2005 KIA Rio ignition

Driving Your Vehicle4-26 Fuel GaugeThe fuel gauge indicates the approximate amount of
fuel remaining in the fuel tank.
Fuel tank capacity: 45 L (11.7 US gal.)
The fuel gauge is supplemented by a low fuel warning
light located in the instrument panel.
This gauge is designed to continue indicating the
amount of fuel remaining in the fuel tank even after the
ignition switch has been turned to OFF.
Engine Temperature GaugeThis gauge shows the temperature of the engine
coolant when the ignition switch is ON.
If the gauge pointer moves beyond the normal range
area toward the H position, it indicates overheating that
may damage the engine.
Do not continue driving with an overheated engine.
If your vehicle overheats, refer to “Overheating’’ in the
Index.
1B3105005
1B3105006
With Tachometer
Without Tachometer
With Tachometer
Without Tachometer
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 26

4-27 Instrument Panel Illumination (If equipped)
When the vehicle’s parking lights or headlights are
ON, rotate the illumination control knob to adjust the
instrument panel illumination intensity.
Warnings and IndicatorsWarning Lights/Audible IndicatorsChecking Operation
All the warning lights are checked by turning the igni-
tion switch ON (you do not need to start the engine).
Any light that does not come ON should be checked
by an Authorized Kia Dealer.
After starting the engine, check to make sure that all
warning lights are OFF. If any are still ON, this indi-
cates a situation that needs attention. When releasing
the parking brake, the brake system warning light
should go OFF.Parking Brake and Brake Fluid
Warning Parking Brake Warning
This light comes ON when the parking brake is applied
with the ignition switch in the START or ON position.
The warning light should go OFF when the parking
brake is released.
2FDA407
BRAKE
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 27

Driving Your Vehicle4-28Low Brake Fluid Level Warning
If the warning light remains ON when the parking
brake is released, it may indicate that the brake fluid
level in the reservoir is low.
If the warning light remains ON:
1. Drive to the nearest safe location and carefully stop
your vehicle.
2. With the engine stopped, check the brake fluid level
immediately and add fluid as required. All brake
components should also be checked immediately
for fluid leaks.
3. If leaks are found, if the warning light remains ON,
or if the brakes do not operate properly, do not
drive the vehicle. Have it towed to an Authorized
Kia Dealer for a brake system inspection and nec-
essary repairs.To check bulb operation, the warning light illuminates
when the ignition switch is in the ON position.
Safety Belt Warning As a reminder to the driver and passenger, safety belt
warning light will illuminate for approximately 6 sec-
onds each time you turn the ignition switch ON.
If the driver’s lap/shoulder belt is not fastened when
the key is turned ON, a chime sounds for approximate-
ly six seconds and the safety belt warning light illumi-
nates for approximately six seconds. If the system does
not operate as described, see an Authorized Kia Dealer
for assistance.Air Bag Warning This warning light will remain ON for approximately
6 seconds each time you turn the ignition switch ON.
If the system does not operate as described or if the
light comes on while the vehicle is being driven, see an
Authorized Kia Dealer for immediate assistance.Charging System Warning This warning light indicates a malfunction of either the
generator or electrical charging system.
–
+
WARNING - Brake Warning
Lights
Driving the vehicle with a warning light ON is
dangerous. If the brake warning light remains
ON, have the brakes checked and repaired
immediately.
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 28

Driving Your Vehicle4-32Key Reminder Warning Chime
If the driver’s door is opened and the ignition key is
left in the ignition switch, the key reminder warning
chime will sound. This is to remind you to remove
your keys from the ignition before you lock the vehi-
cle.Lights-On Warning ChimeThe lights-on warning chime will sound if the head-
light switch is left in the 1st or 2nd position and the
door is opened.Headlight High Beam Indicator This indicator illuminates when the headlights are on
and in the high beam position or when the turn signal
lever is pulled into the Flash-to-Pass position.O/D OFF Indicator
(automatic transaxle)This indicator comes on when the O/D system is
deactivated.
✽
NOTICE
A loose fuel filler cap may cause the On Board
DiagnosticSystem Malfunction Indicator Light
( ) in the instrument panel to illuminate
unnecessarily. Always make sure that the fuel
filler cap is tight.
CHECK
CHECK
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 32

