Page 630 of 969
A87557
A86389
Push
- EMISSION CONTROLCHARCOAL CANISTER ASSY (3MZ-FE)
12-17
2078 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
14. REMOVE FUEL EMISSION TUBE FUEL HOSE
(a) Remove the fuel emission tube fuel hose.
15. INSTALL FUEL EMISSION TUBE FUEL HOSE
16. INSTALL CHARCOAL CANISTER ASSY
(a) Install the charcoal canister with the 2 bolts.
Torque: 40 NVm (400 kgfVcm, 29 ftVlbf)
(b) Connect the fuel tank vent hose.
(1) Push in the quick connector to the pipe until the
quick connector makes a ºclickº sound.
NOTICE:
Check the connected part for damage or foreign ob-
jects.
After connecting, check if the quick connector and
pipe are securely connected by pulling on them.
(c) Connect the fuel hose No. 1.
(d) Install the 3 wire harness clamps.
(e) Connect the VSV connector.
17. INSTALL FUEL TANK ASSY (See page 11-28)
18. INSTALL FUEL TANK PROTECTOR LOWER CENTER (See page 11-28)
19. INSTALL PARKING BRAKE CABLE ASSY NO.3 (See page 11-28)
20. INSTALL PARKING BRAKE CABLE ASSY NO.2 (See page 11-28)
21. INSTALL EXHAUST PIPE ASSY CENTER (See page 11-28)
22. INSTALL FUEL SUCTION W/ PUMP & GAUGE TUBE ASSY (See page 11-20)
23. CONNECT ENGINE WIRE NO. 3 (BATTERY NEGATIVE TERMINAL)
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
24. ADD FUEL
25. CHECK FOR FUEL LEAKS (See page 11-5)
26. CHECK FOR EXHAUST GAS LEAKS
27. INSTALL REAR FLOOR SERVICE HOLE COVER (See page 11-20)
28. INSTALL REAR SEAT CUSHION ASSY
29. INSTALL FLOOR PANEL BRACE REAR (See page 15-2)
30. SYSTEM INITIALIZATION (See page 19-15)
Page 633 of 969
120BV-02
A91017
Nylon Tube Fuel Tube Joint
O-ring
Tube Joint Clip Fuel Suction Plate
A79488
Tube Joint Clip
A79489
A79491
Cover
Tube Joint Clip
12-20
- EMISSION CONTROLVAPOR PRESSURE SENSOR ASSY (3MZ-FE)
2081 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
VAPOR PRESSURE SENSOR ASSY (3MZ-FE)
REPLACEMENT
1. DISCHARGE FUEL SYSTEM PRESSURE (See page 11-1)
2. DISCONNECT ENGINE WIRE NO. 3 (BATTERY NEGATIVE TERMINAL)
3. REMOVE REAR SEAT CUSHION ASSY (See page 72-39)
4. REMOVE REAR FLOOR SERVICE HOLE COVER (See page 11-20)
5. DISCONNECT FUEL PUMP TUBE SUB-ASSY
(a) Remove the tube joint clip, then pull out the fuel pump
tube.
NOTICE:
Check around the quick connector for dirt or mud be-
fore this operation. Remove the dirt if necessary.
Be careful of mud because the quick connector has
an O-ring which seals the pipe and quick connector
that can be contaminated.
Do not use any tools in this operation.
Do not bend or twist the nylon tube. Protect the quick
connector by covering it with a vinyl or plastic bag.
When the pipe and quick connector are stuck, push
and pull the quick connector to release. Pull the quick
connector carefully.
6. REMOVE FUEL TANK VENT TUBE SET PLATE
(a) Remove the 8 bolts, then remove the fuel tank vent tube
set plate.
7. REMOVE VAPOR PRESSURE SENSOR ASSY
(a) Remove the cover.
(b) Remove the tube joint clip, then pull out the vapor pres-
sure sensor.
Page 634 of 969
A86272
Cover
Tube Joint Clip
A79489Mark
A81595
Tube Joint ClipCollar
- EMISSION CONTROLVAPOR PRESSURE SENSOR ASSY (3MZ-FE)
12-21
2082 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
8. INSTALL VAPOR PRESSURE SENSOR ASSY
(a) Install the vapor pressure sensor with the tube joint clip.
