2005 INFINITI QX4 transmission oil

AT-70
TROUBLE DIAGNOSIS
Revision: October 20052005 QX56
30
Slips/Will
Not
engageNo shock at all or the
clutch slips when
vehicle changes
speed D
4 → D5 .ON vehicle1. Fluid level and stateAT-5 0
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 3
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 6 0,
AT- 1 4 4
4. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 6 4,
AT- 1 4 8
5. CAN communication lineAT-9 5
6. Line pressure testAT-5 1
7. Control valve with TCMAT- 2 3 1
OFF vehicle8. Torque converterAT- 2 6 2
9. Oil pump assemblyAT- 2 8 0
10. Front brake (brake band)AT- 2 6 2
11. Input clutchAT- 2 8 4
12. Gear systemAT- 2 5 0
13. High and low reverse clutchAT- 2 9 4
31When you press the
accelerator pedal and
shift speed D5 → D4
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT-5 0
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 3
3. ATF pressure switch 1 and front brake solenoid valveAT- 1 6 0,
AT- 1 4 4
4. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 6 4,
AT- 1 4 8
5. CAN communication lineAT-9 5
6. Line pressure testAT-5 1
7. Control valve with TCMAT- 2 3 1
OFF vehicle8. Torque converterAT- 2 6 2
9. Oil pump assemblyAT- 2 8 0
10. Input clutchAT- 2 8 4
11. Gear systemAT- 2 5 0
12. High and low reverse clutchAT- 2 9 4
13. Direct clutchAT- 2 9 6
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-71
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
32
Slips/Will
Not
engageWhen you press the
accelerator pedal and
shift speed D4 → D3
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT- 5 0
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 3
3. ATF pressure switch 3 and input clutch solenoid valveAT- 1 6 2,
AT- 1 4 0
4. ATF pressure switch 1 and front brake solenoid valveAT- 1 6 0,
AT- 1 4 4
5. CAN communication lineAT- 9 5
6. Line pressure testAT- 5 1
7. Control valve with TCMAT- 2 3 1
OFF vehicle8. Torque converter AT- 2 6 2
9. Oil pump assemblyAT- 2 8 0
10. 3rd one-way clutchAT- 2 8 2
11. Gear systemAT- 2 5 0
12. High and low reverse clutchAT- 2 9 4
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 6
, AT-1 7 .)AT- 2 6 2
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 6
, AT- 1 7
.)AT- 2 6 2
33When you press the
accelerator pedal and
shift speed D3 → D2
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT- 5 0
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 3
3. ATF pressure switch 6, high and low reverse clutch sole-
noid valveAT- 1 6 6,
AT- 1 5 2
4. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 6 4,
AT- 1 4 8
5. CAN communication lineAT- 9 5
6. Line pressure testAT- 5 1
7. Control valve with TCMAT- 2 3 1
OFF vehicle8. Torque converterAT- 2 6 2
9. Oil pump assemblyAT- 2 8 0
10. 3rd one-way clutchAT- 2 8 2
11. Gear systemAT- 2 5 0
12. Direct clutchAT- 2 9 6
13. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 6
, AT- 1 7
.)AT- 2 6 2
No. Items Symptom Condition Diagnostic ItemReference
page

AT-72
TROUBLE DIAGNOSIS
Revision: October 20052005 QX56
34
Slips/Will
Not
EngageWhen you press the
accelerator pedal and
shift speed D2 → D1
the engine idles or the
transmission slips.ON vehicle1. Fluid level and stateAT-5 0
2. Vehicle speed sensor A/T and vehicle speed sensor MTRAT- 1 0 8,
AT- 1 3 3
3. ATF pressure switch 5 and direct clutch solenoid valveAT- 1 6 4,
AT- 1 4 8
4. CAN communication lineAT-9 5
5. Line pressure testAT-5 1
6. Control valve with TCMAT- 2 3 1
OFF vehicle7. Torque converterAT- 2 6 2
8. Oil pump assemblyAT- 2 8 0
9. 3rd one-way clutchAT- 2 8 2
10. 1st one-way clutchAT- 2 8 9
11. Gear systemAT- 2 5 0
12. Reverse brakeAT- 2 6 2
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-1 6
, AT-1 7 .)AT- 2 6 2
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-1 6
, AT- 1 7
.)AT- 2 6 2
35With selector lever in
“D” position, accelera-
tion is extremely poor.ON vehicle1. Fluid level and stateAT-5 0
2. Line pressure testAT-5 1
3. Accelerator pedal position sensorAT- 1 2 3
4. CAN communication lineAT-9 5
5. PNP switchAT- 1 0 4
6. Control cable adjustmentAT- 2 2 8
7. Control valve with TCMAT- 2 3 1
OFF vehicle8. Torque converterAT- 2 6 2
9. Oil pump assemblyAT- 2 8 0
10. 1st one-way clutchAT- 2 8 9
11. Gear systemAT- 2 5 0
12. Reverse brakeAT- 2 6 2
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-1 6
, AT-1 7 .)AT- 2 6 2
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-1 6
, AT- 1 7
.)AT- 2 6 2
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS
AT-79
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
56
OthersMaximum speed low.ON vehicle1. Fluid level and stateAT- 5 0
2. Line pressure testAT- 5 1
3. Accelerator pedal position sensorAT- 1 2 3
4. CAN communication lineAT- 9 5
5. Direct clutch solenoid valveAT- 1 4 8
6. Control valve with TCMAT- 2 3 1
OFF vehicle7. Torque converterAT- 2 6 2
8. Oil pump assemblyAT- 2 8 0
9. Input clutchAT- 2 8 4
10. Gear systemAT- 2 5 0
11. High and low reverse clutchAT- 2 9 4
12. Direct clutchAT- 2 9 6
13. Forward one- way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT- 1 6
, AT-1 7 .)AT- 2 6 2
14 Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT- 1 6
, AT- 1 7
.)AT- 2 6 2
57Extremely large
creep.ON vehicle1. Engine idle speed EC-77

