2005 INFINITI FX35 temperature sensor location

TROUBLE DIAGNOSIS — GENERAL DESCRIPTION ACS-31
[ICC]
C
D E
F
G H
I
J
L
M A
B
ACS
Revision: 2005 July 2005 FX
6. Touch any of “WORK SUPPORT”, “SELF-DIAG RESULTS”,
“DATA MONITOR”, “CAN DIAG SUPPORT MNTR”, “ACTIVE
TEST” and “ECU PART NUMBER” on selection screen.
WORK SUPPORT
Work Item
Cause of Auto-Cancel
1. Touch “WORK SUPPORT” on the “SELECT DIAG MODE” screen. Refer to ACS-30, "
CONSULT-II BASIC OPERATION" .
2. Touch “CAUSE OF AUTO-CANCEL” on the “SELECT WORK ITEM” screen.
3. Cause of automatic cancellation screen will be shown. CAUTION:
Last five cancel (system cancel) causes are displayed.
Display Item List
Laser Beam Adjust
For details, refer to ACS-12, "LASER BEAM AIMING ADJUSTMENT" .
PKIA8867E
Operation Function
CAUSE OF AUTO-CANCEL Indicates causes of automatic cancellation of the ICC system.
LASER BEAM ADJUST Outputs laser beam, calculates dislocation of the beam, and indicates adjustment direction.
SKIA6191E
Cause of cancellation Description
OPERATING WIPER Windshield wipers were operated at HI or LO speed operation.
OPERATING ABS ABS function was operated.
OPERATING TCS TCS function was operated.
OPERATING VDC VDC function was operated.
OPE SW VOLT CIRC Outside the standard control switch input voltage was detected.
ECM CIRCUIT ECM did not permit ICC operation.
LASER SUN BEAM Intense light such as sunlight entered ICC sensor light sensing part.
LASER TEMP Temperature around ICC sensor became low.
OP SW DOUBLE TOUCH ICC steering switches were pressed at the same time.
WHL SPD ELEC NOISE Wheel speed sensor signal caught electromagnetic noise.
VDC/TCS OFF SW VDC OFF switch was pressed.
WHEEL SPD UNMATCH Wheel speed became different from AT vehicle speed.
TIRE SLIP Wheel slipped.
PKB SW ON Parking brake is applied.
IGN LOW VOLT Power supply voltage became low.
SNOW MODE SW Snow mode switch was pressed.
NO RECORD —

