................14-15
FUEL LEVEL SENDING UNIT / SENSOR -
REMOVAL..........................14-15
FUEL LINE - INSTALLATION............24-76
FUEL LINE - REMOVAL................24-75
FUEL LINES - DIAGNOSIS AND TESTING,
HIGH PRESSURE......................14-1
FUEL LINES - STANDARD PROCEDURE,
DISCONNECTING AND CONNECTING......14-2
FUEL PRESSURE SOLENOID -
DESCRIPTION.......................14-27
FUEL PRESSURE SOLENOID -
INSTALLATION.......................14-28
FUEL PRESSURE SOLENOID -
OPERATION.........................14-27
FUEL PRESSURE SOLENOID - REMOVAL . . 14-28
FUEL PUMP TEST - STANDARD
PROCEDURE, LOW PRESSURE...........14-3
FUEL RAIL - DESCRIPTION..............14-11
FUEL RAIL - INSTALLATION............14-11
FUEL RAIL - OPERATION...............14-11
FUEL RAIL - REMOVAL................14-11
FUEL REQUIREMENTS - DIESEL ENGINE
- DESCRIPTION........................0-1
FUEL SENSOR - DESCRIPTION, WATER
IN ................................14-16
FUEL SENSOR - OPERATION, WATER IN . . 14-16
FUEL SHUTOFF SOL - DESCRIPTION, HI
PRESSURE.........................14-16
FUEL SHUTOFF SOL - OPERATION, HI
PRESSURE.........................14-16
FUEL SUPPLY RESTRICTIONS -
DIAGNOSIS AND TESTING..............14-5
FUEL SYSTEM - DIAGNOSIS AND
TESTING, AIR IN......................14-2
FUEL SYSTEM COMPONENTS -
STANDARD PROCEDURES, CLEANING.....14-2
FUEL SYSTEM PRESSURE - WARNING,
HIGH...............................14-1
FUEL SYSTEM, SPECIAL TOOLS..........14-5
FUEL TANK - DESCRIPTION............14-12
FUEL TANK - INSTALLATION............14-13
FUEL TANK - REMOVAL...............14-12
FUEL TANK MODULE - DESCRIPTION.....14-13
FUEL TANK MODULE - INSTALLATION....14-14
FUEL TANK MODULE - REMOVAL........14-13
FUEL TEMPERATURE SENSOR -
DESCRIPTION.......................14-29
FUEL TEMPERATURE SENSOR -
INSTALLATION.......................14-29
FUEL TEMPERATURE SENSOR -
OPERATION.........................14-29
FUEL TEMPERATURE SENSOR -
REMOVAL..........................14-29
FUNCTION TEST - DIAGNOSIS AND
TESTING............................24-3
FUSE BLOCK #1 - DESCRIPTION......8W-97-2
FUSE BLOCK #1 - INSTALLATION......8W-97-3
FUSE BLOCK #1 - OPERATION........8W-97-2
FUSE BLOCK #1 - REMOVAL.........8W-97-3
FUSE BLOCK #2 - DESCRIPTION......8W-97-3
FUSE BLOCK #2 - OPERATION........8W-97-3
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON.......8W-01-8
GALLERY PLUGS - STANDARD
PROCEDURE, REPLACING ENGINE
CORE AND OIL.......................9-34
GAP - STANDARD PROCEDURE,
COMPRESSOR CLUTCH AIR
.............24-9
GAP AND FLUSH - SPECIFICATIONS
......23-88
GAUGE - DESCRIPTION, ENGINE
TEMPERATURE
......................8J-15
GAUGE - DESCRIPTION, FUEL
...........8J-16
GAUGE - OPERATION, ENGINE
TEMPERATURE
......................8J-15GAUGE - OPERATION, FUEL............8J-16
GAUGES - DIAGNOSIS AND TESTING,
PRESSURE..........................22-8
GEAR - DESCRIPTION..................19-8
GEAR - INSTALLATION.................19-8
GEAR - INSTALLATION, INTERMEDIATE....9-66
GEAR - REMOVAL.....................19-8
GEAR - REMOVAL, INTERMEDIATE........9-61
GEAR SELECTOR INDICATOR -
DESCRIPTION.......................8J-17
GEAR SELECTOR INDICATOR -
OPERATION.........................8J-17
GEAR TO COOLER TUBE -
INSTALLATION, RETURN HOSE FROM....19-15
GEAR TO COOLER TUBE - REMOVAL,
RETURN HOSE FROM.................19-15
GEARSHIFT CABLE - DIAGNOSIS AND
TESTING..........................21-109
GEARSHIFT CABLE - INSTALLATION.....21-109
GEARSHIFT CABLE - REMOVAL........21-109
GEARTRAIN - ASSEMBLY, PLANETARY . . . 21-131
GEARTRAIN - DESCRIPTION,
PLANETARY........................21-130
GEARTRAIN - DISASSEMBLY,
PLANETARY........................21-131
GEARTRAIN - OPERATION, PLANETARY . . 21-130
GENERAL - WARNINGS.............8W-01-6
GENERATOR - DESCRIPTION...........8F-18
GENERATOR - INSTALLATION...........8F-18
GENERATOR - OPERATION.............8F-18
GENERATOR - REMOVAL...............8F-18
GENERATOR DECOUPLER - DIAGNOSIS
AND TESTING.......................8F-19
GENERATOR DECOUPLER PULLEY -
DESCRIPTION.......................8F-19
GENERATOR DECOUPLER PULLEY -
INSTALLATION.......................8F-21
GENERATOR DECOUPLER PULLEY -
OPERATION.........................8F-19
GENERATOR DECOUPLER PULLEY -
REMOVAL..........................8F-20
GLASS - INSTALLATION, DOOR....23-15,23-31,
23-46
GLASS - INSTALLATION, SIDE VIEW
MIRROR...........................23-49
GLASS - REMOVAL, DOOR . . . 23-15,23-31,23-46
GLASS - REMOVAL, SIDE VIEW MIRROR . . 23-49
GLOVE BOX - INSTALLATION...........23-56
GLOVE BOX - REMOVAL...............23-56
GLOW PLUG - INSTALLATION............8I-1
GLOW PLUG - REMOVAL................8I-1
GLOW PLUG RELAY - DESCRIPTION.......8I-2
GLOW PLUG RELAY - OPERATION........8I-2
GLOW PLUG RELAYS - DIAGNOSIS AND
TESTING.............................8I-2
GRILLE - INSTALLATION...............23-47
GRILLE - REMOVAL..................23-47
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO..........8W-01-8
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR..........8W-01-5
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO
..............................8W-01-8
GUIDE RAIL - INSTALLATION, CYLINDER
HEAD
...............................9-26
GUIDE RAIL - REMOVAL, CYLINDER
HEAD
...............................9-24
HANDLE - INSTALLATION, ASSIST
.......23-68
HANDLE - INSTALLATION, EXTERIOR
....23-16,
23-33,23-36
HANDLE - INSTALLATION, LATCH
RELEASE
...........................23-52
HANDLE - REMOVAL, ASSIST
...........23-68
HANDLE - REMOVAL, EXTERIOR
. . . 23-16,23-32,
23-36
HANDLE - REMOVAL, LATCH RELEASE
. . . 23-52
HANDLE ACTUATOR - INSTALLATION,
INSIDE
........................23-34,23-37
