2005 INFINITI FX35 oil

AT-84
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
53
Others Shift point is low in “D”
position. ON vehicle 1. Vehicle speed sensor A/T and vehicle speed sensor MTR
AT- 11 8
,
AT- 1 4 3
2. Accelerator pedal position sensor AT- 1 3 3
3. CAN communication lineAT- 1 0 6
4. Control valve with TCMAT- 2 4 3
54 Judder occurs during
lock-up. ON vehicle 1. A/T fluid level and state
AT- 5 2
2. Engine speed signalAT- 1 2 3
3. Turbine revolution sensorAT- 1 4 1
4. Vehicle speed sensor A/T and vehicle speed sensor MTR AT- 11 8,
AT- 1 4 3
5. Accelerator pedal position sensor AT- 1 3 3
6. CAN communication lineAT- 1 0 6
7. Torque converter clutch solenoid valveAT- 1 2 5
8. Control valve with TCMAT- 2 4 3
OFF vehicle 9. Torque converter AT- 2 9 0
55 Strange noise in “R”
position. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Engine speed signalAT- 1 2 3
3. CAN communication lineAT- 1 0 6
4. Control valve with TCMAT- 2 4 3
OFF vehicle 5. Torque converter
AT- 2 9 0
6. Oil pump assemblyAT- 3 0 8
7. Gear systemAT- 2 7 8
8. High and low reverse clutchAT- 3 2 3
9. Reverse brakeAT- 2 9 0
56 Strange noise in “N”
position. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Engine speed signalAT- 1 2 3
3. CAN communication lineAT- 1 0 6
4. Control valve with TCMAT- 2 4 3
OFF vehicle 5. Torque converter
AT- 2 9 06. Oil pump assemblyAT- 3 0 8
7. Gear systemAT- 2 7 8
No. Items Symptom Condition Diagnostic Item Reference
page

TROUBLE DIAGNOSIS AT-85
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX57
Others Strange noise in “D”
position. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Engine speed signalAT-123
3. CAN communication lineAT-106
4. Control valve with TCMAT-243
OFF vehicle 5. Torque converter
AT-290
6. Oil pump assemblyAT-308
7. Gear systemAT-278
8. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-18,
"Cross-Sectional View (2WD Models)" or AT-19, "Cross-
Sectional View (AWD Models)" ) AT-290
58 Vehicle does not
decelerate by engine
brake.
Refer to AT-231,
"Vehicle Does Not
Decelerate by Engine
Brake" . ON vehicle
1. PNP switch
AT- 11 4
2. A/T fluid level and state AT- 5 2
3. Control linkage adjustmentAT-235
4. Manual mode switchAT-170
5. ATF pressure switch 5AT-179
6. CAN communication lineAT-106
7. Control valve with TCMAT-243
OFF vehicle 8. Input clutch
AT-3139. High and low reverse clutchAT-323
10. Direct clutchAT-326
59 Engine brake does
not work M5 → M4. ON vehicle 1. PNP switch
AT- 11 4
2. A/T fluid level and state AT- 5 2
3. Control linkage adjustmentAT-235
4. Manual mode switchAT-170
5. ATF pressure switch 1AT-175
6. CAN communication lineAT-106
7. Control valve with TCMAT-243
OFF vehicle 8. Front brake (brake band) AT-290
60 Engine brake does
not work M4 → M3. ON vehicle 1. PNP switch
AT- 11 4
2. A/T fluid level and state AT- 5 2
3. Control linkage adjustmentAT-235
4. Manual mode switchAT-170
5. ATF pressure switch 1 and ATF pressure switch 3 AT-175,
AT-177
6. CAN communication line AT-106
7. Control valve with TCMAT-243
OFF vehicle 8. Front brake (brake band)
AT-2909. Input clutchAT-313
No. Items Symptom Condition Diagnostic Item Reference
page