AT-4Revision: 2005 July 2005 FX
In “N” Position, Vehicle Moves .............................
.196
Large Shock (“N” to “D” Position) ........................ .197
Vehicle Does Not Creep Backward in “R” Position .200
Vehicle Does Not Creep Forward in “D” Position . .203
Vehicle Cannot Be Started from D
1 ..................... .205
A/T Does Not Shift: D
1 → D2 ............................... .208
A/T Does Not Shift: D
2 → D3 ............................... .210
A/T Does Not Shift: D
3 → D4 ............................... .212
A/T Does Not Shift: D
4 → D5 ............................... .215
A/T Does Not Perform Lock-up ........................... .217
A/T Does Not Hold Lock-up Condition ................. .219
Lock-up Is Not Released ..................................... .221
Engine Speed Does Not Return to Idle ............... .221
Cannot Be Changed to Manual Mode ................. .223
A/T Does Not Shift: 5th Gear → 4th Gear ........... .223
A/T Does Not Shift: 4th Gear → 3rd Gear ........... .225
A/T Does Not Shift: 3rd Gear → 2nd Gear .......... .227
A/T Does Not Shift: 2nd Gear → 1st Gear ........... .229
Vehicle Does Not Decelerate by Engine Brake ... .231
SHIFT CONTROL SYSTEM ................................... .233
Control Device Removal and Installation ............. .233
Control Rod Removal and Installation ................. .234
Adjustment of A/T Position .................................. .235
Checking of A/T Position ..................................... .235
A/T SHIFT LOCK SYSTEM .................................... .236
Description ........................................................... .236
Shift Lock System Electrical Parts Location ........ .236
Wiring Diagram — AT — SHIFT .......................... .237
Diagnostic Procedure .......................................... .238
KEY INTERLOCK CABLE ..................................... .240
Components ........................................................ .240
Removal and Installation ..................................... .241
ON-VEHICLE SERVICE ......................................... .243
Control Valve with TCM and A/T Fluid Temperature
Sensor 2 .............................................................. .243
Parking Components (2WD Models Only) ........... .255
Rear Oil Seal ....................................................... .262
Revolution Sensor Components (2WD Models Only) ....................................................................
.263
AIR BREATHER HOSE .......................................... .268
Removal and Installation ...................................... .268
TRANSMISSION ASSEMBLY ................................ .270
Removal and Installation (2WD Models) .............. .270
Removal and Installation (AWD Models) ............. .273
OVERHAUL ............................................................ .278
Components ......................................................... .278
Oil Channel .......................................................... .286
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ......................... .288
DISASSEMBLY ...................................................... .290
Disassembly ......................................................... .290
REPAIR FOR COMPONENT PARTS ..................... .308
Oil Pump .............................................................. .308
Front Sun Gear, 3rd One-way Clutch ................... .311
Front Carrier, Input Clutch, Rear Internal Gear .... .313
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub ............................................. .318
High and Low Reverse Clutch ............................. .323
Direct Clutch ........................................................ .326
ASSEMBLY ............................................................ .328
Assembly (1) ........................................................ .328
Adjustment ........................................................... .341
Assembly (2) ........................................................ .344
SERVICE DATA AND SPECIFICATIONS (SDS) ... .351
General Specifications ......................................... .351
Vehicle Speed at Which Gear Shifting Occurs ..... .351
Vehicle Speed at Which Lock-up Occurs/Releases .352
Stall Speed ........................................................... .352
Line Pressure ....................................................... .352
A/T Fluid Temperature Sensor ............................. .352
Turbine Revolution Sensor ................................... .353
Vehicle Speed Sensor A/T (Revolution Sensor) .. .353
Reverse Brake ..................................................... .353
Total End Play ...................................................... .353

DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVE AT-125
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
DTC P0740 TORQUE CONVERTER CLUTCH SOLENOID VALVEPFP:31940
DescriptionACS002N0

The torque converter clutch solenoid valve is activated, with the gear in D5 , M4 and M5 by the TCM in
response to signals sent from the vehicle speed sensor and accelerator pedal position sensor (throttle
position sensor). Torque converter clutch piston operation will then be controlled.

Lock-up operation, however, is prohibited when A/T fluid temperature is too low.

When the accelerator pedal is depressed (less than 1.0/8) in lock-up condition, the engine speed should
not change abruptly. If there is a big jump in engine speed, there is no lock-up.
CONSULT-II Reference ValueACS002N1
On Board Diagnosis LogicACS002N2

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “P0740 TCC SOLENOID/CIRC” with CONSULT-II or 3rd judgement flicker with-
out CONSULT-II is detected under the following conditions.
–When TCM detects an improper voltage drop when it tries to operate the solenoid valve.
–When TCM detects as irregular by comparing target value with monitor value.
Possible CauseACS002N3

Torque converter clutch solenoid valve

Harness or connectors
(Solenoid circuit is open or shorted.)
DTC Confirmation ProcedureACS002N4
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch ON. (Do not start engine.)
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Touch “START”.
4. Start engine and maintain the following conditions for at least 5 consecutive seconds.
VHCL SPEED SE: 80 km/h (50 MPH) or more
ACCELE POSI: 0.5/8 - 1.0/8
SELECTOR LEVER: “D” position
Driving location: Driving the vehicle uphill (increased
engine load) will help maintain the driving conditions
required for this test.
5. If DTC is detected go to AT- 1 2 6 , "
Diagnostic Procedure" .
WITH GST
Follow the procedure “WITH CONSULT-II”.
Item name Condition Display value (Approx.)
TCC SOLENOID Slip lock-up is active 0.2 - 0.4 A
Lock-up is active 0.4 - 0.6 A
BCIA0031E