HANDLE ACTUATOR - REMOVAL, INSIDE
. 23-34,
23-37
HANDLING NON-DEPLOYED
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE
...............8O-6
HARNESS - DIAGNOSIS AND TESTING,
WIRING
..........................8W-01-6
VAINDEX 7
Description Group-Page Description Group-Page Description Group-Page

HAT BRAKE - CLEANING, REAR DRUM
IN .................................5-27
HCU (HYDRAULIC CONTROL UNIT) -
DESCRIPTION........................5-31
HCU (HYDRAULIC CONTROL UNIT) -
INSTALLATION........................5-32
HCU (HYDRAULIC CONTROL UNIT) -
REMOVAL...........................5-31
HEAD - INSTALLATION, CYLINDER........9-25
HEAD - REMOVAL, CYLINDER...........9-22
HEAD BOLT INSPECTION - STANDARD
PROCEDURE, CYLINDER................9-21
HEAD COVER(S) - INSTALLATION,
CYLINDER...........................9-30
HEAD COVER(S) - REMOVAL, CYLINDER . . . 9-30
HEAD FRONT COVER - INSTALLATION,
CYLINDER...........................9-26
HEAD FRONT COVER - REMOVAL,
CYLINDER...........................9-23
HEAD GUIDE RAIL - INSTALLATION,
CYLINDER...........................9-26
HEAD GUIDE RAIL - REMOVAL,
CYLINDER...........................9-24
HEAD SURFACE - STANDARD
PROCEDURE, MEASURE CYLINDER.......9-21
HEADLAMP BULB - INSTALLATION, HIGH
BEAM..............................8L-17
HEADLAMP BULB - INSTALLATION, LOW
BEAM..............................8L-19
HEADLAMP BULB - REMOVAL, HIGH
BEAM..............................8L-17
HEADLAMP BULB - REMOVAL, LOW
BEAM...............................8L-18
HEADLAMP LEVELING MOTOR -
INSTALLATION.......................8L-16
HEADLAMP LEVELING MOTOR -
REMOVAL..........................8L-15
HEADLAMP LEVELING SWITCH -
INSTALLATION.......................8L-17
HEADLAMP LEVELING SWITCH -
REMOVAL..........................8L-16
HEADLINER - INSTALLATION...........23-71
HEADLINER - REMOVAL...............23-70
HEADREST - INSTALLATION............23-76
HEADREST - REMOVAL................23-76
HEATED SEAT ELEMENT - DESCRIPTION . . . 8G-3
HEATED SEAT ELEMENT - DIAGNOSIS
AND TESTING........................8G-3
HEATED SEAT ELEMENT - OPERATION.....8G-3
HEATED SEAT RELAY - DESCRIPTION.....8G-4
HEATED SEAT RELAY - DIAGNOSIS AND
TESTING............................8G-4
HEATED SEAT RELAY - INSTALLATION.....8G-4
HEATED SEAT RELAY - OPERATION.......8G-4
HEATED SEAT RELAY - REMOVAL........8G-4
HEATED SEAT SENSOR - DESCRIPTION....8G-4
HEATED SEAT SENSOR - DIAGNOSIS
AND TESTING........................8G-4
HEATED SEAT SWITCH - DESCRIPTION,
DRIVER.............................8G-2
HEATED SEAT SWITCH - DESCRIPTION,
PASSENGER.........................8G-5
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING, DRIVER.................8G-2
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING, PASSENGER.............8G-5
HEATED SEAT SWITCH - INSTALLATION,
DRIVER.............................8G-3
HEATED SEAT SWITCH - INSTALLATION,
PASSENGER.........................8G-5
HEATED SEAT SWITCH - OPERATION,
DRIVER.............................8G-2
HEATED SEAT SWITCH - OPERATION,
PASSENGER.........................8G-5
HEATED SEAT SWITCH - REMOVAL,
DRIVER.............................8G-3
HEATED SEAT SWITCH - REMOVAL,
PASSENGER.........................8G-5
HEATED SEATS - DESCRIPTION..........8G-1
HEATED SEATS - DIAGNOSIS AND
TESTING............................8G-2
HEATED SEATS - OPERATION
............8G-2
HEATER - DCHA - DIAGNOSIS AND
TESTING, DIESEL SUPPLEMENTAL
.......24-72
HEATER - DESCRIPTION, CABIN
.........24-72
HEATER - INSTALLATION, ENGINE
BLOCK
..............................7-14
HEATER - OPERATION, CABIN
...........24-72HEATER - REMOVAL, ENGINE BLOCK......7-14
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-2
HEATER CONTROL - DESCRIPTION, A/C . . . 24-12
HEATER CONTROL - INSTALLATION, A/C . . 24-13
HEATER CONTROL - OPERATION, A/C....24-12
HEATER CONTROL - REMOVAL, A/C......24-12
HEATER CORE - DESCRIPTION..........24-57
HEATER CORE - INSTALLATION.........24-58
HEATER CORE - OPERATION............24-57
HEATER CORE - REMOVAL.............24-58
HEATER PERFORMANCE - DIAGNOSIS
AND TESTING........................24-4
HI PRESSURE FUEL SHUTOFF SOL -
DESCRIPTION.......................14-16
HI PRESSURE FUEL SHUTOFF SOL -
OPERATION.........................14-16
HIGH BEAM HEADLAMP BULB -
INSTALLATION.......................8L-17
HIGH BEAM HEADLAMP BULB -
REMOVAL..........................8L-17
HIGH BEAM INDICATOR - DESCRIPTION . . 8J-17
HIGH BEAM INDICATOR - OPERATION....8J-17
HIGH FUEL SYSTEM PRESSURE -
WARNING...........................14-1
HIGH MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER................8L-7
HIGH MOUNTED STOP LAMP BULB -
REMOVAL, CENTER....................8L-7
HIGH MOUNTED STOP LAMP UN -
INSTALLATION, CENTER................8L-8
HIGH MOUNTED STOP LAMP UN -
REMOVAL, CENTER....................8L-8
HIGH PRESSURE FUEL LINES -
DIAGNOSIS AND TESTING..............14-1
HIGH PRESSURE LINES - INSTALLATION . . . 14-7
HIGH PRESSURE LINES - REMOVAL......14-6
HIGH PRESSURE PUMP - DESCRIPTION . . . 14-7
HIGH PRESSURE PUMP - INSTALLATION . . 14-10
HIGH PRESSURE PUMP - REMOVAL......14-8
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE..........................22-6
HINGE - INSTALLATION......23-17,23-34,23-50
HINGE - REMOVAL.........23-17,23-34,23-50
HITCH - INSTALLATION, TRAILER........13-10
HITCH - REMOVAL, TRAILER............13-9
HOAT COOLANT - DESCRIPTION..........0-2
HOISTING - STANDARD PROCEDURE.......0-5
HOLDDOWN - DESCRIPTION, BATTERY . . . 8F-14
HOLDDOWN - INSTALLATION, BATTERY . . . 8F-14
HOLDDOWN - REMOVAL, BATTERY......8F-14
HOLDER - INSTALLATION, CUP.........23-56