4-33 Door Ajar Warning
This warning light comes on when a door is not closed
securely with the ignition switch in any position.Anti-Lock Brake System (ABS)
Warning Light (if equipped)This light illuminates when you start the engine. The
light will go off if the ABS system is operating nor-
mally. Also, this light comes on if the key is turned to
ON, and then goes off in 2-3 seconds if the system is
operating normally.
If this warning light illuminates while the vehicle is
being driven, have the vehicle checked by an autho-
rized Kia Dealer as soon as possible.Rear Window Defroster Indicator This light comes on when the rear defroster is ON.Rear Hatch Warning Light
(5 door-if equipped)This warning light comes on when a rear hatch is not
closed securely with the ignition switch in any posi-
tion.
AS2B04020
LightingLighting ControlTo turn the lights on, twist the knob on the end of the
control lever which is located on the steering column
to the left of the steering wheel.
First position
Tail, parking, license and sidemarker lights and instru-
ment panel lights ON.
Second position
Head, tail, parking, license and sidemarker lights and
instrument panel lights ON.
ABS
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 33

4-35 Turn Signals
The same lever that controls the headlights also con-
trols the turn signals.
The ignition switch must be ON for the turn signals
to function. Move the lever up or down to activate the
turn signals. The turn signals will self-cancel after a
turn is completed. If the indicator continues to flash
after a turn, manually return the lever to the OFF (mid-
dle) position.
Lane Change Signals
To signal a lane change, move the turn signal lever
slightly and hold it in position. The lever will return to
the OFF (middle) position when released.
Green arrow indicators on the instrument panel indi-
cate which turn signal is operating. If an indicator
stays ON and does not flash or if it flashes abnormally,
one or more of the turn signal bulbs may be burned out
and will require replacement.Daytime Running Lights (DRL)Daytime Running Lights (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving condi-
tions, but they can be especially helpful in the short
periods after dawn and before sunset. The DRL system
will make your low-beam headlights turn OFF when:
 The headlight switch is ON.
 The parking brake is engaged.
 The engine stops.
AS2B04023
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 35

Driving Your Vehicle4-36
One-Touch Wipers
For a single wiping cycle, push the lever forward and
release it with the lever in the OFF position.
✽
NOTICE
 To prevent possible damage to the wipers or
windshield, do not operate the wipers when the
windshield is dry.
 To prevent damage to the wiper blades, do not
use gasoline, kerosene, paint thinner, or other
solvents on or near them.
 To prevent damage to the wiper arms and other
components, do not attempt to move the wipers
manually.
4-36
Wipers and WashersWindshield WipersThe ignition switch must be ON.
To turn the wipers ON, pull the windshield wiper con-
trol lever down.
INT – Intermittent wiper operation
1 – Normal wiper speed
2 – Fast wiper speed
1T21030111T2103013B
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 36

4-37 Windshield Washers
The ignition switch must be ON for the washer system
to operate. Pull the lever toward you and hold it to acti-
vate the washer. The wiper will automatically turn on
and wipe for 1 to 3 cycles after the lever is released.
1T2103013C
If the washer does not work, check the washer fluid
level. If the fluid level is not sufficient, add an appro-
priate, non-abrasive, windshield washer fluid to the
washer reservoir. The reservoir filler neck is located in
the front of the engine compartment, on the passen-
ger’s side.
CAUTION
Do not use the washer in freezing temperatures
without first warming the windshield with the
defrosters; the washer solution could freeze on
contact with the windshield and obscure your
vision.✽
NOTICE
To prevent possible damage to the washer pump,
do not operate the washer when the fluid reservoir
is empty.
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 37