AT-86
TROUBLE DIAGNOSIS
Revision: 2005 July 2005 FX
61
Others Engine brake does
not work M3 → M2. ON vehicle 1. PNP switch
AT- 11 4
2. A/T fluid level and state AT- 5 2
3. Control linkage adjustmentAT- 2 3 5
4. Manual mode switchAT- 1 7 0
5. ATF pressure switch 6AT- 1 8 1
6. CAN communication lineAT- 1 0 6
7. Control valve with TCMAT- 2 4 3
OFF vehicle 8. Front brake (brake band)
AT- 2 9 09. Input clutchAT- 3 1 3
10. High and low reverse clutchAT- 3 2 3
62 Engine brake does
not work M2 → M1. ON vehicle 1. PNP switch
AT- 11 4
2. A/T fluid level and state AT- 5 2
3. Control linkage adjustmentAT- 2 3 5
4. Manual mode switchAT- 1 7 0
5. ATF pressure switch 5AT- 1 7 9
6. CAN communication lineAT- 1 0 6
7. Control valve with TCMAT- 2 4 3
OFF vehicle 8. Input clutch
AT- 3 1 39. High and low reverse clutchAT- 3 2 3
10. Direct clutchAT- 3 2 6
63 Maximum speed low. ON vehicle
1. A/T fluid level and state
AT- 5 2
2. Line pressure testAT- 5 4
3. Accelerator pedal position sensorAT- 1 3 3
4. CAN communication lineAT- 1 0 6
5. Direct clutch solenoid valveAT- 1 5 8
6. Control valve with TCMAT- 2 4 3
OFF vehicle 7. Torque converter
AT- 2 9 0
8. Oil pump assemblyAT- 3 0 8
9. Input clutchAT- 3 1 3
10. Gear systemAT- 2 7 8
11. High and low reverse clutchAT- 3 2 3
12. Direct clutchAT- 3 2 6
13. Forward one-way clutch (Parts behind drum support is
impossible to perform inspection by disassembly. Refer to
AT-18, "
Cross-Sectional View (2WD Models)" or AT-19,
"Cross-Sectional View (AWD Models)" ) AT- 2 9 0
14. Forward brake (Parts behind drum support is impossible
to perform inspection by disassembly. Refer to AT-18,
"Cross-Sectional View (2WD Models)" or AT- 1 9 , "Cross-
Sectional View (AWD Models)" ) AT- 2 9 0
No. Items Symptom Condition Diagnostic Item
Reference
page

DTC P0745 LINE PRESSURE SOLENOID VALVE AT-129
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
DTC P0745 LINE PRESSURE SOLENOID VALVEPFP:31940
DescriptionACS002NB
The line pressure solenoid valve regulates the oil pump discharge pressure to suit the driving condition in
response to a signal sent from the TCM.
CONSULT-II Reference ValueACS003KU
On Board Diagnosis LogicACS002NC

This is an OBD-II self-diagnostic item.

Diagnostic trouble code “P0745 L/PRESS SOL/CIRC” with CONSULT-II or 4th judgement flicker without
CONSULT-II is detected under the following conditions.
–When TCM detects an improper voltage drop when it tries to operate the solenoid valve.
–When TCM detects as irregular by comparing target value with monitor value.
Possible CauseACS002ND

Harness or connectors
(Solenoid circuit is open or shorted.)

Line pressure solenoid valve
DTC Confirmation ProcedureACS002NE
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch ON. (Do not start engine.)
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for “A/T” with CONSULT-II.
3. Touch “START”.
4. Engine start and wait at least 5 seconds.
5. If DTC is detected, go to “ AT- 1 3 0 , "
Diagnostic Procedure" .
WITH GST
Follow the procedure “WITH CONSULT-II”.
Item name Condition Display value (Approx.)
LINE PRES SOL During driving 0.2 - 0.6 A
BCIA0031E

TROUBLE DIAGNOSIS FOR SYMPTOMS AT-195
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
In “P” Position, Vehicle Moves When PushedACS0080U
SYMPTOM:
Even though the selector lever is set in the “P” position, the parking mechanism is not actuated,
allowing the vehicle to be moved when it is pushed.
DIAGNOSTIC PROCEDURE
1. CHECK PNP SWITCH CIRCUIT
Perform self-diagnosis. Refer to AT- 9 3 , "
SELF-DIAGNOSTIC RESULT MODE" , AT- 1 0 3 , "TCM SELF-DIAG-
NOSTIC PROCEDURE (NO TOOLS)" .
Do the self-diagnostic results indicate PNP switch?
YES >> Check the malfunctioning system. Refer to AT- 11 4 , "DTC P0705 PARK/NEUTRAL POSITION
SWITCH" .
2. CHECK CONTROL LINKAGE
Check the control linkage.