HOLDER - REMOVAL, CUP.............23-55
HOLDING CLUTCH B1 - ASSEMBLY.....21-113
HOLDING CLUTCH B1 - DISASSEMBLY . . 21-112
HOLDING CLUTCH B2 - ASSEMBLY.....21-116
HOLDING CLUTCH B2 - DISASSEMBLY . . 21-115
HOLDING CLUTCHES - DESCRIPTION....21-111
HOLDING CLUTCHES - OPERATION.....21-112
HOLE REPAIR - DESCRIPTION,
THREADED........................Intro.-5
HOOD - INSTALLATION................23-50
HOOD - REMOVAL....................23-50
HOOD BATTERY INSTALLATION,
INSTALLATION - UNDER...............8F-13
HOOD BATTERY REMOVAL, REMOVAL -
UNDER.............................8F-12
HORN - INSTALLATION.................8H-1
HORN - REMOVAL....................8H-1
HORN SWITCH - INSTALLATION
..........8H-1
HORN SWITCH - REMOVAL
.............8H-1
HOSE - INSTALLATION, INLET
..........24-78
HOSE - INSTALLATION, PRESSURE
......19-15
HOSE - REMOVAL, INLET
..............24-78
HOSE - REMOVAL, PRESSURE
..........19-15
HOSE FROM GEAR TO COOLER TUBE -
INSTALLATION, RETURN
...............19-15
HOSE FROM GEAR TO COOLER TUBE -
REMOVAL, RETURN
..................19-15
HOSES/LINES/TUBES PRECAUTIONS,
CAUTION - REFRIGERANT
..............24-45
HOSES/TUBES - DESCRIPTION, WASHER
. . 8R-8
HOSES/TUBES - OPERATION, WASHER
....8R-9
HOUSING - ASSEMBLY, HVAC
...........24-36
HOUSING - DISASSEMBLY, HVAC
........24-36HOUSING - INSTALLATION, AIR
CLEANER............................9-20
HOUSING - INSTALLATION, HVAC........24-36
HOUSING - INSTALLATION, REAR A/C....24-41
HOUSING - REMOVAL, AIR CLEANER......9-20
HOUSING - REMOVAL, HVAC...........24-34
HOUSING - REMOVAL, REAR A/C........24-40
HOW TO USE WIRING DIAGRAMS -
DESCRIPTION.....................8W-01-1
HUB / BEARING - INSTALLATION..........2-5
HUB / BEARING - REMOVAL..............2-4
HUB BEARINGS/SEALS - INSTALLATION,
AXLE...............................3-20
HUB BEARINGS/SEALS - REMOVAL,
AXLE...............................3-20
HUB SEAL - INSTALLATION, TORQUE
CONVERTER.......................21-147
HUB SEAL - REMOVAL, TORQUE
CONVERTER.......................21-147
HVAC HOUSING - ASSEMBLY...........24-36
HVAC HOUSING - DISASSEMBLY........24-36
HVAC HOUSING - INSTALLATION........24-36
HVAC HOUSING - REMOVAL............24-34
IDENTIFICATION - DESCRIPTION,
FASTENER.........................Intro.-2
IDENTIFICATION AND INFORMATION -
DESCRIPTION, SECTION.............8W-01-5
IDENTIFICATION NUMBER -
DESCRIPTION, VEHICLE..............Intro.-1
IGNITION CONTROL - SPECIAL TOOLS......8I-1
IGNITION-OFF DRAW TEST - STANDARD
PROCEDURE........................8F-10
INBOARD - INSTALLATION.............8O-30
INBOARD - REMOVAL.................8O-29
IN-CAR TEMPERATURE SENSOR -
DESCRIPTION.......................24-19
IN-CAR TEMPERATURE SENSOR -
DIAGNOSIS AND TESTING.............24-19
IN-CAR TEMPERATURE SENSOR -
OPERATION.........................24-19
IN-CAR TEMPERATURE SENSOR -
REMOVAL..........................24-19
INCORRECT FLUID LEVEL - DIAGNOSIS
AND TESTING, EFFECTS OF............21-102
INDICATOR - DESCRIPTION, ABS.........8J-9
INDICATOR - DESCRIPTION, AIRBAG.....8J-10
INDICATOR - DESCRIPTION, AMBIENT
TEMPERATURE......................8J-11
INDICATOR - DESCRIPTION, BRAKE
WEAR.............................8J-12
INDICATOR - DESCRIPTION, BRAKE/
PARK BRAKE........................8J-11
INDICATOR - DESCRIPTION, CHARGING . . . 8J-13
INDICATOR - DESCRIPTION, COOLANT
LOW...............................8J-14
INDICATOR - DESCRIPTION, FUEL
FILTER CLOGGED.....................8J-15
INDICATOR - DESCRIPTION, GEAR
SELECTOR..........................8J-17
INDICATOR - DESCRIPTION, HIGH BEAM . . 8J-17
INDICATOR - DESCRIPTION, LOW FUEL . . . 8J-18
INDICATOR - DESCRIPTION, LOW OIL
LEVEL.............................8J-18
INDICATOR - DESCRIPTION,
MAINTENANCE.......................8J-19
INDICATOR - DESCRIPTION, MULTI-
FUNCTION..........................8J-20
INDICATOR - DESCRIPTION, SEATBELT . . . 8J-22
INDICATOR - DESCRIPTION, TRACTION
CONTROL...........................8J-24
INDICATOR - DESCRIPTION, TRACTION
CONTROL MALFUNCTION..............8J-25
INDICATOR - DESCRIPTION, TURN
SIGNAL............................8J-25
INDICATOR - DESCRIPTION, WAIT-TO-
START .............................8J-26
INDICATOR - DESCRIPTION, WASHER
FLUID..............................8J-27
INDICATOR - DESCRIPTION, WATER-IN-
FUEL..............................8J-27
INDICATOR - OPERATION, ABS...........8J-9
INDICATOR - OPERATION, AIRBAG
.......8J-10
INDICATOR - OPERATION, AMBIENT
TEMPERATURE
......................8J-11
INDICATOR - OPERATION, BRAKE WEAR
. . 8J-12
INDICATOR - OPERATION, BRAKE/PARK
BRAKE
.............................8J-12
INDICATOR - OPERATION, CHARGING
....8J-13
8 INDEXVA
Description Group-Page Description Group-Page Description Group-Page

INDICATOR - OPERATION, COOLANT
LOW...............................8J-14
INDICATOR - OPERATION, FUEL FILTER
CLOGGED...........................8J-15
INDICATOR - OPERATION, GEAR
SELECTOR..........................8J-17
INDICATOR - OPERATION, HIGH BEAM....8J-17
INDICATOR - OPERATION, LOW FUEL.....8J-18
INDICATOR - OPERATION, LOW OIL
LEVEL.............................8J-18
INDICATOR - OPERATION,
MAINTENANCE.......................8J-19
INDICATOR - OPERATION, MULTI-
FUNCTION..........................8J-21
INDICATOR - OPERATION, SEATBELT.....8J-22
INDICATOR - OPERATION, TRACTION
CONTROL...........................8J-24
INDICATOR - OPERATION, TRACTION
CONTROL MALFUNCTION..............8J-25
INDICATOR - OPERATION, TURN SIGNAL . . 8J-25
INDICATOR - OPERATION, WAIT-TO-
START .............................8J-26
INDICATOR - OPERATION, WASHER
FLUID..............................8J-27
INDICATOR - OPERATION, WATER-IN-
FUEL..............................8J-28
