2005 INFINITI QX4 check engine

SERVICE DATA AND SPECIFICATIONS (SDS)
ATC-193
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: October 20052005 QX56
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Service Data and Specifications (SDS)EJS003Z9
COMPRESSOR
LUBRICANT
REFRIGERANT
ENGINE IDLING SPEED
Refer to EC-77, "Idle Speed and Ignition Timing Check" .
BELT TENSION
Refer to EM-12, "Checking Drive Belts" .
MakeZEXEL VALEO CLIMATE CONTROL
ModelDKS-17D
Typ eSwash plate
Displacement
175.5 cm
3 (10.7 in3 ) / revolution
Cylinder bore × stroke 30.5 mm (1.20 in) x 24.0 mm (0.94 in)
Direction of rotation Clockwise (viewed from drive end)
Drive beltPoly V
MakeZEXEL VALEO CLIMATE CONTROL
ModelDKS-17D
NameNISSAN A/C System Lubricant Type S
Capacity
290 m (9.8 US fl oz, 10.2 Imp fl oz)
Typ eHFC 134a (R-134a)
Capacity1.08 ± 0.05 kg (2.38 ± 0.11 oz)

AV-2Revision: October 20052005 QX56 “VIEW” MODE ..................................................... 70
“HEADING” MODE .............................................. 71
“NEARBY DISPLAY ICONS” MODE ................... 71
“SAVE CURRENT LOCATION” MODE ............... 71
“ADJUST CURRENT LOCATION” MODE ........... 71
“AUTO RE-ROUTE” MODE ................................. 72
“AVOID AREA SETTINGS” MODE ...................... 72
“CLEAR MEMORY” MODE ................................. 72
“EDIT ADDRESS BOOK” MODE ........................ 73
“GPS INFORMATION” MODE ............................. 73
“QUICK STOP CUSTOMER SETTING” MODE ... 73
“SET AVERAGE SPEED” MODE ........................ 73
“TRACKING” MODE ............................................ 74
GUIDANCE VOLUME ......................................... 74
DISPLAY WITH PUSHED “TRIP” BUTTON ........ 74
TRIP 1 OR TRIP 2 ............................................... 75
FUEL ECONOMY ................................................ 75
MAINTENANCE .................................................. 75
ENGINE OIL OR TIRE ROTATION ..................... 75
TIRE PRESSURE ................................................ 76
WARNING INDICATIONS ................................... 76
CAN Communication System Description .............. 76
Component Parts Location ..................................... 77
Schematic ............................................................... 78
Wiring Diagram — NAVI — ..................................... 79
Schematic ............................................................... 86
Wiring Diagram — COMM — ................................. 87
Terminals and Reference Value for NAVI Control
unit .......................................................................... 90
Terminals and Reference Value for Display Control
unit .......................................................................... 92
Terminals and Reference Value for Display unit ..... 96
Terminals and Reference Value for AV Switch ....... 98
Terminals and Reference Value for BCM ................ 99
On Board Self-Diagnosis Function .......................101
DESCRIPTION ..................................................101
DIAGNOSIS ITEM .............................................101
Self-Diagnosis Mode (DCU) .................................101
OPERATION PROCEDURE ..............................101
SELF–DIAGNOSIS RESULT .............................103
Self-Diagnosis Mode (NAVI) .................................104
OPERATION PROCEDURE ..............................104
SELF–DIAGNOSIS RESULT .............................105
Confirmation/Adjustment Mode ............................107
OPERATION PROCEDURE ..............................107
DISPLAY DIAGNOSIS .......................................108
VEHICLE SIGNALS ...........................................108
NAVIGATION .....................................................109
DISPLAY DIAGNOSIS .......................................109
VEHICLE SIGNALS ...........................................110
HISTORY OF ERRORS ....................................110
