2005 INFINITI FX35 timing belt

QUICK REFERENCE CHART M35/M45
QUICK REFERENCE CHART M35/M45PFP:00000
ENGINE TUNE-UP DATA (VQ35DE)ELS0003W
Engine modelVQ35DE
Firing order1-2-3-4-5-6
Idle speed
A/T (In “P” or “N” position)rpm
650 ± 50
Ignition timing (BTDC at idle speed)
A/T (In “P” or “N” position)15° ± 5°
CO% at idle 0.7 - 9.9 % and engine runs smoothly
Drive BeltDeflection adjustment Unit: mm (in) Tension adjustment Unit: N (kg, lb)
Used belt
New beltUsed belt
New belt
Limit After adjustment Limit After adjustment
Alternator and power
steering oil pump belt7 (0.28)4 - 5
(0.16 - 0.20)3.5 - 4.5
(0.138 - 0.177)294 (30, 66)730 - 818
(74.5 - 83.5,
164 - 184)838 - 926
(85.5 - 94.5,
188 - 208)
A/C compresor belt 12 (0.47)9 - 10
(0.35 - 0.39)8 - 9
(0.31 - 0.35)196 (20, 44)348 - 436
(35.5 - 44.5,
78 - 98)470 - 559
( 4 8 - 5 7 ,
106 - 126)
Applied pushing force 98N (10kg, 22lb) —
Radiator cap relief pressure
kPa (kg/cm
2 , psi)
Standard 78 - 98 (0.8 - 1.0, 11 - 14)
Limit 59 (0.6, 9)
Cooling system leakage testing pres-
surekPa (kg/cm
2 , psi)157 (1.6, 23)
Compression pressure
kPa (kg/cm
2 , psi)/rpm
Standard 1,275 (13.0, 185) /300
Minimum 981 (10.0, 142) /300
Spark plug Standard type PLFR5A-11
Hot type PLFR4A-11
Cold type PLFR6A-11
2005

QUICK REFERENCE CHART M35/M45
ENGINE TUNE-UP DATA (VK45DE)
FRONT WHEEL ALIGNMENT (Unladen* )
ELS0003X
* : Fuel, engine coolant and engine oil full. Spare tire, jack, hand tools and mats in designated positions.Engine modelVK45DE
Firing order1-8-7-3-6-5-4-2
Idle speed
A/T (In “P” or “N” position) rpm650 ± 50
Ignition timing
(BTDC at idle speed)12° ± 5°
CO% at idle 0.7 - 9.9 % and engine runs smoothly
Tensions of drive belts Auto adjustment by auto tensioner
Radiater cap relief pressure
kPa (kg/cm
2 , psi)
78 - 98 (0.8-1.0 , 11-14) Standard
Limit 59 (0.6, 9)
Cooling system leakage testing pressure
157 (1.6, 23)
kPa (kg/cm
2 , psi)
Compression pressure
kPa (kg/cm
2 , psi)/rpm
1,320 (13.5, 191) /300 Standard
Minimum 1,130 (11.5, 164) /300
Spark plug Standard type PLFR5A-11
Hot type PLFR4A-11
Cold type PLFR6A-11
Camber Degree minute (Decimal degree) Minimum – 1° 29′ (– 1.48°)
Nominal – 0° 44′ (– 0.73°)
Maximum 0° 01′ (0.02°)
Left and right difference 45′ (0.75°) or less
Caster Degree minute (Decimal degree) Minimum 3° 02′ (3.03°)
Nominal 3° 47′ (3.78°)
Maximum 4° 32′ (4.53°)
Left and right difference 45′ (0.75°) or less
Kingpin inclination Degree minute (Decimal degree) Minimum 12° 20′ (12.33°)
Nominal 13° 05′ (13.08°)
Maximum 13° 50′ (13.83°)
Total toe-in Distance (A – B) Minimum 0.6 mm (0.024 in)
Nominal 1.6 mm (0.063 in)
Maximum 2.6 mm (0.102 in)
Angle (left plus right)
Degree minute (Degree)Minimum –
Nominal 6′ (0.1°)
Maximum –
Wheel turning angle (Full turn) Inside Minimum 32° 00 (32.0°)
Degree minute (Decimal degree) Nominal 35° 00 (35.0°)
Maximum 36° 00 (36.0°)
Outside
Nominal 30° 00 (30.0°)
Degree minute (Decimal degree)
2005