Refer to AT- 2 3 5 , "Checking of A/T Position" .
OK or NG
OK >> GO TO 3.
NG >> Adjust control linkage. Refer to AT- 2 3 5 , "
Adjustment of
A/T Position" .
3. CHECK PARKING COMPONENTS
Check parking components. Refer to AT- 2 5 5 , "
Parking Components (2WD Models Only)" (2WD models) or
AT- 2 9 0 , "
Disassembly" (AWD models).
OK or NG
OK >> GO TO 4.
NG >> Repair or replace damaged parts.
4. CHECK A/T FLUID CONDITION
1. Remove oil pan. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sensor 2" .
2. Check A/T fluid condition. Refer to AT- 5 2 , "
A/T Fluid Condition
Check" .
OK or NG
OK >> INSPECTION END
NG >> Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to AT- 6 4 , "
Symp-
tom Chart" (Symptom No.65).
SCIA2119E
SCIA5199E

AT-196
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2005 July 2005 FX
In “N” Position, Vehicle MovesACS0080V
SYMPTOM:
Vehicle moves forward or backward when selecting “N” position.
DIAGNOSTIC PROCEDURE
1. CHECK PNP SWITCH CIRCUIT
Perform self-diagnosis. Refer to AT- 9 3 , "
SELF-DIAGNOSTIC RESULT MODE" , AT- 1 0 3 , "TCM SELF-DIAG-
NOSTIC PROCEDURE (NO TOOLS)" .
Do the self-diagnostic results indicate PNP switch?
YES >> Check the malfunctioning system. Refer to AT- 11 4 , "DTC P0705 PARK/NEUTRAL POSITION
SWITCH" .
NO >> GO TO 2.
2. CHECK CONTROL LINKAGE
Check the control linkage.

Refer to AT- 2 3 5 , "Checking of A/T Position" .
OK or NG
OK >> GO TO 3.
NG >> Adjust control linkage. Refer to AT- 2 3 5 , "
Adjustment of
A/T Position" .
3. CHECK A/T FLUID LEVEL
Check A/T fluid level. Refer to AT- 1 3 , "
Checking A/T Fluid" .
OK or NG
OK >> GO TO 4.
NG >> Refill ATF.
4. CHECK A/T FLUID CONDITION
1. Remove oil pan. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sensor 2" .
2. Check A/T fluid condition. Refer to AT- 5 2 , "
A/T Fluid Condition
Check" .
OK or NG
OK >> GO TO 5.
NG >> Check the malfunction items. If any items are damaged,
repair or replace damaged parts. Refer to AT- 6 4 , "
Symp-
tom Chart" (Symptom No.67).
SCIA2119E
SAT638A
SCIA5199E

AT-198
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2005 July 2005 FX
4. CHECK A/T FLUID LEVEL
Check the A/T fluid level. Refer to AT- 1 3 , "
Checking A/T Fluid" .
OK or NG
OK >> GO TO 5.
NG >> Refill ATF.
5. CHECK LINE PRESSURE
Check line pressure at idle with selector lever in “D” position. Refer
to AT- 5 4 , "
LINE PRESSURE TEST" .
OK or NG
OK >> GO TO 8.
NG - 1 >> Line pressure high: GO TO 6.
NG - 2 >> Line pressure low: GO TO 7.
6. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 9 0 , "
DISASSEMBLY" .
3. Check the following.
–Oil pump assembly. Refer to AT- 3 0 8 , "Oil Pump" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace damaged parts.
7. DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sen-
sor 2" .
2. Disassemble A/T. Refer to AT- 2 9 0 , "
DISASSEMBLY" .
3. Check the following.
–Oil pump assembly. Refer to AT- 3 0 8 , "Oil Pump" .
–Power train system. Refer to AT- 2 9 0 , "DISASSEMBLY" .
–Transmission case. Refer to AT- 2 9 0 , "DISASSEMBLY" .
OK or NG
OK >> GO TO 8.
NG >> Repair or replace damaged parts.
SAT638A
SAT494G

TROUBLE DIAGNOSIS FOR SYMPTOMS AT-199
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
8. CHECK A/T FLUID CONDITION
1. Remove oil pan. Refer to AT- 2 4 3 , "
Control Valve with TCM and A/T Fluid Temperature Sensor 2" .
2. Check A/T fluid condition. Refer to AT- 5 2 , "
A/T Fluid Condition
Check" .
OK or NG
OK >> GO TO 10.
NG >> GO TO 9.
9. DETECT MALFUNCTIONING ITEM

Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to AT- 6 4 ,
"Symptom Chart" (Symptom No.1).
OK or NG
OK >> GO TO 10.
NG >> Repair or replace damaged parts.
10. CHECK SYMPTOM
Check again. Refer to AT- 5 7 , "
Check at Idle" .
OK or NG
OK >> INSPECTION END
NG >> GO TO 11.
11 . CHECK TCM
1. Check TCM input/output signals. Refer to AT- 8 9 , "
TCM Input/Output Signal Reference Values" .
2. If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> INSPECTION END
NG >> Repair or replace damaged parts.
SCIA5199E