2005 MERCEDES-BENZ CLK500 COUPE lock

402 Practical hintsReplacing batteries in the SmartKey/SmartKey with KEYLESS-GO*If the batteries in the SmartKey or the
SmartKey with KEYLESS-GO* are dis-
charged, the vehicle can no longer be
locked or unlocked. It is recommended to
have the batteries replaced at an
authorized Mercedes-Benz Center.
Batteries contain materials that can harm
the environment if disposed of improperly.
Recycling of batteries is the preferred
method of disposal. Many states require
sellers of batteries to accept old batteries
for recycling.
SmartKey
Replacement batteries: Lithium, type
CR 2025 or equivalent.
Remove mechanical key1
(page 397).
1Mechanical key
2Battery compartment

Insert mechanical key 1 in side
opening and push gray slide.
Battery compartment2 is unlatched.

Pull battery compartment 2 out of the
SmartKey housing in direction of
arrow.
Warning!
G
Keep the batteries out of reach of children.
If a battery is swallowed, seek medical help
immediately.
iWhen inserting the batteries, make
sure they are clean and free of lint.iWhen changing batteries, always re-
place both batteries.
The required replacement batteries are
available at any Mercedes-Benz
Center.

403 Practical hints
Replacing batteries in the SmartKey/SmartKey with KEYLESS-GO*

Remove the batteries.
3Battery
4Contact spring

Using a lint-free cloth, insert new
batteries 3 under the contact
spring4 with the plus (+) side facing
up.

Return battery compartment 2 into
housing until it locks into place.

Slide mechanical key 1 back into the
SmartKey.

Check the operation of the SmartKey.
SmartKey with KEYLESS-GO*
Replacement batteries: Lithium, type
CR 2025 or equivalent.
Remove mechanical key (
page 397).

Insert the mechanical key in side open-
ing and push grey slide.
The battery compartment is unlatched.

Pull the battery compartment out of the
SmartKey housing.
1Battery
2Tilt battery up
3Mechanical key

Using mechanical key3, apply
pressure to position2.
Battery1 tilts up slightly.

Pull batteries1 out in direction of
arrow.

Using a lint-free cloth, insert new
batteries1 with the plus (+) side
facing up.

Return battery compartment into hous-
ing until it locks into place.

Slide mechanical key 3 back into the
SmartKey.

Check the operation of the SmartKey
and the KEYLESS-GO*.

406 Practical hintsReplacing bulbsReplacing bulbs for front lamps
Before you start to replace a bulb for a
front lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 124).

Open the hood (
page 308) (except
for side marker lamps).
Front lamps halogen-type
1Housing cover for low beam headlamp
2Housing cover for high beam head-
lamp, parking and standing lamp3Bulb socket for turn signal lamp bulb
4Bulb holder of low beam bulb
5Bulb holder of high beam bulb
6Bulb socket for parking and standing
lamp bulbLow beam bulb

Turn housing cover1 counterclock-
wise and remove it.

Turn bulb holder4 with the bulb coun-
terclockwise and remove it.

Pull the bulb at its socket out of bulb
holder4.

Insert the new bulb so that its socket
locates in the recess of bulb holder4
and is level to it.

Reinsert bulb holder4 with the bulb in
the lamp and turn clockwise.

Align housing cover1 and turn it
clockwise.

407 Practical hints
Replacing bulbs
High beam bulb
Turn housing cover2 counterclock-
wise and remove it.

Turn bulb holder5 with the bulb coun-
terclockwise and remove it.

Pull the bulb at its socket out of bulb
holder5.

Insert the new bulb so that its socket
locates in the recess of bulb holder5
and is level to it.

Reinsert bulb holder5 with the bulb in
the lamp and turn clockwise.

Align housing cover2 and turn it
clockwise.Front turn signal lamp bulb

Turn bulb socket3 counterclockwise
and remove it.

Press gently onto the bulb and turn
counterclockwise out of bulb
socket3.

Press the new bulb gently into bulb
socket3 and turn clockwise until it
engages.

Place bulb socket3 back into the
lamp and turn it clockwise.Parking and standing lamp bulb

Turn housing cover2 counterclock-
wise and remove it.

Pull out bulb socket6 with the bulb.

Pull the bulb out of the bulb socket6.

Press the new bulb into bulb socket6.

Press bulb socket6 back into the
lamp.