ON-VEHICLE SERVICE AT-249
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX

Assemble it so that manual valve cutout is engaged with
manual plate projection.
8. Install bolts A, B and C in control valve with TCM.
9. Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After that tighten them in order (1 → 2 → 3), and then tighten other
bolts.
10. Connect A/T fluid temperature sensor 2 connector.
11. Securely fasten terminal cord assembly and A/T fluid tempera- ture sensor 2 harness with terminal clips.
SCIA5142E
Bolt symbol Length mm (in) Number of bolts
A 42 (1.65) 5
B 55 (2.17) 6
C 40 (1.57) 1
SCIA5139E
: 7.9 N·m (0.81 kg-m, 70 in-lb)
SCIA5140E
SCIA5023E
SCIA5446E

ATC-2Revision: 2005 July 2005 FX
MODE SWITCH ................................................
... 35
FAN SWITCH ................................................... ... 35
DUAL SWITCH (WITH LEFT AND RIGHT VEN-
TILATION TEMPERATURE SEPARATELY
CONTROL SYSTEM) ....................................... ... 35
Fail-safe Function ................................................ ... 36
Discharge Air Flow .............................................. ... 37
System Description .............................................. ... 38
SWITCHES AND THEIR CONTROL FUNCTION ... 38
CAN Communication System Description ........... ... 39
TROUBLE DIAGNOSIS ......................................... ... 40
CONSULT-II Function (BCM) ............................... ... 40
CONSULT-II BASIC OPERATION .................... ... 40
DATA MONITOR ............................................... ... 41
How to Perform Trouble Diagnosis for Quick and
Accurate Repair ................................................... ... 42
WORK FLOW ................................................... ... 42
SYMPTOM TABLE ........................................... ... 42
Component Parts and Harness Connector Location ... 43
ENGINE COMPARTMENT ............................... ... 43
PASSENGER COMPARTMENT ....................... ... 44
Schematic ............................................................ ... 45
Wiring Diagram —A/C— ...................................... ... 46
Auto Amp. Terminals and Reference Value ......... ... 51
PIN CONNECTOR TERMINAL LAYOUT ......... ... 51
TERMINALS AND REFERENCE VALUE FOR
UNIFIED METER AND A/C AMP. ..................... ... 51
Self-diagnosis Function ....................................... ... 53
DESCRIPTION ................................................. ... 53
FUNCTION CONFIRMATION PROCEDURE ... ... 54
AUXILIARY MECHANISM: TEMPERATURE
SETTING TRIMMER ........................................ ... 59
AUXILIARY MECHANISM: FOOT POSITION
SETTING TRIMMER ........................................ ... 60
AUXILIARY MECHANISM: INLET PORT MEM-
ORY FUNCTION .............................................. ... 60
Operational Check ............................................... ... 61
CHECKING MEMORY FUNCTION .................. ... 61
CHECKING BLOWER ...................................... ... 61
CHECKING DISCHARGE AIR ......................... ... 61
CHECKING INTAKE AIR .................................. ... 62
CHECKING TEMPERATURE DECREASE ...... ... 62
CHECKING TEMPERATURE INCREASE ....... ... 62
CHECK A/C SWITCH ....................................... ... 62
CHECKING AUTO MODE ................................ ... 63
Power Supply and Ground Circuit for Auto Amp. ... 63 INSPECTION FLOW ........................................ ... 63
COMPONENT DESCRIPTION ......................... ... 64
DIAGNOSIS PROCEDURE FOR A/C SYSTEM ... 64
LAN System Circuit ............................................. ... 66
DIAGNOSIS PROCEDURE FOR LAN CIRCUIT ... 66
Mode Door Motor Circuit ..................................... ... 70
INSPECTION FLOW ........................................ ... 70
SYSTEM DESCRIPTION ................................. ... 71
COMPONENT DESCRIPTION ......................... ... 72
DIAGNOSIS PROCEDURE FOR MODE DOOR
MOTOR ............................................................ ... 72
Air Mix Door Motor Circuit ................................... ... 73
INSPECTION FLOW ........................................ ... 73 SYSTEM DESCRIPTION ..................................
... 74
COMPONENT DESCRIPTION ......................... ... 75
DIAGNOSIS PROCEDURE FOR AIR MIX DOOR
MOTOR ............................................................. ... 75
Air Mix Door Motor PBR Circuit ........................... ... 75
DIAGNOSIS PROCEDURE FOR AIR MIX DOOR
MOTOR PBR .................................................... ... 75
Intake Door Motor Circuit ..................................... ... 76
INSPECTION FLOW ......................................... ... 76
SYSTEM DESCRIPTION .................................. ... 77
COMPONENT DESCRIPTION ......................... ... 78
DIAGNOSIS PROCEDURE FOR INTAKE DOOR
MOTOR ............................................................. ... 78
Blower Motor Circuit ............................................. ... 79
INSPECTION FLOW ......................................... ... 79
SYSTEM DESCRIPTION .................................. ... 80
COMPONENT DESCRIPTION ......................... ... 81
DIAGNOSIS PROCEDURE FOR BLOWER
MOTOR ............................................................. ... 81
COMPONENT INSPECTION ............................ ... 83
Magnet Clutch Circuit ........................................... ... 84
INSPECTION FLOW ......................................... ... 84
SYSTEM DESCRIPTION .................................. ... 85
DIAGNOSIS PROCEDURE FOR MAGNET
CLUTCH ........................................................... ... 85
COMPONENT INSPECTION ............................ ... 90
Insufficient Cooling ............................................... ... 91
INSPECTION FLOW ......................................... ... 91
PERFORMANCE TEST DIAGNOSIS ............... ... 93
PERFORMANCE CHART ................................. ... 95
TROUBLE DIAGNOSIS FOR UNUSUAL PRES-
SURE ................................................................ ... 96
DIAGNOSIS PROCEDURE FOR INSUFFI-
CIENT COOLING .............................................. ... 98
Insufficient Heating .............................................. .100
INSPECTION FLOW ......................................... .100
Noise .................................................................... .101
INSPECTION FLOW ......................................... .101
Self-diagnosis ...................................................... .102
INSPECTION FLOW ......................................... .102
Memory Function ................................................. .103
INSPECTION FLOW ......................................... .103
Ambient Sensor Circuit ........................................ .104
COMPONENT DESCRIPTION ......................... .104
AMBIENT TEMPERATURE INPUT PROCESS .104
DIAGNOSIS PROCEDURE FOR AMBIENT
SENSOR ........................................................... .104
COMPONENT INSPECTION ............................ .106
In-vehicle Sensor Circuit ...................................... .107
COMPONENT DESCRIPTION ......................... .107
DIAGNOSIS PROCEDURE FOR IN-VEHICLE
SENSOR ........................................................... .108
COMPONENT INSPECTION ............................ .109
Sunload Sensor Circuit ........................................ .110
COMPONENT DESCRIPTION ......................... .110
SUNLOAD INPUT PROCESS .......................... .110
DIAGNOSIS PROCEDURE FOR SUNLOAD
SENSOR ........................................................... .110