DIAGNOSIS BY HISTORY OF ERRORS ..........110
NAVIGATION .....................................................112
CAN DIAG SUPPORT MONITOR ........................114
OPERATION PROCEDURE ..............................114
AV Switch Self-Diagnosis Function .......................115
Power Supply and Ground Circuit Check for NAVI
Control Unit ...........................................................116
Power Supply and Ground Circuit Check for Display Control Unit ...........................................................117
Power Supply and Ground Circuit Check for Display
Unit ........................................................................118
Power Supply and Ground Circuit Check for AV
Switch ................................................................... 120
Vehicle Speed Signal Check for NAVI Control Unit . 121
Vehicle Speed Signal Check for Display Control Unit . 122
Illumination Signal Check for NAVI Control Unit ... 123
Illumination Signal Check for Display Control Unit . 123
Ignition Signal Check for NAVI Control Unit .......... 123
Ignition Signal Check for Display Control Unit ...... 124
Reverse Signal Check for NAVI Control Unit ........ 124
Reverse Signal Check for Display Control Unit .... 124
AV Communication Line Check (Between Display
Control Unit and NAVI Control Unit) ...................... 125
Audio Communication Line Check (Between Dis-
play Control Unit and Audio Unit) .......................... 126
Display Communication Line Check (Between Dis-
play Control Unit and Display Unit) ....................... 128
AV Communication Line Check (Between Display
Control Unit and AV Switch) .................................. 130
CAN Communication Line Check ......................... 131
If NAVI Control Unit Detects That DVD-ROM Map
is Not Inserted ....................................................... 131
If NAVI Control Unit Detects That Inserted DVD-
ROM Map is Malfunctioning or If It is Impossible to
Load Data from DVD-ROM Map ........................... 131
If Connection Between NAVI Control Unit and GPS
Antenna is Malfunctioning ..................................... 132
Operating Screen for Audio and A/C is Not Dis-
played When Showing NAVI Screen ..................... 132
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Bluish) ............................................ 134
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Reddish) ......................................... 135
Color of RGB Image is Not Proper (Only NAVI
Screen Looks Yellowish) ....................................... 136
Color of RGB Image is Not Proper (All Screen Looks
Bluish) ................................................................... 137
Color of RGB Image is Not Proper (All Screen Looks
Reddish) ................................................................ 138
Color of RGB Image is Not Proper (All Screen Looks
Yellowish) .............................................................. 139
NAVI Screen is Rolling .......................................... 140
Guide Sound is Not Heard .................................... 142
Screen is Not Shown ............................................ 143
A/C Screen is Not Shown (NAVI Screen is Shown) . 143
FUEL ECONOMY Screen is Not Shown ............... 143
Average Fuel Economy Displayed is Not Shown (“
*** ” is Shown) ....................................................... 143
Distance to Empty Displayed is Not Shown (“ *** ”
is Shown) .............................................................. 144
Driving Distance or Average Speed Displayed is Not
Shown (“ *** ” is Shown) ....................................... 144
WARNING DOOR OPEN Screen is Not Shown ... 144
Unable to Operate All of AV Switches (Unable to
Start Self-Diagnosis) ............................................. 145
Audio Does Not Work ........................................... 145
Navigation System Does Not Activate .................. 145