INDICATOR LAMP (MIL) - DESCRIPTION,
MALFUNCTION.......................8J-20
INDICATOR LAMP (MIL) - OPERATION,
MALFUNCTION.......................8J-20
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR................22-8
INFLATION PRESSURES - DESCRIPTION,
TIRE................................22-7
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-12
INJECTOR CLASSIFICATION - STANDARD
PROCEDURE........................14-22
INJECTOR, DESCRIPTION - FUEL........14-20
INJECTORS - STANDARD PROCEDURE,
CLEANING FUEL.....................14-22
INLET AIR TEMPERATURE SENSOR -
DESCRIPTION.......................14-29
INLET AIR TEMPERATURE SENSOR -
INSTALLATION.......................14-30
INLET AIR TEMPERATURE SENSOR -
OPERATION.........................14-29
INLET AIR TEMPERATURE SENSOR -
REMOVAL..........................14-30
INLET HOSE - INSTALLATION...........24-78
INLET HOSE - REMOVAL...............24-78
INNER BELT WEATHERSTRIP -
INSTALLATION, FRONT DOOR...........23-87
INNER BELT WEATHERSTRIP -
REMOVAL, FRONT DOOR..............23-87
INPUT SPEED SENSORS - DESCRIPTION . 21-119
INPUT SPEED SENSORS - OPERATION . . . 21-119
INSIDE HANDLE ACTUATOR -
INSTALLATION..................23-34,23-37
INSIDE HANDLE ACTUATOR -
REMOVAL.....................23-34,23-37
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-2
INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING........................8J-7
INSTRUMENT CLUSTER - INSTALLATION . . . 8J-9
INSTRUMENT CLUSTER - OPERATION.....8J-5
INSTRUMENT CLUSTER - REMOVAL......8J-7
INSTRUMENT PANEL - INSTALLATION....8L-29
INSTRUMENT PANEL - REMOVAL........8L-28
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-2
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-1
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-61
INSTRUMENT PANEL ASSEMBLY -
REMOVAL..........................23-57
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-55
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-55
INSTRUMENT PANEL DUCTS -
INSTALLATION
.......................24-38
INSTRUMENT PANEL DUCTS - REMOVAL
. 24-37
INTAKE MANIFOLD - INSTALLATION
.......9-58
INTAKE MANIFOLD - REMOVAL
..........9-57
INTERIOR - CAUTION
.................23-67INTERIOR - DESCRIPTION, LAMPS/
LIGHTING..........................8L-25
INTERIOR - OPERATION, LAMPS/
LIGHTING..........................8L-26
INTERIOR LIGHTING - SPECIFICATIONS . . . 8L-26
INTERMEDIATE GEAR - INSTALLATION.....9-66
INTERMEDIATE GEAR - REMOVAL........9-61
INTERMEDIATE SHAFT - INSTALLATION....19-5
INTERMEDIATE SHAFT - REMOVAL.......19-5
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-2
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-9
INTRUSION SENSOR - INSTALLATION.....8Q-2
INTRUSION SENSOR - REMOVAL.........8Q-2
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE..................5-8
ISO FLARING - STANDARD PROCEDURE....5-8
JAMB SWITCH - INSTALLATION, DOOR . . . 8L-31
JAMB SWITCH - REMOVAL, DOOR.......8L-31
JET - DESCRIPTION, OIL................9-51
JET - INSTALLATION, OIL...............9-51
JET - REMOVAL, OIL...................9-51
JOINT - INSTALLATION, LOWER BALL......2-6
JOINT - REMOVAL, LOWER BALL..........2-6
JOURNALS - STANDARD PROCEDURE,
MEASURE CRANKSHAFT AND BLOCK......9-35
JUMP STARTING - STANDARD
PROCEDURE............................0-6
K1 - ASSEMBLY, DRIVING CLUTCH.......21-75
K1 - DISASSEMBLY, DRIVING CLUTCH....21-74
K2 - ASSEMBLY, DRIVING CLUTCH.......21-78
K2 - DISASSEMBLY, DRIVING CLUTCH....21-76
K3 - ASSEMBLY, DRIVING CLUTCH.......21-80
K3 - DISASSEMBLY, DRIVING CLUTCH....21-80
KEY - DESCRIPTION, TRANSPONDER.....8Q-5
KEY - OPERATION, TRANSPONDER.......8Q-5
KEY REMOTE ENTRY MODULE -
DESCRIPTION, SENTRY................8Q-2
KEY REMOTE ENTRY MODULE -
INSTALLATION, SENTRY................8Q-4
KEY REMOTE ENTRY MODULE -
OPERATION, SENTRY..................8Q-3
KEY REMOTE ENTRY MODULE -
REMOVAL, SENTRY...................8Q-3
KEYLESS ENTRY TRANSMITTER -
DESCRIPTION, REMOTE................8N-2
KEY/LOCK CYLINDER - INSTALLATION.....19-7
KEY/LOCK CYLINDER - REMOVAL........19-6
KNUCKLE - INSTALLATION...............2-5
KNUCKLE - REMOVAL...................2-5
LAMP BULB - INSTALLATION, BACKUP....8L-6
LAMP BULB - INSTALLATION,
BRAKE/PARK.........................8L-7
LAMP BULB - INSTALLATION,
CARGO/DOME.......................8L-27
LAMP BULB - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-7
LAMP BULB - INSTALLATION,
CLEARANCE..........................8L-8
LAMP BULB - INSTALLATION,
DOME/READING.....................8L-29
LAMP BULB - INSTALLATION,
ENTRY/EXIT.........................8L-32
LAMP BULB - INSTALLATION, FOG.......8L-10
LAMP BULB - INSTALLATION, FRONT
POSITION..........................8L-14
LAMP BULB - INSTALLATION, FRONT
TURN/PARK/SIDE MARKER.............8L-15
LAMP BULB - INSTALLATION, LICENSE
PLATE .............................8L-18
LAMP BULB - INSTALLATION, REAR
SIDE MARKER.......................8L-21
LAMP BULB - INSTALLATION, REAR
TURN..............................8L-22
LAMP BULB - INSTALLATION, REPEATER . . 8L-22
LAMP BULB - REMOVAL, BACKUP........8L-5
LAMP BULB - REMOVAL, BRAKE/PARK....8L-7
LAMP BULB - REMOVAL, CARGO/DOME . . 8L-27
LAMP BULB - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-7
LAMP BULB - REMOVAL, CLEARANCE
.....8L-8
LAMP BULB - REMOVAL, DOME/
READING
...........................8L-29
LAMP BULB - REMOVAL, ENTRY/EXIT
....8L-31
LAMP BULB - REMOVAL, FOG
..........8L-10
LAMP BULB - REMOVAL, FRONT
POSITION
..........................8L-14LAMP BULB - REMOVAL, FRONT
TURN/PARK/SIDE MARKER.............8L-14
LAMP BULB - REMOVAL, LICENSE
PLATE .............................8L-17