ATC-104
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
Ambient Sensor CircuitAJS00154
COMPONENT DESCRIPTION
Ambient Sensor
The ambient sensor is attached on the hood lock stay. It detects
ambient temperature and converts it into a resistance value which is
then input into the unified meter and A/C amp.
AMBIENT TEMPERATURE INPUT PROCESS
The unified meter and A/C amp. includes a processing circuit for the ambient sensor input. However, when the
temperature detected by the ambient sensor increases quickly, the processing circuit retards the unified meter
and A/C amp. function. It only allows the unified meter and A/C amp. to recognize an ambient temperature
increase of 0.33 °C (0.6 °F) per 100 seconds.
As an example, consider stopping for a few minutes after high speed driving. Although the actual ambient tem-
perature has not changed, the temperature detected by the ambient sensor will increase. This is because the
heat from the engine compartment can radiate to the front grille area, location of the ambient sensor.
DIAGNOSIS PROCEDURE FOR AMBIENT SENSOR
SYMPTOM: Ambient sensor circuit is open or shorted. (21 or −21 is
indicated on unified meter and A/C amp. as a result of performing
self-diagnosis STEP-2.)
1. CHECK VOLTAGE BETWEEN AMBIENT SENSOR AND GROUND
1. Disconnect ambient sensor connector.
2. Turn ignition switch ON.
3. Check voltage between ambient sensor harness connector E34 terminal 1 (Y) and ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 4.
RJIA2016E
RJIA1461E
1 – Ground : Approx. 5 V
RJIA2017E