AUDIO
AV-29
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
NOTE:
1. The following noise results from variations in field strength, such as fading noise and multi-path noise, or
external noise from trains and other sources. It is not a malfunction.

Fading noise: This noise occurs because of variations in the field strength in a narrow range due to moun-
tains or buildings blocking the signal.

Multi-path noise: This noise results from the waves sent directly from the broadcast station arriving at the
antenna at a different time from the waves which reflect off mountains or buildings.
FOR CD ONLY
Noise InspectionEKS00BIH
The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and opera-
tion of each piece of electrical equipment, and determine the cause.
NOTE:
The source of the noise can be found easily by listening to the noise while removing the fuses of electrical
components, one by one.
TYPE OF NOISE AND POSSIBLE CAUSE
Symptom Possible cause
CD cannot be inserted.

CD

Audio unit CD cannot be ejected.
The CD cannot be played.
The sound skips, stops suddenly, or is distorted.
Occurrence condition Possible cause
Occurs only when engine is ON.A continuous growling noise occurs. The speed of
the noise varies with changes in the engine speed.

Ignition components
A whistling noise occurs while the engine speed is
high. A booming noise occurs while the engine is
running and the lighting switch is ON.

Generator
The occurrence of the noise is linked with the operation of the fuel pump.

Fuel pump condenser
Noise only occurs when various
electrical components are oper-
ating.A cracking or snapping sound occurs with the
operation of various switches.

Relay malfunction, audio unit malfunction
The noise occurs when various motors are operat-
ing.

Motor case ground

Motor
The noise occurs constantly, not just under certain conditions.

Rear defogger coil malfunction

Open circuit in printed heater

Poor ground of antenna amplifier or
antenna feeder line
A cracking or snapping sound occurs while the vehicle is being driven, especially
when it is vibrating excessively.

Ground wire of body parts

Ground due to improper part installation

Wiring connections or a short circuit

NAVIGATION SYSTEM
AV-101
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
On Board Self-Diagnosis FunctionEKS00BJP
DESCRIPTION

Diagnosis function consists of the self-diagnosis mode performed automatically and the CONFIRMATION/
ADJUSTMENT mode operated manually.

Self-diagnosis mode checks for connections between the units constituting this system, analyzes each
individual unit at the same time, and displays the results on the LCD screen.

CONFIRMATION/ADJUSTMENT mode is used to perform trouble diagnosis that require operation and
judgment by an operator (trouble that cannot be automatically judged by the system), to check/change the
set value, and to display the History of Errors of the navigation system.
DIAGNOSIS ITEM
NOTE:
Make the status that is set by D/N function be shown.
Self-Diagnosis Mode (DCU)EKS00BJQ
OPERATION PROCEDURE
1. Start the engine.
2. Turn the audio system off.
Mode Description
Self-diagnosis (DCU) Display control unit diagnosis.
Self-diagnosis (NAVI)

NAVI Control unit diagnosis (DVD-ROM drive) will not be diagnosed
when no map DVD-ROM is in it.

Analyzes connection between the NAVI control unit and the GPS
antenna and operation of each unit.
CONFIRMATION/
ADJUSTMENTDisplay diagnosisIn display control unit mode, color tone and shading of the screen can be
checked by the display of a color bar and a gray scale.
Vehicle signalsIn display control unit mode, analyzes the following vehicle signals: Vehi-
cle speed signal, light signal
NOTE , ignition switch signal, and reverse sig-
nal.
Auto Climate Control A/C self-diagnosis of A/C system.
NavigationDisplay diagnosisIn NAVI C/U mode, color tone and shading of the screen can be checked
by the display of a color bar and a gray scale.
Vehicle signalsIn NAVI C/U mode, analyzes the following vehicle signals: Vehicle speed
signal, light signal, ignition switch signal, and reverse signal.
History of ErrorsDiagnosis results previously stored in the memory (before turning ignition
switch ON) are displayed in this mode. Time and location when/where the
errors occurred are also displayed.
Naviga-
tionDisplay Lon-
gitude & Lat-
itudeDisplay the map. Use the joystick to adjust position. Longitude and latitude
will be displayed.
Speed Cali-
brationUnder ordinary conditions, the navigation system distance measuring
function will automatically compensate for minute decreases in wheel and
tire diameter caused by tire wear or low-pressure. Speed calibration imme-
diately restores system accuracy in cases such as when distance calibra-
tion is needed because of the use of tire chains in inclement weather.
Angle
adjustmentCorrects difference between actual turning angle of a vehicle and turning
angle of the car mark on the display.
Initialize
LocationThis mode is for initializing the current location. Use when the vehicle is
transported a long distance on a trailer, etc.
CAN DIAG SUPPORT MONITOR Display status of CAN communication.

NAVIGATION SYSTEM
AV-107
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: October 20052005 QX56
Confirmation/Adjustment ModeEKS00BJS
OPERATION PROCEDURE
1. Start the engine.
2. Turn the audio system off.
3. While pressing the “PAUSE/MUTE” button, turn the volume con-
trol dial clockwise or counterclockwise for 30 clicks or more.
(When the self-diagnosis mode is started, a short beep will be
heard.)