ATC-162
SERVICE DATA AND SPECIFICATIONS (SDS)
Revision: 2005 July 2005 FX
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
CompressorAJS00167
LubricantAJS00168
RefrigerantAJS00169
Engine Idling SpeedAJS0016A
Refer to EC-83, "Idle Speed and Ignition Timing Check" (VQ35DE) or EC-774, "Idle Speed and Ignition Tim-
ing Check" (VK45DE).
Belt TensionAJS0016B
Refer to EM-15, "DRIVE BELTS" (VQ35DE) or EM-173, "DRIVE BELTS" (VK45DE).
Model Calsonic Kansei make CWV-618
Ty p e V-6 variable displacement
Displacement
cm
3 (cu in)/rev Max. 184 (11.228)
Min. 14.5 (0.885)
Cylinder bore × stroke
mm (in) 37 (1.46)
× [2.3 - 28.6 (0.091 - 1.126)]
Direction of rotation Clockwise (viewed from drive end)
Drive belt Poly V
ModelCalsonic Kansei make CWV-618
Name Nissan A/C System Oil Type S (DH-PS)
Part number KLH00-PAGS0
Capacity
m (US fl oz, lmp fl oz) Total in system 180 (6.0, 6.3)
Compressor (Service part) charg-
ing amount 180 (6.0, 6.3)
Ty p e
HFC-134a (R-134a)
Capacity
kg (lb) 0.55 (1.21)

CO-22
[VQ35DE]
WATER PUMP
Revision: 2005 July 2005 FX
WATE R P U M PPFP:21020
ComponentsABS00E80
Removal and InstallationABS009RE
CAUTION:

When removing water pump assembly, be careful not to get engine coolant on drive belts.

Water pump cannot be disassembled and should be replaced as a unit.

After installing water pump, connect hose and clamp securely, then check for leaks using the radi-
ator cap tester (commercial service tool) and the radiator cap tester adapter [SST: EG17650301
(J33984-A)].
REMOVAL
1. Remove front engine undercover with power tool.
2. Remove drive belts. Refer to EM-15, "
DRIVE BELTS" .
3. Drain engine coolant from radiator. Refer to CO-11, "
Changing Engine Coolant" .
CAUTION:

Perform this step when the engine is cold.

Do not spill engine coolant on drive belts.
4. Remove air duct (inlet), power duct and air cleaner case assembly. Refer to EM-17, "
AIR CLEANER AND
AIR DUCT" .
5. Remove water drain plug (front) on water pump side of cylinder block to drain engine coolant from engine inside.
6. Remove chain tensioner cover and water pump cover from front timing chain case.

U s e t h e s e a l c u t t e r [ S S T: K V 1 0 1111 0 0 ( J 3 7 2 2 8 ) ] t o c u t l i q u i d g a s k e t f o r r e m o v a l .
1. Timing chain tensioner (primary) 2. Chain tensioner cover 3. Water pump cover
4. Water pump 5. O-rings 6. Water drain plug (front)
SBIA0482E
PBIC2662E