NAVIGATION SYSTEM AV-137
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
DIAGNOSIS BY HISTORY OF ERRORS
The “Self-diagnosis” results indicate whether an error occurred during the period from when the ignition switch
is turned to ON until “Self-diagnosis” is completed.
If an error occurred before the ignition switch was turned to ON and does not occur again until the “Self-diag-
nosis” is completed, the diagnosis result will be judged normal. Therefore, those errors in the past, which can-
not be found by the “Self-diagnosis”, must be found by diagnosing the “History of Errors”.
The History of Errors displays the time and place of the most recent occurrence of that error. However, take
note of the following points.

Correct time of the error occurrence may not be displayed when the GPS antenna substrate within the
NAVI control unit has malfunctioned.

Place of the error occurrence is represented by the position of the current-location mark at the time when
the error occurred. If the current-location mark has deviated from the correct position, then the place of
the error occurrence max be located correctly.

The maximum number of occurrences which can be stored is 50. For the 51st and later occurrences, the
displayed number remains 50.
When a reproducible malfunction occurred but its cause cannot be identified because several errors are
present, record the item, number and place (longitude/latitude) of error occurrence (or delete the History of
Errors), then turn the ignition switch from OFF to ON to reproduce the malfunction. Check the History of Errors
to find the items which show an increased number of occurrences, and diagnose the item.
Error item Possible causes
Example of symptom
Action/symptom
Gyro sensor
disconnected Communications malfunction between NAVI control unit and
internal gyro

Navigation location detection performance has
deteriorated.
(Angular velocity cannot be detected.)
Perform self-diagnosis.

When the NAVI control unit is judged normal by self-diagnosis,
the symptom may be intermittent, caused by strong radio inter-
ference.
GPS
disconnected Communication error between NAVI control unit and internal
GPS substrate

Navigation location detection performance has
deteriorated.
(Location correction using GPS is not per-
formed.)

GPS receiving status remains gray.

Perform self-diagnosis.

When the NAVI control unit is judged normal by self-diagnosis,
the symptom may be intermittent, caused by strong radio inter-
ference.
GPS
transmission
cable
malfunction Malfunctioning transmission wires to NAVI control unit and inter-
nal GPS substrate

During self-diagnosis, GPS diagnosis is not per-
formed.
Perform self-diagnosis.

When the NAVI control unit is judged normal by self-diagnosis,
the symptom may be intermittent, caused by strong radio inter-
ference.
GPS input
line
connection
error Malfunctioning receiving wires to NAVI control unit and internal
GPS substrate

Navigation location detection performance has
deteriorated.
(Location correction using GPS is not per-
formed.)

GPS receiving status remains gray.

Perform self-diagnosis.

When the NAVI control unit is judged normal by self-diagnosis,
the symptom may be intermittent, caused by strong radio inter-
ference.
GPS TCX0
over
GPS TCX0
under Oscillating frequency of the GPS substrate frequency synchro-
nizing oscillation circuit exceeded (or below) the specification

Navigation location detection performance has
deteriorated.
(Location correction using GPS is not per-
formed.)

GPS receiving status remains gray.

Perform self-diagnosis.

When the NAVI control unit is judged normal by self-diagnosis,
the symptom may be intermittent, caused by strong radio inter-
ference, or the control unit may have been subjected to exces-
sively high or low temperatures.