2. CAN communication lineAT- 9 5
3. ATF pressure switch 5AT- 1 6 4
OFF vehicle 4. Torque converterAT- 2 6 2
58With selector lever in
“P” position, vehicle
does not enter parking
condition or, with
selector lever in
another position, park-
ing condition is not
cancelled.
Refer to AT- 1 8 1 , "
In
“P” Position, Vehicle
Moves When Pushed"
.ON vehicle1. PNP switchAT- 1 0 4
2. Control cable adjustmentAT- 2 2 8
OFF vehicle 3. Parking pawl componentsAT- 2 5 0
59Vehicle runs with
transmission in “P”
position.ON vehicle1. PNP switchAT- 1 0 4
2. Fluid level and stateAT- 5 0
3. Control cable adjustmentAT- 2 2 8
4. Control valve with TCMAT- 2 3 1
5. Parking pawl componentsAT- 2 5 0
OFF vehicle 6. Gear systemAT- 2 5 0
No. Items Symptom Condition Diagnostic ItemReference
page

TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-185
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
6. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT-231, "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 6 2 , "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-280, "Oil Pump" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace damaged parts.
7. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT-231, "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 6 2 , "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-280, "Oil Pump" .
–Power train system. Refer to AT- 2 6 2 , "Disassembly" .
–Transmission case. Refer to AT - 2 6 2 , "Disassembly" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace damaged parts.
8. CHECK A/T FLUID CONDITION
1. Remove oil pan. Refer to AT-231, "
Control Valve With TCM and A/T Fluid Temperature Sensor 2" .
2. Check A/T fluid condition. Refer to AT- 1 3 , "
Checking A/T Fluid" .
OK or NG
OK >> GO TO 10.
NG >> GO TO 9.
9. DETECT MALFUNCTIONING ITEM

Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to AT-60,
"Symptom Chart" (Symptom No.1).
OK or NG
OK >> GO TO 10.
NG >> Repair or replace damaged parts.
10. CHECK SYMPTOM
Check again. Refer to AT- 5 4 , "
Check at Idle" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 11.
SCIA5199E

AT-188
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: October 20052005 QX56
5. DETECT MALFUNCTIONING ITEM
1. Disassemble A/T. Refer to AT-262, "
Disassembly" .
2. Check the following items:
–Reverse brake. Refer to AT-262, "Disassembly" .
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
6. CHECK LINE PRESSURE
Check the line pressure with the engine idling. Refer to AT- 5 1 , "
LINE
PRESSURE TEST" .
OK or NG
OK >> GO TO 9.
NG - 1 >> Line pressure high. GO TO 7.
NG - 2 >> Line pressure low. GO TO 8.
7. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 3 1 , "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT-262, "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-280, "Oil Pump" .
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
8. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 3 1 , "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT-262, "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-280, "Oil Pump" .
–Power train system. Refer to AT-262, "Disassembly" .
–Transmission case. Refer to AT-262, "Disassembly" .
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.
SAT4 9 4G

TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-191
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: October 20052005 QX56
5. CHECK LINE PRESSURE
Check line pressure at idle with selector lever in “D” position. Refer
to AT-51, "
LINE PRESSURE TEST" .
OK or NG
OK >> GO TO 8.
NG - 1 >> Line pressure high. GO TO 6.
NG - 2 >> Line pressure low. GO TO 7.
6. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT-231, "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 6 2 , "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-280, "Oil Pump" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace damaged parts.
7. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT-231, "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 6 2 , "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-280, "Oil Pump" .
–Power train system. Refer to AT- 2 6 2 , "Disassembly" .
–Transmission case. Refer to AT - 2 6 2 , "Disassembly" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace damaged parts.
8. CHECK A/T FLUID CONDITION
1. Remove oil pan. Refer to AT-231, "
Control Valve With TCM and A/T Fluid Temperature Sensor 2" .
2. Check A/T fluid condition. Refer to AT- 5 0 , "
Fluid Condition
Check" .
OK or NG
OK >> GO TO 9.
NG >> GO TO 12.
SAT4 9 4G
SCIA5199E

AT-194
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: October 20052005 QX56
7. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 3 1 , "
Control Valve With TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT-262, "
Disassembly" .
3. Check the following items:
–Oil pump assembly. Refer to AT-280, "Oil Pump" .
–Power train system. Refer to AT-262, "Disassembly" .
–Transmission case. Refer to AT-262, "Disassembly" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace damaged parts.
8. CHECK A/T FLUID CONDITION
1. Remove oil pan. Refer to AT-231, "
Control Valve With TCM and A/T Fluid Temperature Sensor 2" .
2. Check A/T fluid condition. Refer to AT- 5 0 , "
Fluid Condition
Check" .
OK or NG
OK >> GO TO 9.
NG >> GO TO 12.
9. DETECT MALFUNCTIONING ITEM

Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to AT-60,
"Symptom Chart" (Symptom No.23).
OK or NG
OK >> GO TO 10.
NG >> Repair or replace damaged parts.
10. CHECK SYMPTOM
Check again. Refer to AT-55, "
Cruise Test - Part 1" , AT-57, "Cruise Test - Part 2" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 11.
11 . PERFORM TCM INSPECTION
1. Perform TCM input/output signals inspection. Refer to AT- 8 2 , "
TCM Input/Output Signal Reference Val-
ues" .
2. If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness
connector.
OK or NG
OK >>INSPECTION END
NG >> Repair or replace damaged parts.
SCIA5199E