LAMP BULB - REMOVAL, REAR SIDE
MARKER...........................8L-21
LAMP BULB - REMOVAL, REAR TURN....8L-21
LAMP BULB - REMOVAL, REPEATER.....8L-22
LAMP (MIL) - DESCRIPTION,
MALFUNCTION INDICATOR.............8J-20
LAMP (MIL) - OPERATION,
MALFUNCTION INDICATOR.............8J-20
LAMP RELAY - INSTALLATION, DAYTIME
RUNNING............................8L-9
LAMP RELAY - INSTALLATION, FOG......8L-11
LAMP RELAY - REMOVAL, DAYTIME
RUNNING............................8L-9
LAMP RELAY - REMOVAL, FOG.........8L-10
LAMP SWITCH - INSTALLATION, BRAKE . . . 8L-6
LAMP SWITCH - INSTALLATION, FOG....8L-12
LAMP SWITCH - REMOVAL, BRAKE.......8L-6
LAMP SWITCH - REMOVAL, FOG........8L-11
LAMP UN - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-8
LAMP UN - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-8
LAMP UNIT - ADJUSTMENT, FRONT......8L-12
LAMP UNIT - INSTALLATION, ASH
RECEIVER/CIGAR LIGHTER.............8L-27
LAMP UNIT - INSTALLATION, CARGO/
DOME...............................8L-28
LAMP UNIT - INSTALLATION,
CLEARANCE..........................8L-9
LAMP UNIT - INSTALLATION, DOME/
READING...........................8L-30
LAMP UNIT - INSTALLATION, ENTRY/
EXIT...............................8L-32
LAMP UNIT - INSTALLATION, FRONT.....8L-12
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-18
LAMP UNIT - INSTALLATION, REPEATER . . 8L-23
LAMP UNIT - INSTALLATION, TAIL.......8L-23
LAMP UNIT - REMOVAL, ASH
RECEIVER/CIGAR LIGHTER.............8L-27
LAMP UNIT - REMOVAL, CARGO/DOME . . . 8L-28
LAMP UNIT - REMOVAL, CLEARANCE.....8L-8
LAMP UNIT - REMOVAL, DOME/
READING...........................8L-30
LAMP UNIT - REMOVAL, ENTRY/EXIT....8L-32
LAMP UNIT - REMOVAL, FRONT.........8L-12
LAMP UNIT - REMOVAL, LICENSE PLATE . . 8L-18
LAMP UNIT - REMOVAL, REPEATER......8L-22
LAMP UNIT - REMOVAL, TAIL...........8L-23
LAMP/INTRUSION SENSOR -
INSTALLATION, DOME.................8L-31
LAMP/INTRUSION SENSOR - REMOVAL,
DOME.............................8L-31
LAMP/INTRUSION SENSOR BULB -
INSTALLATION, DOME.................8L-30
LAMP/INTRUSION SENSOR BULB -
REMOVAL, DOME....................8L-30
LAMPS/LIGHTING - EXTERIOR -
DESCRIPTION........................8L-2
LAMPS/LIGHTING - EXTERIOR -
OPERATION..........................8L-3
LAMPS/LIGHTING - EXTERIOR -
SPECIFICATIONS......................8L-5
LAMPS/LIGHTING - INTERIOR -
DESCRIPTION.......................8L-25
LAMPS/LIGHTING - INTERIOR -
OPERATION.........................8L-26
LATCH - INSTALLATION.....23-18,23-35,23-51
LATCH - INSTALLATION, REAR..........23-40
LATCH - INSTALLATION, SAFETY........23-52
LATCH / LOCK CONTROL -
INSTALLATION.......................23-40
LATCH / LOCK CONTROL - REMOVAL.....23-39
LATCH - REMOVAL.........23-18,23-34,23-51
LATCH - REMOVAL, REAR..............23-40
LATCH - REMOVAL, SAFETY............23-52
LATCH RELEASE CABLE - INSTALLATION . . 23-51
LATCH RELEASE CABLE - REMOVAL.....23-51
LATCH RELEASE HANDLE -
INSTALLATION
.......................23-52
LATCH RELEASE HANDLE - REMOVAL
....23-52
LATCH STRIKER - INSTALLATION
........23-18
LATCH STRIKER - INSTALLATION, REAR
. . 23-41
LATCH STRIKER - REMOVAL
...........23-18
VAINDEX 9
Description Group-Page Description Group-Page Description Group-Page

LATCH STRIKER - REMOVAL, REAR......23-41
LEAD - DIAGNOSIS AND TESTING,
TIRE/VEHICLE........................22-8
LEAK DOWN TEST - STANDARD
PROCEDURE, CYLINDER.................9-3
LEAKAGE - DIAGNOSIS AND TESTING,
PUMP.............................19-12
LEAKS - DIAGNOSIS AND TESTING,
CHARGE AIR COOLER SYSTEM..........11-4
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM....................7-10
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-46
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-1
LEAKS - STANDARD PROCEDURE,
REPAIRING.........................22-10
LEFT MOUNT - INSTALLATION...........9-49
LEFT MOUNT - REMOVAL...............9-49
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID........21-102
LEVEL - STANDARD PROCEDURE,
BRAKE FLUID........................5-14
LEVEL - STANDARD PROCEDURE,
CHECK OIL........................21-102
LEVEL - STANDARD PROCEDURE,
CHECKING BATTERY ELECTROLYTE......8F-12
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL...................24-65
LEVEL INDICATOR - DESCRIPTION, LOW
OIL................................8J-18
LEVEL INDICATOR - OPERATION, LOW
OIL.................................8J-18
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL..................14-15
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL.................14-15
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL.....................14-15
LEVEL SENSOR - INSTALLATION,
COOLANT............................7-13
LEVEL SENSOR - REMOVAL, COOLANT....7-13
LEVEL SWITCH - DESCRIPTION,
WASHER FLUID......................8R-7
LEVEL SWITCH - OPERATION, WASHER
FLUID..............................8R-8
LEVELING MOTOR - INSTALLATION,
HEADLAMP.........................8L-16
LEVELING MOTOR - REMOVAL,
HEADLAMP.........................8L-15
LEVELING SWITCH - INSTALLATION,
HEADLAMP.........................8L-17
LEVELING SWITCH - REMOVAL,
HEADLAMP.........................8L-16
LEVER - INSTALLATION................5-26
LEVER - INSTALLATION, ALB............5-15
LEVER - REMOVAL....................5-26
LEVER - REMOVAL, ALB................5-15
LICENSE PLATE BRACKET -
INSTALLATION.......................23-47
LICENSE PLATE BRACKET - REMOVAL....23-47
LICENSE PLATE LAMP BULB -
INSTALLATION.......................8L-18
LICENSE PLATE LAMP BULB - REMOVAL . . 8L-17
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-18
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-18