NOTICE:
Check the connected part for scratch or foreign ob-
jects.
Check that the vapor pressure sensor is inserted se-
curely.
Check that the tube joint clip is on the collar of the va-
por pressure sensor.
After installing the tube joint clip, check that the vapor
pressure sensor has not been pulled off.
(b) Install the cover.
9. INSTALL FUEL TANK VENT TUBE SET PLATE
(a) Align the mark of the fuel tank vent tube set plate with the
fuel suction tube w/ pump & gauge.
(b) Install the fuel tank vent tube set plate with the 8 bolts.
Torque: 5.9 NVm (60 kgfVcm, 52 in.Vlbf)
10. CONNECT FUEL PUMP TUBE SUB-ASSY
(a) Install the fuel pump tube with the tube joint clip.
NOTICE:
Check the connected part for scratch or foreign ob-
jects.
Check that the fuel tube joint is inserted securely.
Check that the tube joint clip is on the collar of the fuel
tube joint.
After installing the tube joint clip, check that the fuel
tube joint has not been pulled off.
11. CONNECT ENGINE WIRE NO. 3 (BATTERY NEGATIVE TERMINAL)
Torque: 5.4 NVm (55 kgfVcm, 48 in.Vlbf)
12. CHECK FOR FUEL LEAKS (See page 11-5)
13. INSTALL REAR FLOOR SERVICE HOLE COVER (See page 11-20)
14. INSTALL REAR SEAT CUSHION ASSY
15. SYSTEM INITIALIZATION (See page 19-15)
Page 723 of 969
51067-03
F41916
TYPE A VANE PUMP
TYPE B VANE PUMP Pulley
Pulley
- POWER STEERINGPOWER STEERING SYSTEM
51-1
2576 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
POWER STEERING SYSTEM
PRECAUTION
1. HANDLING PRECAUTIONS ON STEERING SYSTEM
(a) Care must be taken to when replacing parts. Incorrect re-
placement could affect the performance of the steering
system and result in a driving hazard.
(b) 1MZ-FE engine has 2 types of vane pump assy.
HINT:
TYPE A VANE PUMP
Vane pump pulley can be removed from the vane pump shaft
(See page 51-7).
TYPE B VANE PUMP
Vane pump pulley cannot be removed from the vane pump
shaft (See page 51-7).
2. HANDLING PRECAUTIONS ON SRS AIRBAG SYSTEM
(a) The LEXUS ES330 is equipped with SRS (Supplemental Restraint System) such as the driver airbag
and front passenger airbag. Failure to carry out service operation in correct sequence could cause the
SRS to unexpectedly deploy during servicing, possibly leading to a serious accident. Before servicing
(including removal or installation of parts, inspection or replacement), be sure to read the precaution-
ary notice for the supplemental restraint system (See page 60-1).
Page 737 of 969
F41573
F41492
- POWER STEERINGVANE PUMP ASSY
51-15
2590 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
37. INSTALL VANE PUMP HOUSING REAR
(a) Coat a new O-ring with power steering fluid and install it to the vane pump housing rear.
(b) Install the vane pump housing rear with the 4 bolts.
Torque: 24 NVm (245 kgfVcm, 18 ftVlbf)
38. MEASURE VANE PUMP ROTATION TORQUE(TYPE A
VANE PUMP)
(a) Check that the vane pump rotates smoothly without ab-
normal noise.
(b) Temporarily install the pulley set nut.
(c) Using a torque wrench, check the vane pump rotating
torque.
Rotating torque:
0.27 NVm (2.8 kgfVcm, 2.4 in.Vlbf) or less
39. MEASURE VANE PUMP ROTATION TORQUE(TYPE B
VANE PUMP)
(a) Check that the vane pump rotates smoothly without ab-
normal noise.
(b) Temporarily install the service bolt.
Recommended service bolt:
Thread diameter: 10 mm (0.39 in.)
Thread pitch: 1.25 mm (0.0492 in.)
Bolt length: 50 mm (1.97 in.)
(c) Using a torque wrench, check the vane pump rotating
torque.
Rotating torque:
0.27 NVm (2.8 kgfVcm, 2.4 in.Vlbf) or less
40. INSTALL VANE PUMP BRACKET REAR(TYPE A VANE PUMP)
(a) Install the vane pump bracket rear with the 2 bolts.
