2005 LEXUS ES300 tow

IRON PARTICLE RUST CONTAMINATION REPAIR ± PA001-05 January 12, 2005
Page 2 of 2
WARNING:
Auto Magic

Special Cleaner Concentrate is a corrosive material. Appropriate
personal protection equipment must be worn to protect persons performing the
contamination removal procedure. Please refer to the precautions on the product prior
to use.
CAUTION:
Consult local or state regulations regarding the handling, use, and disposal of Auto
Magic

Special Cleaner Concentrate prior to use.
Under no circumstances should contamination removal be performed in direct
sunlight or contamination removal solution be allowed to dry on vehicle surfaces, as
staining of plastic, rubber, or painted parts may result.
1. Move vehicle out of direct sunlight. Initially rinse with cool water then wash with liquid
car wash detergent. Rinse again thoroughly with fresh water.
2. Dilute the mixture to a 1:8 ratio for painted surfaces. Use the recommended dilution
ratio when applying to any other surface. Apply the diluted cleaner concentrate so
that it evenly covers the affected area. Use an appropriate mitt or sponge to agitate
the surface.
3. Thoroughly rinse vehicle with fresh water.
4. Inspect vehicle carefully both visually and by feel to determine if all iron particles
have been removed. Repeat the wash several times if necessary to achieve
complete removal.
5. Dry vehicle with a soft terry cloth towel and apply a non±abrasive, non±silicone glaze
to obtain a high±gloss finish.
General
Precautions
Repair
Procedure

Lexus Supports ASE CertificationPage 1 of 9
Title:
PRE-DELIVERY SERVICE (PDS)
INFORMATION FOR ES 330
Models:
'04 ES 330
Technical Service
Information Bulletin
August 26, 2003
PD002-03
The following items need to be performed during Pre±Delivery Service (PDS) on
2004 model year ES 330 vehicles.
2004 model year ES 330 vehicles.
ITEM NO.SUBJECTPAGE
1D.C.C. Fuse Installation During PDS2
2Removal of Front Emergency Towing Eyelet and Installation
of Towing Eyelet Hole Cover (Performed at Port)3
3Front License Plate Mounting Bracket Installation4
4Initialization of Moon Roof5
5Initial Calibration of Compass6
6Installation of Rubber Body Plugs9
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
PRE±DELIVERY SERVICE
Introduction
Applicable
Vehicles
Contents
Warranty
Information

PRE±DELIVERY SERVICE (PDS) INFORMATION FOR ES 330 ± PD002-03 August 26, 2003
Page 3 of 9
REMOVAL OF FRONT EMERGENCY TOWING EYELET AND INSTALLATION OF
TOWING EYELET HOLE COVER (PERFORMED AT PORT)
1. Remove the emergency towing eyelet
from the front bumper by turning
counterclockwise.
NOTE:
If it is hard to loosen the emergency
towing eyelet, use a steel bar.
2. Place the removed emergency
towing eyelet in the tool tray in the
luggage compartment.
3. Install the front towing eyelet hole
cover which is stored in the glove box
onto the front bumper as shown in
the diagram. ITEM NO. 2:
Emergency Towing Eyelet
Installation
Procedure

PRE±DELIVERY SERVICE (PDS) INFORMATION FOR ES 330 ± PD002-03 August 26, 2003
Page 8 of 9
INITIAL CALIBRATION OF COMPASS (Continued)
3. Check that the direction appears
several seconds after adjustment.
4. Start the engine and push the switch
for about 6 seconds until ªCº appears
on the display.
5. Drive the vehicle slowly at 5 mph, or
less, in a circle until the direction is
displayed. If there is not enough space
to drive in a circle, drive around the
block until the direction is displayed.
After driving in circles 1 to 3 times,
calibration is complete with the direction
shown on the display.
NOTE:
Do not perform calibration of the compass in a place where the earth's magnetic
field is subject to interference by artificial magnetic fields (underground parking,
under a steel tower, between buildings, roof parking, near a railroad crossing, near
a large vehicle, etc.)
During calibration, do not operate electric systems (moon roof, power windows,
etc.) as they may interfere with the calibration.
ITEM NO. 5:
Compass
Calibration
Procedure
(Continued)

INITIAL CALIBRATION OF COMPASS DURING PDS ± PD034-05 August 22, 2005
Page 3 of 3
3. Check that the direction appears
several seconds after adjustment.
4. Start the engine and push the switch
for about 6 seconds until ªCº appears
on the display.
5. Drive the vehicle slowly at 5 mph
(8 km/h), or less, in a circle until the
direction is displayed. If there is not
enough space to drive in a circle,
drive around the block until the
direction is displayed.
After driving in 1 to 3 circles,
calibration is complete with the
direction shown on the display.
NOTE:
Do NOT perform calibration of the compass in a place where the Earth's magnetic
field is subject to interference by artificial magnetic fields (underground parking,
under a steel tower, between buildings, roof parking, near a railroad crossing, near
a large vehicle, etc.)
During calibration, do NOT operate electric systems (moon roof, power windows,
etc.) as they may interfere with the calibration. Compass
Calibration
Procedure
(Continued)

Lexus Supports ASE CertificationPage 1 of 2
Title:
FRONT EMERGENCY TOWING EYELET &
EYELET HOLE COVER
Models:
'05 ± '06 ES 330
Technical Service
Information Bulletin
August 26, 2005
PD037-05
The 2005 ± 2006 model year ES 330 is shipped with a front emergency towing eyelet.
Follow the procedure below to remove the eyelet and save for customer use.
2005 ± 2006 model year ES 330 vehicles.
OP CODEDESCRIPTIONTIMEOFPT1T2
N/ANot Applicable to Warranty±±±±
1. Remove the emergency towing
eyelet from the front bumper by
turning counterclockwise.
NOTE:
If it is hard to loosen the emergency
towing eyelet, use a steel bar.
PRE-DELIVERY SERVICE
Introduction
Applicable
Vehicles
Warranty
Information
Emergency Towing Eyelet
Installation
Procedure

FRONT EMERGENCY TOWING EYELET & EYELET HOLE COVER ± PD037-05 August 26, 2005
Page 2 of 2
2. Place the emergency towing
eyelet in the tool tray in the
luggage compartment.
3. Install the front towing eyelet hole
cover, which is stored in the glove
box, onto the front bumper as shown
in the illustration.Installation
Procedure
(Continued)