DI-1
DRIVER INFORMATION SYSTEM
K ELECTRICAL
CONTENTS
C
D E
F
G H
I
J
L
M
SECTION DI
A
B
DI
Revision: 2005 July 2005 FX
DRIVER INFORMATION SYSTEM
PRECAUTION ............................................................ 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 4
COMBINATION METERS ...................................... ..... 5
System Description ............................................. ..... 5
UNIFIED METER CONTROL UNIT ................. ..... 5
UNIFIED METER AND A/C AMP. .................... ..... 5
HOW TO CHANGE THE DISPLAY FOR ODO/
TRIP METER ................................................... ..... 6
POWER SUPPLY AND GROUND CIRCUIT ... ..... 6
SPEEDOMETER .............................................. ..... 7
TACHOMETER ................................................ ..... 7
WATER TEMPERATURE GAUGE ................... ..... 7
FUEL GAUGE .................................................. ..... 7
Component Parts and Harness Connector Location ..... 7
Arrangement of Combination Meter .................... ..... 8
Circuit Diagram ................................................... ..... 9
Wiring Diagram — METER — ............................. ... 10
Terminals and Reference Value for Combination
Meter ................................................................... ... 12
Terminals and Reference Value for Unified Meter
and A/C Amp. ...................................................... ... 13
Self-Diagnosis Mode of Combination Meter ........ ... 14
SELF-DIAGNOSIS FUNCTION ....................... ... 14
OPERATION PROCEDURE ............................ ... 14
CONSULT-II Function (METER A/C AMP) .......... ... 14
Trouble Diagnosis ............................................... ... 15
HOW TO PERFORM TROUBLE DIAGNOSIS ... 15
PRELIMINARY CHECK ................................... ... 15
Symptom Chart 1 ................................................ ... 17
Symptom Chart 2 ................................................ ... 17
Power Supply and Ground Circuit Inspection ..... ... 18
Vehicle Speed Signal Inspection ......................... ... 20
Engine Speed Signal Inspection ......................... ... 21
Engine Coolant Temperature Signal Inspection .. ... 21
Fuel Level Sensor Signal Inspection ................... ... 22
Odo/Trip Meter and Illumination Control Switch
Inspection ............................................................ ... 24
Fuel Gauge Pointer Fluctuates, Indicator Wrong Value or Varies ....................................................
... 24
Fuel Gauge Does Not Move to FULL Position .... ... 24
Electrical Components Inspection ....................... ... 25
CHECK FUEL LEVEL SENSOR UNIT ............. ... 25
Removal and Installation of Combination Meter .. ... 25
Disassembly and Assembly of Combination Meter ... 26
DISASSEMBLY ................................................ ... 26
ASSEMBLY ...................................................... ... 27
Removal and Installation of Odo/Trip Meter and Illu-
mination Control Switch ....................................... ... 27
REMOVAL ........................................................ ... 27
INSTALLATION ................................................ ... 27
UNIFIED METER AND A/C AMP ........................... ... 28
System Description .............................................. ... 28
INPUT/OUTPUT SIGNALS .............................. ... 28
FAIL-SAFE ....................................................... ... 29
CAN Communication System Description ........... ... 29
CAN Communication Unit .................................... ... 29
Schematic ............................................................ ... 30
CONSULT-II Function (METER A/C AMP) .......... ... 31
CONSULT-II BASIC OPERATION .................... ... 31
SELF-DIAGNOSTIC RESULTS ........................ ... 32
DATA MONITOR .............................................. ... 32
DTC [U1000] CAN Communication Circuit .......... ... 34
DTC [B2202] Meter Communication Circuit ........ ... 34
DTC [B2205] Vehicle Speed Circuit ..................... ... 37
Removal and Installation of Unified Meter and A/C
Amp. .................................................................... ... 37
REMOVAL ........................................................ ... 37
INSTALLATION ................................................ ... 37
COMPASS .............................................................. ... 38
System Description .............................................. ... 38
DIRECTION DISPLAY ...................................... ... 38
Wiring Diagram – COMPAS – ............................. ... 40
Removal and Installation of Compass ................. ... 41
WARNING LAMPS ................................................. ... 42
Schematic ............................................................ ... 42
Wiring Diagram — WARN — ............................... ... 43
Oil Pressure Warning Lamp Stays Off (Ignition
Switch ON) .......................................................... ... 51