Shifting from current screen to previous screen is performed
by pressing “PREV” button.
4. The initial self-diagnosis screen will be shown, and items “Self-
Diagnosis (DCU)”, “Self-Diagnosis (NAVI)”, “Confirmation/
Adjustment” and “CAN DIAG SUPPORT MONITOR” will
become selective.
5. When “Confirmation/Adjustment” is selected on the initial self-
diagnosis screen, the operation will enter the CONFIRMATION/
ADJUSTMENT mode. In this mode, check and adjustment of
each item will become possible.
6. The initial trouble diagnosis screen will be shown, and items
“Display Diagnosis”, “Vehicle Signals”, “Auto Climate Control”
and “Navigation” will become selective.
7. Select each switch on “CONFIRMATION/ADJUSTMENT”
screen to display the relevant diagnosis screen.
WKIA1504E
SKIA4207E
SKIA4220E

SQUEAK AND RATTLE TROUBLE DIAGNOSES
BL-7
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: October 20052005 QX56
DUPLICATE THE NOISE AND TEST DRIVE
If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or location of the noise. This information can be used to
duplicate the same conditions when you confirm the repair.
If the noise can be duplicated easily during the test drive, to help identify the source of the noise, try to dupli-
cate the noise with the vehicle stopped by doing one or all of the following:
1) Close a door.
2) Tap or push/pull around the area where the noise appears to be coming from.
3) Rev the engine.
4) Use a floor jack to recreate vehicle “twist”.
5) At idle, apply engine load (electrical load, half-clutch on M/T model, drive position on A/T model).
6) Raise the vehicle on a hoist and hit a tire with a rubber hammer.

Drive the vehicle and attempt to duplicate the conditions the customer states exist when the noise occurs.

If it is difficult to duplicate the noise, drive the vehicle slowly on an undulating or rough road to stress the
vehicle body.
CHECK RELATED SERVICE BULLETINS
After verifying the customer concern or symptom, check ASIST for Technical Service Bulletins (TSBs) related
to that concern or symptom.
If a TSB relates to the symptom, follow the procedure to repair the noise.
LOCATE THE NOISE AND IDENTIFY THE ROOT CAUSE
1. Narrow down the noise to a general area.To help pinpoint the source of the noise, use a listening tool
(Chassis Ear: J-39570, Engine Ear: J-39565 and mechanic's stethoscope).
2. Narrow down the noise to a more specific area and identify the cause of the noise by:

removing the components in the area that you suspect the noise is coming from.
Do not use too much force when removing clips and fasteners, otherwise clips and fasteners can be bro-
ken or lost during the repair, resulting in the creation of new noise.

tapping or pushing/pulling the component that you suspect is causing the noise.
Do not tap or push/pull the component with excessive force, otherwise the noise will be eliminated only
temporarily.

feeling for a vibration with your hand by touching the component(s) that you suspect is (are) causing the
noise.

placing a piece of paper between components that you suspect are causing the noise.

looking for loose components and contact marks.
Refer to BL-8, "
Generic Squeak and Rattle Troubleshooting" .
REPAIR THE CAUSE

If the cause is a loose component, tighten the component securely.

If the cause is insufficient clearance between components:
–separate components by repositioning or loosening and retightening the component, if possible.
–insulate components with a suitable insulator such as urethane pads, foam blocks, felt cloth tape or ure-
thane tape. A NISSAN Squeak and Rattle Kit (J-43980) is available through your authorized NISSAN
Parts Department.
CAUTION:
Do not use excessive force as many components are constructed of plastic and may be damaged.
Always check with the Parts Department for the latest parts information.
The following materials are contained in the NISSAN Squeak and Rattle Kit (J-43980). Each item can be
ordered separately as needed.
URETHANE PADS [1.5 mm (0.059 in) thick]
Insulates connectors, harness, etc.
76268-9E005: 100×135 mm (3.94×5.31 in)/76884-71L01: 60×85 mm (2.36×3.35 in)/76884-71L02: 15×25
mm (0.59×0.98 in)
INSULATOR (Foam blocks)
Insulates components from contact. Can be used to fill space behind a panel.
73982-9E000: 45 mm (1.77 in) thick, 50×50 mm (1.97×1.97 in)/73982-50Y00: 10 mm (0.39 in) thick,
50×50 mm (1.97×1.97 in)
INSULATOR (Light foam block)