Torque: 43 NVm (438 kgfVcm, 32 ftVlbf)
41. INSTALL VANE PUMP BRACKET REAR(TYPE B VANE PUMP)
(a) Install the vane pump bracket rear with the 2 bolts and 2 nuts.
Torque: 44 NVm (449 kgfVcm, 32 ftVlbf)
42. INSTALL FLOW CONTROL VALVE COMPRESSION SPRING
(a) Coat the flow control valve compression spring with power steering fluid and install it.
(b) Install the flow control valve compression spring.
43. INSTALL FLOW CONTROL VALVE
(a) Coat the flow control valve with power steering fluid.
(b) Install the flow control valve.
44. INSTALL PRESSURE PORT UNION
(a) Coat a new O-ring with power steering fluid and install it to the pressure port union.
(b) Install the pressure port union.
Torque: 83 NVm (846 kgfVcm, 61 ftVlbf)
Page 750 of 969
F40911
SST
C83179
Wire Cylinder End
Stopper
F40542
SST
51-28
- POWER STEERINGRACK & PINION POWER STEERING GEAR ASSY
2603 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
32. REMOVE POWER STEERING CONTROL VALVE
UPPER OIL SEAL
(a) Using SST and a press, remove the control valve upper
bearing and power steering control valve upper oil seal
from the control valve housing.
SST 09950- 70010 (09951- 07150), 09950- 60010
(09951-00250)
33. REMOVE CYLINDER END STOPPER
(a) Using a screwdriver and a hammer, turn the cylinder end
stopper clockwise until the wire end is visible through the
service hole.
(b) Using a screwdriver and a hammer, turn the cylinder end
stopper counterclockwise, and remove the wire and cylin-
der end stopper.
34. REMOVE POWER STEERING RACK
(a) Remove the power steering rack and power steering rack bush.
35. REMOVE POWER STEERING RACK BUSH
(a) Remove the power steering rack bush from the power
steering rack.
(b) Using SST, remove the rack bush oil seal.
SST 09527-2101 1, 09612-24014 (09613-22011)
(c) Using a screwdriver, remove the O-ring from the power
steering rack bush.
Page 782 of 969
190SE-01
A79718
A86236Terminal 50Terminal C
BodyBattery
A86239Terminal CBattery Disconnect
A86238
Disconnect
Body
Battery
- STARTING & CHARGINGSTARTING SYSTEM (3MZ-FE)
19-1
2333 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
STARTING SYSTEM (3MZ-FE)
INSPECTION
1. INSPECT STARTER ASSY
NOTICE:
These tests must be performed within 3 to 5 seconds to
prevent burnout of the coil.
(a) Perform the pull-in test.
(1) Remove the nut, then disconnect the lead wire from
terminal C.
(2) Connect the battery to the repair service starter kit
as shown in the illustration. Check that the clutch
pinion gear is extended.
If the clutch pinion gear does not move, replace the starter mag-
netic switch.
(b) Perform the hold-in test.
(1) Disconnect the negative (-) lead from terminal C
with the lead wire disconnected from terminal C.
Check that the clutch pinion gear remains ex-
tended.
If the clutch pinion gear returns inward, replace the starter mag-
netic switch.
(c) Check the operation.
(1) Disconnect the negative (-) lead from the switch
body. Check that the clutch pinion gear returns.
If the clutch pinion gear does not return inward, replace the
starter magnetic switch.
Page 810 of 969
5002J-08
- STEERING COLUMNSTEERING
50-1
2562 Author: Date:
STEERING
PRECAUTION
1. HANDLING PRECAUTIONS ON STEERING SYSTEM
(a) Care must be taken when replacing parts. Incorrect replacement they could affect the performance
of the steering system and result in a driving hazard.
2. HANDLING PRECAUTIONS ON SRS AIRBAG SYSTEM
(a) The LEXUS ES330
is equipped with SRS (Supplemental Restraint System) such as the driver airbag
and front passenger airbag. Failure to carry out service operation in correct sequence could cause the
SRS to unexpectedly deploy during servicing, possibly leading to a serious accident. Before servicing
(including removal or installation of parts, inspection or replacement), be sure to read the precaution-
ary notice for the supplemental restraint system (See page 60-1).