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D E
F
G H
I
J
K L
M
SECTION EC
A
EC
Revision: 2005 July 2005 FX
ENGINE CONTROL SYSTEM
VQ35DE
INDEX FOR DTC ...................................................... 15
DTC No. Index .................................................... ... 15
Alphabetical Index ............................................... ... 19
PRECAUTIONS ..................................................... ... 23
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ... 23
On Board Diagnostic (OBD) System of Engine and
A/T ....................................................................... ... 23
Precaution ........................................................... ... 23
PREPARATION ...................................................... ... 27
Special Service Tools .......................................... ... 27
Commercial Service Tools ................................... ... 29
ENGINE CONTROL SYSTEM ............................... ... 30
System Diagram .................................................. ... 30
Multiport Fuel Injection (MFI) System ................. ... 31
Electronic Ignition (EI) System ............................ ... 33
Fuel Cut Control (at No Load and High Engine
Speed) ................................................................. ... 34
AIR CONDITIONING CUT CONTROL .................. ... 35
Input/Output Signal Chart .................................... ... 35
System Description ............................................. ... 35
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ... 36
System Description ............................................. ... 36
Component Description ....................................... ... 37
CAN COMMUNICATION ....................................... ... 38
System Description ............................................. ... 38
EVAPORATIVE EMISSION SYSTEM .................... ... 39
Description .......................................................... ... 39
Component Inspection ........................................ ... 42
Removal and Installation ..................................... ... 43
How to Detect Fuel Vapor Leakage .................... ... 43
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ................................................................... ... 46
System Description ............................................. ... 46
Diagnostic Procedure .......................................... ... 47
Component Inspection ........................................ ... 49 POSITIVE CRANKCASE VENTILATION ..............
... 51
Description ........................................................... ... 51
Component Inspection ......................................... ... 51
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ..................................................................... ... 53
Description ........................................................... ... 53
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......... ... 54
Introduction .......................................................... ... 54
Two Trip Detection Logic ..................................... ... 54
Emission-Related Diagnostic Information ............ ... 55
Malfunction Indicator Lamp (MIL) ........................ ... 69
OBD System Operation Chart ............................. ... 72
BASIC SERVICE PROCEDURE ............................ ... 78
Basic Inspection .................................................. ... 78
Idle Speed and Ignition Timing Check ................. ... 83
Idle Mixture Ratio Adjustment .............................. ... 85
VIN Registration .................................................. ... 96
Accelerator Pedal Released Position Learning ... ... 96
Throttle Valve Closed Position Learning .............. ... 96
Idle Air Volume Learning ..................................... ... 97
Fuel Pressure Check ........................................... ... 99
TROUBLE DIAGNOSIS ......................................... .101
Trouble Diagnosis Introduction ............................ .101
DTC Inspection Priority Chart .............................. .107
Fail-Safe Chart .................................................... .109
Symptom Matrix Chart ......................................... .110
Engine Control Component Parts Location ......... .114
Vacuum Hose Drawing ........................................ .120
Circuit Diagram .................................................... .121
ECM Harness Connector Terminal Layout .......... .123
ECM Terminals and Reference Value .................. .123
CONSULT-II Function (ENGINE) ......................... .132
Generic Scan Tool (GST) Function ...................... .144
CONSULT-II Reference Value in Data Monitor .... .147
Major Sensor Reference Graph in Data Monitor
Mode .................................................................... .151
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .153
Description ........................................................... .153
Testing Condition ................................................. .153