HOOD
BL-15
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: October 20052005 QX56
INSTALLATION
1. Pull the hood lock cable through the dash lower hole into the engine room.
Be careful not to bend the cable too much, keeping the radius
100mm (3.94 in) or more.
2. Make sure the cable is not offset from the positioning grommet,
and push the grommet into the dash lower hole securely.
3. Apply sealant around the grommet at * mark.
4. Install the primary and secondary cables securely to the hood
lock.
5. Install the hood lock and the secondary hood lock release
assemblies.
6. Check the hood lock adjustment and hood opener operation.
Refer to BL-12, "
Fitting Adjustment" .
Hood Lock Control InspectionEIS008PD
CAUTION:
If the hood lock cable is bent or deformed, replace it.
1. Remove the front grille. Refer to EI-17, "
FRONT GRILLE" .
2. Make sure the secondary latch is properly engaged with the sec-
ondary striker with hood's own weight by dropping it from
approx. 200 mm (7.87 in) height.
3. While operating the hood opener, carefully make sure the front
end of the hood is raised by approx. 20 mm (0.79 in). Also make
sure the hood opener returns to the original position.
4. Check the hood lock lubrication condition. If necessary, apply
“body grease” to the points shown in the figure.
5. Install the front grille. Refer to EI-17, "
FRONT GRILLE" .
PIIA0173E
PIIA0174E
PIIA1086E
PIIA0176E

AUTOMATIC BACK DOOR SYSTEM
BL-113
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: October 20052005 QX56
Trouble Diagnosis ProcedureEIS008R9
1. Check the trouble symptom and customer's requests.
2. Understand outline of system. Refer to BL-45, "
System Description" .
3. Confirm system operation.
4. Perform self-diagnosis procedures. Refer to BL-113, "
Self-Diagnosis Procedures" .
5. Refer to diagnosis chart by symptom, repair or replace any malfunctioning parts. Refer to BL-114, "
Diag-
nosis Chart" .
6. Inspection End.
Self-Diagnosis ProceduresEIS008RA
INPUT SIGNAL CHECK MODE
Input signal check mode allows testing of switch input signal to the back door control unit.
To activate input signal check mode on the automatic back door, perform the following steps:
1. Turn ignition switch OFF.
2. Turn back door close switch to CANCEL (system cancelled).
3. Place A/T selector lever in P position.
4. Using the inside emergency release lever, open the back door.
5. Have an assistant press and hold the back door handle switch.
6. While the assistant continues to hold the back door handle switch, turn ignition switch ON (DO NOT start
engine).
7. After approximately 5 seconds, the back door warning chime will sound for 0.5 seconds.
8. Release the back door handle switch.
9. Within 8 seconds of the back door warning chime sounding, press and hold the power liftgate switch.
10. After approximately 5 seconds, the back door warning chime will sound for 1 second.
11. Release the power liftgate switch.
12. The input signal check mode is now initialized.
The input signal check mode can test the following inputs. The back door warning chime will sound for approx-
imately 0.5 seconds each time a switch signal input occurs. Use this test when one of these inputs is not
responding during normal automatic back door operation.
*Back door warning chime should sound as soon as vehicle moves.
Turn ignition switch OFF to end input signal check mode.
OPERATING CHECK MODE
Operating check mode allows self-diagnosis of the automatic back door system.
To activate operating check mode on the automatic back door, perform the following steps:
1. Turn ignition switch OFF.
2. Turn back door close switch to CANCEL (system cancelled).
3. Place A/T selector lever in P position.
Switch signal Operation Refer to
Power liftgate switch OFF → ONBL-116
Back door close switch (CLOSE) OFF → ONBL-118
Back door close switch (CANCEL) OFF → ONBL-119
Back door handle switch OFF → ONBL-125
Glass switch OFF → ONBL-117
A/T device (park switch) P position → other than P positionAT-6 0
Vehicle speed* Vehicle speed —
Remote keyless entry signal Keyfob switch OFF → ONBL-44
Door lock/unlock signal LOCK → UNLOCKBL-16
Pinch strip LH signal OFF → ONBL-121
Pinch strip RH signal OFF → ONBL-121