LIGHTER LAMP UNIT - INSTALLATION,
ASH RECEIVER/CIGAR.................8L-27
LIGHTER LAMP UNIT - REMOVAL, ASH
RECEIVER/CIGAR.....................8L-27
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-1
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIGHTER OUTLET - REMOVAL, CIGAR . . 8W-97-2
LIGHTING - SPECIFICATIONS, INTERIOR . . 8L-26
LINE - DESCRIPTION, REFRIGERANT.....24-44
LINE - INSTALLATION, A/C DISCHARGE . . . 24-54
LINE - INSTALLATION, FUEL............24-76
LINE - INSTALLATION, LIQUID..........24-59
LINE - INSTALLATION, SUCTION.........24-66
LINE - OPERATION, REFRIGERANT
.......24-44
LINE - REMOVAL, A/C DISCHARGE
.......24-53
LINE - REMOVAL, FUEL
................24-75
LINE - REMOVAL, LIQUID
..............24-58
LINE - REMOVAL, SUCTION
............24-66LINE FROM PUMP TO COOLER TUBE -
INSTALLATION, RETURN...............19-15
LINE FROM PUMP TO COOLER TUBE -
REMOVAL, RETURN..................19-15
LINES - DIAGNOSIS AND TESTING, HIGH
PRESSURE FUEL......................14-1
LINES - INSTALLATION, HIGH PRESSURE . . 14-7
LINES - INSTALLATION, OIL COOLER......9-50
LINES - INSTALLATION, UNDERBODY....24-69
LINES - REMOVAL, HIGH PRESSURE......14-6
LINES - REMOVAL, OIL COOLER.........9-50
LINES - REMOVAL, UNDERBODY........24-68
LINES - STANDARD PROCEDURE,
DISCONNECTING AND CONNECTING
FUEL...............................14-2
LINK - INSTALLATION, STABILIZER....2-16,2-9
LINK - REMOVAL, STABILIZER........2-16,2-9
LINKAGE - DESCRIPTION, WIPER.......8R-17
LINKAGE - INSTALLATION, WIPER.......8R-18
LINKAGE - OPERATION, WIPER.........8R-17
LINKAGE - REMOVAL, WIPER...........8R-17
LIQUID LINE - INSTALLATION...........24-59
LIQUID LINE - REMOVAL..............24-58
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL......8W-01-8
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE...................8W-91-1
LOCATIONS - INSPECTION, FLUID
FILL/CHECK............................0-4
LOCK CABLE - INSTALLATION, PARK....21-126
LOCK CABLE - REMOVAL, PARK........21-125
LOCK CONTROL - INSTALLATION, LATCH . . 23-40
LOCK CONTROL - REMOVAL, LATCH.....23-39
LOCK CYLINDER - INSTALLATION.......23-18
LOCK CYLINDER - REMOVAL...........23-18
LOCK MOTOR - INSTALLATION, DOOR....8N-1
LOCK MOTOR - REMOVAL, DOOR........8N-1
LOCK SWITCH - DESCRIPTION, MASTER . . . 8N-2
LOCK SWITCH - DIAGNOSIS AND
TESTING, MASTER....................8N-2
LOCK SWITCH - INSTALLATION, MASTER . . 8N-2
LOCK SWITCH - REMOVAL, MASTER......8N-2
LOCKS - DESCRIPTION, POWER.........8N-1
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-34
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-33
LOSS - STANDARD PROCEDURE,
DETERMINING CYLINDER PRESSURE......9-4
LOW BEAM HEADLAMP BULB -
INSTALLATION.......................8L-19
LOW BEAM HEADLAMP BULB -
REMOVAL..........................8L-18
LOW FUEL INDICATOR - DESCRIPTION . . . 8J-18
LOW FUEL INDICATOR - OPERATION.....8J-18
LOW INDICATOR - DESCRIPTION,
COOLANT...........................8J-14
LOW INDICATOR - OPERATION,
COOLANT...........................8J-14
LOW OIL LEVEL INDICATOR -
DESCRIPTION.......................8J-18
LOW OIL LEVEL INDICATOR -
OPERATION.........................8J-18
LOW PRESSURE FUEL PUMP TEST -
STANDARD PROCEDURE................14-3
LOW PRESSURE PUMP - DESCRIPTION . . . 14-7
LOW PRESSURE PUMP - INSTALLATION . . 14-11
LOW PRESSURE PUMP - OPERATION.....14-8
LOW PRESSURE PUMP - REMOVAL
.......14-9
LOWER BALL JOINT - INSTALLATION
......2-6
LOWER BALL JOINT - REMOVAL
..........2-6
LOWER CONTROL ARM - INSTALLATION
....2-6
LOWER CONTROL ARM - REMOVAL
.......2-6
LOWER ROLLER ARM - INSTALLATION
. . . 23-38
LOWER ROLLER ARM - REMOVAL
.......23-38
LUBRICANT RECOMMENDATIONS -
STANDARD PROCEDURE, PARTS
..........0-5
MAINTENANCE INDICATOR -
DESCRIPTION
.......................8J-19
MAINTENANCE INDICATOR - OPERATION
. . 8J-19
MAINTENANCE SCHEDULES -
DESCRIPTION
.........................0-7
MALFUNCTION INDICATOR -
DESCRIPTION, TRACTION CONTROL
.....8J-25
MALFUNCTION INDICATOR -
OPERATION, TRACTION CONTROL
.......8J-25MALFUNCTION INDICATOR LAMP (MIL) -
DESCRIPTION.......................8J-20
MALFUNCTION INDICATOR LAMP (MIL) -
OPERATION.........................8J-20
MANIFOLD - INSTALLATION, EXHAUST....9-59
MANIFOLD - INSTALLATION, INTAKE......9-58
MANIFOLD - REMOVAL, EXHAUST........9-59
MANIFOLD - REMOVAL, INTAKE..........9-57
MANIFOLD AIR FLOW (MAF) SENSOR -
DESCRIPTION.......................14-30
MANIFOLD AIR FLOW (MAF) SENSOR -
INSTALLATION.......................14-31
MANIFOLD AIR FLOW (MAF) SENSOR -
OPERATION.........................14-30
MANIFOLD AIR FLOW (MAF) SENSOR -
REMOVAL..........................14-31
MANUAL - INSTALLATION, WINDOW
REGULATOR........................23-23
MANUAL - REMOVAL, WINDOW
REGULATOR........................23-22
MANUAL BLEEDING - STANDARD
PROCEDURE..........................5-4
MARKER LAMP BULB - INSTALLATION,
FRONT TURN/PARK/SIDE..............8L-15
MARKER LAMP BULB - INSTALLATION,
REAR SIDE.........................8L-21
MARKER LAMP BULB - REMOVAL,
FRONT TURN/PARK/SIDE..............8L-14
MARKER LAMP BULB - REMOVAL, REAR
SIDE..............................8L-21
MASTER CYLINDER - INSTALLATION......5-18
MASTER CYLINDER - REMOVAL...........5-17
MASTER CYLINDER BLEEDING -
STANDARD PROCEDURE................5-17
MASTER CYLINDER/POWER BOOSTER -
DIAGNOSIS AND TESTING..............5-16
MASTER LOCK SWITCH - DESCRIPTION . . . 8N-2
MASTER LOCK SWITCH - DIAGNOSIS
AND TESTING........................8N-2
MASTER LOCK SWITCH - INSTALLATION . . 8N-2
MASTER LOCK SWITCH - REMOVAL......8N-2
MATCH MOUNTING - STANDARD
PROCEDURE.........................22-2