EC-8Revision: 2005 July 2005 FX
VK45DE
INDEX FOR DTC .....................................................707
DTC No. Index ..................................................... .707
Alphabetical Index ............................................... .711
PRECAUTIONS ...................................................... .715
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .............................................................. .715
On Board Diagnostic (OBD) System of Engine and
A/T ....................................................................... .715
Precaution ........................................................... .715
PREPARATION ...................................................... .719
Special Service Tools .......................................... .719
Commercial Service Tools ................................... .720
ENGINE CONTROL SYSTEM ............................... .721
System Diagram .................................................. .721
Multiport Fuel Injection (MFI) System .................. .722
Electronic Ignition (EI) System ............................ .724
Fuel Cut Control (at No Load and High Engine
Speed) ................................................................. .725
AIR CONDITIONING CUT CONTROL ................... .726
Input/Output Signal Chart .................................... .726
System Description .............................................. .726
AUTOMATIC SPEED CONTROL DEVICE (ASCD) .727
System Description .............................................. .727
Component Description ....................................... .728
CAN COMMUNICATION ........................................ .729
System Description .............................................. .729
EVAPORATIVE EMISSION SYSTEM .................... .730
Description ........................................................... .730
Component Inspection ......................................... .733
Removal and Installation ..................................... .734
How to Detect Fuel Vapor Leakage ..................... .734
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ................................................................... .737
System Description .............................................. .737
Diagnostic Procedure .......................................... .738
Component Inspection ......................................... .740
POSITIVE CRANKCASE VENTILATION .............. .742
Description ........................................................... .742
Component Inspection ......................................... .742
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ..................................................................... .744
Description ........................................................... .744
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......... .745
Introduction .......................................................... .745
Two Trip Detection Logic ..................................... .745
Emission-Related Diagnostic Information ............ .746
Malfunction Indicator Lamp (MIL) ........................ .760
OBD System Operation Chart ............................. .764
BASIC SERVICE PROCEDURE ............................ .769
Basic Inspection .................................................. .769
Idle Speed and Ignition Timing Check ................. .774
Idle Mixture Ratio Adjustment .............................. .775
VIN Registration .................................................. .786
Accelerator Pedal Released Position Learning ... .786
Throttle Valve Closed Position Learning .............. .786 Idle Air Volume Learning ......................................
.787
Fuel Pressure Check ........................................... .789
TROUBLE DIAGNOSIS ......................................... .791
Trouble Diagnosis Introduction ............................ .791
DTC Inspection Priority Chart .............................. .797
Fail-Safe Chart ..................................................... .799
Symptom Matrix Chart ......................................... .800
Engine Control Component Parts Location .......... .804
Vacuum Hose Drawing ........................................ .810
Circuit Diagram .................................................... .811
ECM Harness Connector Terminal Layout ........... .813
ECM Terminals and Reference Value .................. .813
CONSULT-II Function (ENGINE) ......................... .822
Generic Scan Tool (GST) Function ...................... .835
CONSULT-II Reference Value in Data Monitor .... .838
Major Sensor Reference Graph in Data Monitor
Mode .................................................................... .842
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .844
Description ........................................................... .844
Testing Condition ................................................. .844
Inspection Procedure ........................................... .844
Diagnostic Procedure ........................................... .845
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT ...................................................................... .854
Description ........................................................... .854
Diagnostic Procedure ........................................... .854
POWER SUPPLY AND GROUND CIRCUIT .......... .855
Wiring Diagram .................................................... .855
Diagnostic Procedure ........................................... .856
Ground Inspection ................................................ .861
DTC U1000, U1001 CAN COMMUNICATION LINE .862
Description ........................................................... .862
On Board Diagnosis Logic ................................... .862
DTC Confirmation Procedure ............................... .862
Wiring Diagram .................................................... .863
Diagnostic Procedure ........................................... .864
DTC P0011, P0021 IVT CONTROL ........................ .865
Description ........................................................... .865
CONSULT-II Reference Value in Data Monitor Mode .866
On Board Diagnosis Logic ................................... .866
DTC Confirmation Procedure ............................... .867
Wiring Diagram .................................................... .868
Diagnostic Procedure ........................................... .871
Component Inspection ......................................... .875
Removal and Installation ...................................... .876
DTC P0031, P0032, P0051, P0052 HO2S1 HEATER .877
Description ........................................................... .877
CONSULT-II Reference Value in Data Monitor Mode .877
On Board Diagnosis Logic ................................... .877
DTC Confirmation Procedure ............................... .878
Wiring Diagram .................................................... .879
Diagnostic Procedure ........................................... .882
Component Inspection ......................................... .884
Removal and Installation ...................................... .884
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .885
Description ........................................................... .885
CONSULT-II Reference Value in Data Monitor Mode