Align housing cover2 and turn it
clockwise.

408 Practical hintsReplacing bulbsFront lamps Bi-Xenon*-type
1Bulb socket for turn signal lamp
2Housing cover for high beam flasher,
parking and standing lamp
3Housing cover for Bi-Xenon* headlamp4Bulb holder for high beam flasher bulb
5Bulb socket for parking and standing
lamp bulbHigh beam bulb for high beam flasher

Turn housing cover2 counterclock-
wise and remove it.

Turn bulb holder4 with the bulb coun-
terclockwise and remove it.

Pull the bulb at its socket out of bulb
holder4.

Insert the new bulb so that its socket
locates in the recess of bulb holder4
and is level to it.

Reinsert bulb holder4 with the bulb in
the lamp and turn clockwise.

Align housing cover2 and turn it
clockwise.
Warning!
G
Do not remove the cover
3
for the Bi-Xe-
non* headlamp. Because of high voltage in
xenon lamps, it is dangerous to replace the
bulb or repair the lamp and its components.
We recommend that you have such work
done by a qualified technician.

409 Practical hints
Replacing bulbs
Front turn signal lamp bulb
Turn bulb socket1 counterclockwise
and remove it.

Press gently onto the bulb and turn
counterclockwise out of bulb
socket1.

Press the new bulb gently into bulb
socket1 and turn clockwise until it
engages.

Place bulb socket1 back into the
lamp and turn it clockwise.Parking and standing lamp bulb

Turn housing cover2 counterclock-
wise and remove it.

Pull out bulb socket5 with the bulb.

Pull the bulb out of the bulb socket5.

Press the new bulb into bulb socket5.

Press bulb socket5 back into the
lamp.

Align housing cover2 and turn it
clockwise.Side marker lamp bulb

Carefully slide the lamp towards the
rear in direction of arrows.

Remove front end first.

Turn the bulb socket with the bulb
counterclockwise and remove it.

Pull the bulb out of the bulb socket.

Insert the new bulb into the bulb
socket.

Place the bulb socket back into the
lamp and turn it clockwise.

To reinstall the lamp, set rear end in the
bumper and let the front end engage.

410 Practical hintsReplacing bulbsReplacing bulbs for rear lamps
Before you start to replace a bulb for a rear
lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 124).
Tail lamp unit

Open trunk lid.

Swing the trim panel covering the cor-
responding rear lights to the side.
1Tab

Press tabs1 together.

Remove the bulb carrier.

Press gently onto the respective bulb
and turn counterclockwise out of its
bulb socket.

Press the new bulb gently into its bulb
socket and turn clockwise until it
engages.
1Brake lamp
2Turn signal lamp
3Backup lamp
4Standing and side marker lamp
5Rear fog lamp (driver’s side)/tail

Reinstall the bulb carrier.
Let tabs1 engage.

Reinstall trim panel.License plate lamp
1Screws

Loosen both screws1.

Remove the license plate lamp.

Replace the tubular lamp.

Reinstall the license plate lamp.

Retighten the screws1.

411 Practical hints
Replacing wiper blades
Replacing wiper blades
Removing wiper blades
Remove SmartKey from starter switch.

Fold the wiper arm forward.1Unlock
2Lock

Pull the tab in direction of arrow1 and
remove windshield wiper.
Installing wiper blades
Slide the wiper blade into the cutout on
the wiper arm (see arrows).

Slide the tab back in the direction of
arrow2 until it audibly engages.

Fold the wiper arm backward to rest on
the windshield. Make sure you hold on
to the wiper when folding the wiper arm
back.
Warning!
G
For safety reasons, switch off wipers and
remove SmartKey from starter switch
(vehicles with KEYLESS-GO*: make sure the
vehicle’s on-board electronics have
status
0) before replacing a wiper blade.
Otherwise, the wiper motor could suddenly
turn on and cause injury.
!Never open the hood when the wiper
arms are folded forward.
Hold on to the wiper when folding the
wiper arm back. If released, the force
of the impact from the tensioning
spring could crack the windshield.
Do not allow the wiper arms to contact
the windshield glass without a wiper
blade inserted.
Make certain that the wiper blades are
properly installed. Improperly installed
wiper blades may cause windshield
damage.
For your convenience, we recommend
that you have this work carried out by
an authorized Mercedes-Benz Center.