MATS - INSTALLATION, CARPETS AND
FLOOR.............................23-70
MATS - REMOVAL, CARPETS AND
FLOOR.............................23-69
MEASURE CRANKSHAFT AND BLOCK
JOURNALS - STANDARD PROCEDURE.....9-35
MEASURE CYLINDER HEAD SURFACE -
STANDARD PROCEDURE................9-21
MEASURING CYLINDER BORES -
STANDARD PROCEDURE................9-34
MEASURING PISTON PROTRUSION -
STANDARD PROCEDURE................9-42
MECHANISM - DESCRIPTION, SHIFT....21-133
MECHANISM - INSTALLATION, SHIFT....21-135
MECHANISM - OPERATION, SHIFT......21-133
MECHANISM - REMOVAL, SHIFT.......21-134
METRIC SYSTEM - DESCRIPTION......Intro.-5
MICRO 420 BATTERY TESTER -
STANDARD PROCEDURE, USING........8F-11
MIRROR - GLASS - INSTALLATION, SIDE
VIEW..............................23-49
MIRROR - GLASS - REMOVAL, SIDE
VIEW..............................23-49
MIRROR - INSTALLATION, SIDE VIEW....23-48
MIRROR - REMOVAL, REAR VIEW.......23-72
MIRROR - REMOVAL, SIDE VIEW
........23-48
MIRROR SUPPORT BRACKET -
INSTALLATION, REAR VIEW
............23-72
MIRROR SWITCH - DIAGNOSIS AND
TESTING, POWER
.....................8N-3
MIRROR SWITCH - INSTALLATION,
POWER
.............................8N-4
MIRROR SWITCH - REMOVAL, POWER
....8N-3
MIRRORS - DESCRIPTION, POWER
.......8N-3
MODE DOOR CABLES - INSTALLATION
. . . 24-19
MODE DOOR CABLES - REMOVAL
.......24-19
MODULE - DESCRIPTION, AIRBAG
CONTROL
...........................8O-8
MODULE - DESCRIPTION, CENTRAL
TIMER
..............................8E-1
MODULE - DESCRIPTION, CONTROL
.....24-24
MODULE - DESCRIPTION, ENGINE
CONTROL
...........................8E-3
MODULE - DESCRIPTION, FUEL TANK
....14-13
10 INDEXVA
Description Group-Page Description Group-Page Description Group-Page

PANEL CENTER BEZEL - REMOVAL,
INSTRUMENT.......................23-55
PANEL DUCTS - INSTALLATION,
INSTRUMENT.......................24-38
PANEL DUCTS - REMOVAL,
INSTRUMENT.......................24-37
PANEL REPAIR - STANDARD
PROCEDURE, PLASTIC BODY............23-3
PARK BRAKE, SPECIAL TOOLS...........5-23
PARK BRAKE SWITCH - INSTALLATION . . . 8L-20
PARK BRAKE SWITCH - REMOVAL.......8L-20
PARK LOCK CABLE - INSTALLATION.....21-126
PARK LOCK CABLE - REMOVAL........21-125
PARKING BRAKE CABLES -
ADJUSTMENT........................5-25
PARK/NEUTRAL CONTACT -
DESCRIPTION......................21-139
PARK/NEUTRAL CONTACT - OPERATION . 21-140
PARTS & LUBRICANT
RECOMMENDATIONS - STANDARD
PROCEDURE..........................0-5
PASSENGER AIRBAG - DESCRIPTION....8O-23
PASSENGER AIRBAG - INSTALLATION....8O-26
PASSENGER AIRBAG - OPERATION......8O-24
PASSENGER AIRBAG - REMOVAL........8O-24
PASSENGER AIRBAG BRACKET -
INSTALLATION......................8O-27
PASSENGER AIRBAG BRACKET -
REMOVAL..........................8O-27
PASSENGER HEATED SEAT SWITCH -
DESCRIPTION.........................8G-5
PASSENGER HEATED SEAT SWITCH -
DIAGNOSIS AND TESTING..............8G-5
PASSENGER HEATED SEAT SWITCH -
INSTALLATION.......................8G-5
PASSENGER HEATED SEAT SWITCH -
OPERATION..........................8G-5
PASSENGER HEATED SEAT SWITCH -
REMOVAL...........................8G-5
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-8
PEDAL - INSTALLATION................5-19
PEDAL - REMOVAL....................5-18
PEDAL POSITION SENSOR -
DESCRIPTION, ACCELERATOR..........14-17
PERFORMANCE - DIAGNOSIS AND
TESTING, HEATER.....................24-4
PERFORMANCE TEST - DIAGNOSIS AND
TESTING, A/C........................24-3
PILLAR - INSTALLATION, REAR.........8L-29
PILLAR - REMOVAL, REAR.............8L-28
PINION SEAL - INSTALLATION...........3-22
PINION SEAL - REMOVAL...............3-22
PIPE - INSTALLATION, EXHAUST.........11-3
PIPE - REMOVAL, EXHAUST.............11-3
PISTON & CONNECTING ROD -
DESCRIPTION........................9-40
PISTON PROTRUSION - STANDARD
PROCEDURE, MEASURING..............9-42
PISTON RING FITTING - STANDARD
PROCEDURE.........................9-46
PISTONS - DESCRIPTION.............21-128
PISTONS - OPERATION...............21-128
PLANETARY GEARTRAIN - ASSEMBLY . . . 21-131
PLANETARY GEARTRAIN - DESCRIPTION . 21-130
PLANETARY GEARTRAIN -
DISASSEMBLY......................21-131
PLANETARY GEARTRAIN - OPERATION . . 21-130
PLASTIC BODY PANEL REPAIR -
STANDARD PROCEDURE................23-3
PLATE BRACKET - INSTALLATION,
LICENSE...........................23-47
PLATE BRACKET - REMOVAL, LICENSE . . . 23-47
PLATE LAMP BULB - INSTALLATION,
LICENSE...........................8L-18
PLATE LAMP BULB - REMOVAL,
LICENSE...........................8L-17
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-18
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-18
PLATES - INSTALLATION, SPRING
CLAMP..............................2-8
PLATES - INSTALLATION, SPRING STOP....2-9
PLATES - REMOVAL, SPRING CLAMP
......2-8
PLATES - REMOVAL, SPRING STOP
........2-9
PLUG - INSTALLATION, GLOW
............8I-1
PLUG - REMOVAL, GLOW
...............8I-1
PLUG RELAY - DESCRIPTION, GLOW
......8I-2PLUG RELAY - OPERATION, GLOW........8I-2
PLUG RELAYS - DIAGNOSIS AND
TESTING, GLOW.......................8I-2
PLUGS - STANDARD PROCEDURE,
REPLACING ENGINE CORE AND OIL
GALLERY............................9-34
PLUMBING - CLEANING, CHARGE AIR
COOLER.............................11-5
PLUMBING - DESCRIPTION, CHARGE
AIR COOLER.........................11-4
PLUMBING - INSPECTION, CHARGE AIR
COOLER.............................11-5
PLUMBING - INSTALLATION, CHARGE
AIR COOLER.........................11-5
PLUMBING - OPERATION, CHARGE AIR
COOLER.............................11-4
PLUMBING - REMOVAL, CHARGE AIR
COOLER.............................11-5
PLUMBING - WARNING................24-44