TROUBLE DIAGNOSIS - SPECIFICATION VALUE EC-159
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
Revision: 2005 July 2005 FX
15. DISCONNECT AND RECONNECT ECM HARNESS CONNECTOR
1. Stop the engine.
2. Disconnect ECM harness connector. Check pin terminal and connector for damage, and then reconnect it.
>> GO TO 16.
16. CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”
1. Start engine.
2. Select “A/F ALPHA-B1”, “A/F ALPHA-B2” in “DATA MONITOR (SPEC)” mode, and make sure that the each indication is within the SP value.
OK or NG
OK >> INSPECTION END
NG >> Detect malfunctioning part according to EC-110, "
Symptom Matrix Chart" .
17. CHECK “B/FUEL SCHDL”
Select “B/FUEL SCHDL” in “DATA MONITOR (SPEC)” mode, and
make sure that the indication is within the SP value.
OK or NG
OK >> INSPECTION END
NG (More than the SP value)>>GO TO 18.
NG (Less than the SP value)>>GO TO 25.
18. DETECT MALFUNCTIONING PART
1. Check for the cause of large engine friction. Refer to the following.
–Engine oil level is too high
–Engine oil viscosity
–Belt tension of power steering, alternator, A/C compressor, etc. is excessive
–Noise from engine
–Noise from transmission, etc.
2. Check for the cause of insufficient combustion. Refer to the following.
–Valve clearance malfunction
–Intake valve timing control function malfunction
–Camshaft sprocket installation malfunction, etc.
>> Repair or replace malfunctioning part, and then GO TO 30.
19. CHECK INTAKE SYSTEM
Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.

Crushed air ducts

Malfunctioning seal of air cleaner element

Uneven dirt of air cleaner element

Improper specification of intake air system
OK or NG
OK >> GO TO 21.
NG >> Repair or replace malfunctioning part, and then GO TO 20.
PBIB2332E

EC-850
[VK45DE]
TROUBLE DIAGNOSIS - SPECIFICATION VALUE
Revision: 2005 July 2005 FX
15. DISCONNECT AND RECONNECT ECM HARNESS CONNECTOR
1. Stop the engine.
2. Disconnect ECM harness connector. Check pin terminal and connector for damage, and then reconnect it.
>> GO TO 16.
16. CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”
1. Start engine.
2. Select “A/F ALPHA-B1”, “A/F ALPHA-B2” in “DATA MONITOR (SPEC)” mode, and make sure that the each indication is within the SP value.
OK or NG
OK >> INSPECTION END
NG >> Detect malfunctioning part according to EC-800, "
Symptom Matrix Chart" .
17. CHECK “B/FUEL SCHDL”
Select “B/FUEL SCHDL” in “DATA MONITOR (SPEC)” mode, and
make sure that the indication is within the SP value.
OK or NG
OK >> INSPECTION END
NG (More than the SP value)>>GO TO 18.
NG (Less than the SP value)>>GO TO 25.
18. DETECT MALFUNCTIONING PART
1. Check for the cause of large engine friction. Refer to the following.
–Engine oil level is too high
–Engine oil viscosity
–Belt tension of power steering, alternator, A/C compressor, etc. is excessive
–Noise from engine
–Noise from transmission, etc.
2. Check for the cause of insufficient combustion. Refer to the following.
–Valve clearance malfunction
–Intake valve timing control function malfunction
–Camshaft sprocket installation malfunction, etc.
>> Repair or replace malfunctioning part, and then GO TO 30.
19. CHECK INTAKE SYSTEM
Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.

Crushed air ducts

Malfunctioning seal of air cleaner element

Uneven dirt of air cleaner element

Improper specification of intake air system
OK or NG
OK >> GO TO 21.
NG >> Repair or replace malfunctioning part, and then GO TO 20.
PBIB2332E