PLY TIRES - DESCRIPTION, RADIAL.......22-6
POLISH - DESCRIPTION, FINESSE
SANDING/BUFFING...................23-75
POSITION - STANDARD PROCEDURE,
CHECKING CAMSHAFT.................9-27
POSITION LAMP BULB - INSTALLATION,
FRONT.............................8L-14
POSITION LAMP BULB - REMOVAL,
FRONT.............................8L-14
POSITION SENSOR - DESCRIPTION,
ACCELERATOR PEDAL.................14-17
POSITION SENSOR - DESCRIPTION,
CAMSHAFT.........................14-19
POSITION SENSOR - DESCRIPTION,
CRANKSHAFT.......................14-20
POSITION SENSOR - INSTALLATION,
CAMSHAFT.........................14-19
POSITION SENSOR - INSTALLATION,
CRANKSHAFT.......................14-20
POSITION SENSOR - OPERATION,
CAMSHAFT.........................14-19
POSITION SENSOR - OPERATION,
CRANKSHAFT.......................14-20
POSITION SENSOR - REMOVAL,
CAMSHAFT.........................14-19
POSITION SENSOR - REMOVAL,
CRANKSHAFT.......................14-20
POTENTIAL - STANDARD PROCEDURE,
TESTING OF VOLTAGE..............8W-01-7
POWER - INSTALLATION, WINDOW
REGULATOR........................23-21
POWER - REMOVAL, WINDOW
REGULATOR........................23-20
POWER BRAKE BOOSTER -
DESCRIPTION........................5-19
POWER BRAKE BOOSTER -
INSTALLATION........................5-19
POWER BRAKE BOOSTER - OPERATION . . . 5-19
POWER BRAKE BOOSTER - REMOVAL.....5-19
POWER DISTRIBUTION - DESCRIPTION . 8W-97-1
POWER DISTRIBUTION - OPERATION . . 8W-97-1
POWER DISTRIBUTION CENTER -
DESCRIPTION.....................8W-97-3
POWER DISTRIBUTION CENTER -
OPERATION.......................8W-97-3
POWER LOCKS - DESCRIPTION..........8N-1
POWER MIRROR SWITCH - DIAGNOSIS
AND TESTING........................8N-3
POWER MIRROR SWITCH -
INSTALLATION.......................8N-4
POWER MIRROR SWITCH - REMOVAL....8N-3
POWER MIRRORS - DESCRIPTION.......8N-3
POWER OUTLET - DESCRIPTION......8W-97-3
POWER OUTLET - DIAGNOSIS AND
TESTING.........................8W-97-4
POWER OUTLET - INSTALLATION.....8W-97-4
POWER OUTLET - OPERATION........8W-97-4
POWER OUTLET - REMOVAL.........8W-97-4
POWER STEERING FLUID -
DESCRIPTION
.........................0-3
POWER STEERING PUMP - INITIAL
OPERATION - STANDARD PROCEDURE
. . . 19-12
POWER STEERING PUMP FILL AND
BLEED PROCEDURE, STANDARD
PROCEDURE
........................19-14
POWER STEERING SYSTEM -
DIAGNOSIS AND TESTING
..............19-2
POWER STEERING SYSTEM -
STANDARD PROCEDURE, FLUSHING
.....19-13POWER WINDOW SWITCH - DIAGNOSIS
AND TESTING........................8N-5
POWER WINDOW SWITCH -
INSTALLATION.......................8N-6
POWER WINDOW SWITCH - REMOVAL....8N-6
POWER WINDOWS - DESCRIPTION.......8N-5
POWER WINDOWS - OPERATION.........8N-5
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON FUSES . 8W-01-8
PRE-ALIGNMENT INSPECTION -
DIAGNOSIS AND TESTING..............2-17
PRECAUTIONS AND WARNINGS,
WARNING - SAFETY...................23-1
PRECAUTIONS, CAUTION -
REFRIGERANT HOSES/LINES/TUBES......24-45
PRECAUTIONS, WARNING -
WINDSHIELD SAFETY.................23-82
PRELIMINARY - DIAGNOSIS AND
TESTING...........................21-23
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING.........................7-1
PRESSURE - WARNING, HIGH FUEL
SYSTEM............................14-1
PRESSURE BLEEDING - STANDARD
PROCEDURE..........................5-5
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-18
PRESSURE CAP - DIAGNOSIS AND
TESTING, RADIATOR...................7-19
PRESSURE CAP - OPERATION,
RADIATOR...........................7-18
PRESSURE FOR HIGH SPEEDS -
DESCRIPTION, TIRE...................22-6
PRESSURE FUEL LINES - DIAGNOSIS
AND TESTING, HIGH...................14-1
PRESSURE FUEL PUMP TEST -
STANDARD PROCEDURE, LOW...........14-3
PRESSURE FUEL SHUTOFF SOL -
DESCRIPTION, HI....................14-16
PRESSURE FUEL SHUTOFF SOL -
OPERATION, HI......................14-16
PRESSURE GAUGES - DIAGNOSIS AND
TESTING............................22-8
PRESSURE HOSE - INSTALLATION.......19-15
PRESSURE HOSE - REMOVAL..........19-15
PRESSURE LINES - INSTALLATION, HIGH . . 14-7
PRESSURE LINES - REMOVAL, HIGH......14-6
PRESSURE LOSS - STANDARD
PROCEDURE, DETERMINING
CYLINDER............................9-4
PRESSURE PUMP - DESCRIPTION, HIGH . . . 14-7
PRESSURE PUMP - DESCRIPTION, LOW . . . 14-7
PRESSURE PUMP - INSTALLATION,
HIGH..............................14-10
PRESSURE PUMP - INSTALLATION, LOW . 14-11
PRESSURE PUMP - OPERATION, LOW.....14-8
PRESSURE PUMP - REMOVAL, HIGH......14-8
PRESSURE PUMP - REMOVAL, LOW......14-9
PRESSURE SENSOR - DESCRIPTION,
BOOST.............................14-17
PRESSURE SENSOR - DIAGNOSIS AND
TESTING, BOOST.....................14-18
PRESSURE SENSOR - INSTALLATION,
BOOST.............................14-18
PRESSURE SENSOR - OPERATION,
BOOST.............................14-18
PRESSURE SENSOR - REMOVAL, BOOST . . 14-18
PRESSURE SOLENOID - DESCRIPTION,
FUEL..............................14-27
PRESSURE SOLENOID - INSTALLATION,
FUEL..............................14-28
PRESSURE SOLENOID - OPERATION,
FUEL..............................14-27
PRESSURE SOLENOID - REMOVAL, FUEL . 14-28
PRESSURE TRANSDUCER -
DESCRIPTION, A/C...................24-13
PRESSURE TRANSDUCER - DIAGNOSIS
AND TESTING, A/C...................24-13
PRESSURE TRANSDUCER -
INSTALLATION, A/C
...................24-14
PRESSURE TRANSDUCER - OPERATION,
A/C
................................24-13
PRESSURE TRANSDUCER - REMOVAL,
A/C
................................24-14
PRESSURES - DESCRIPTION, TIRE
INFLATION
...........................22-7
PROP ROD - INSTALLATION
............23-52
12 INDEXVA
Description Group-Page Description Group-Page Description Group-Page