2005 INFINITI FX35 air

NAVIGATION SYSTEM AV-165
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Guide Sound Is Not HeardAKS007JY
1. CHECK VOICE GUIDE SETTING

While driving in the dark pink route, voice guide does not operate. (NOTE)

Is volume setting not switched ON?
NOTE:
Voice guide is only available at intersections that satisfy certain conditions. Therefore, guidance may not be
given even when the route on the map changes direction.
YES or NO
YES >> GO TO 2.
NO >> Switch the setting ON and turn the volume up.
2. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector and audio unit connector.
3. Check continuity between NAVI control unit and audio unit.
4. Check continuity between NAVI control unit and ground.
Ok or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK VOICE GUIDE
1. Connect NAVI control unit connector and audio unit connector.
2. Turn ignition switch ON.
3. Check signal between NAVI control unit harness connector B208 terminal 7 (LG) and 8 (PU) with CONSULT-ll or oscillo-
scope.
OK or NG
OK >> Replace audio unit.
NG >> Replace NAVI control unit.
Terminals
Continuity
NAVI control unit Audio unit
Connector Terminal
(Wire color) Connector Terminal
(Wire color)
B208 7 (LG)
M60 36 (B/R)
Ye s
8 (PU) 34 (W/R)
Terminals Continuity
NAVI control unit
—
Connector Terminal (Wire color)
B208 7 (LG)
Ground No
8 (PU)
PKIA2906E
7 (LG) - 8 (PU) : Refer to AV- 11 9 , "Terminals and Ref-
erence Value for NAVI Control Unit" .
PKIA2907E

AV-170
NAVIGATION SYSTEM
Revision: 2005 July 2005 FX
Driving TestAKS007KG
1. DRIVING TEST 1
1. Scroll the map screen to display the area to make correction. Press “ENTER” and select “CURRENT LOCATION CORRECTION”.
2. Correct direction of the vehicle mark.
3. Perform the distance correction of the CONFIRMATION/ADJUSTMENT mode. Note: Normally, adjustment is not necessary because this system has automatic distance correction func-
tion. However, when a tire chain is fitted, adjustment in accordance with the tire diameter ratio must be
made.
4. Are symptoms malfunctioning to the AV- 1 7 1 , "
Example of Symptoms Judged Not Malfunction" present
after driving the vehicle?
YES or NO
YES >> Limit of the location detection capacity of the navigation system.
NO >> GO TO 2.
2. DRIVING TEST 2
Did any malfunction occur when the proper test in the following test patterns is performed?

Test pattern
Driving test finds the difference between the symptoms monitored with and without each sensor.
–Test pattern 1: Test method with no GPS location correction
Disconnect GPS antenna connector (GT5) connected to the NAVI control unit. Accurately adjust the cur-
rent location and the direction, and then drive the vehicle.
–Test pattern 2: Test method with no map-matching
Accurately adjust the current location and the direction. Eject the map DVD-ROM from the NAVI control
unit with ignition switch turned to OFF, and then drive the vehicle. After driving, insert the map DVD-ROM
back in the unit, display the track of the vehicle on the map screen and compare it with the actual road
configuration.

Sample tests
– matching or by GPS>
Perform test pattern 1.
–;
Perform test pattern 1 and 2.
Compare the track of the vehicle on the map screen and the actual road configuration. For fairly accurate
tracking, plotting shall be made every several hundred meters.
–;
Perform test pattern 1 and 2.
Drive on a road of which distance is accurately known (by utilizing distance posts on a highway). Calculate
the rate of change (increased/decreased) of the distance by comparing with the actual distance.
Correction = A/B
A: Distance shown on the screen
B: Actual distance
YES or NO
YES >>
If adjustment is insufficient, perform adjustment again.

If any error is found in the map, please let us know.

Replace NAVI control unit.
NO >> Limit of the location detection capacity of the navigation system.

AV-176
NAVIGATION SYSTEM
Revision: 2005 July 2005 FX
Place In a parking lot When driving in a parking lot, or other loca-
tion where there are no roads on the map,
matching may place the vehicle mark on a
nearby road. When the vehicle returns to
the road, the vehicle mark may have devi-
ated from the correct location.
When driving in circle or turning the steer-
ing wheel repeatedly, direction errors accu-
mulate, and the vehicle mark may deviate
from the correct location.
If after traveling about 10km
(6miles) the correct location
has not been restored, perform
location correction and, if nec-
essary, direction correction.
Turn ta ble
When the ignition switch is OFF, the navi-
gation system cannot get the signal from
the gyroscope (angular speed sensor).
Therefore, the displayed direction may be
wrong and the correct road may not be
easily returned to after rotating the vehicle
on a turn table with the ignition OFF.
Slippery roads On snow, wet roads, gravel, or other roads where tires may slip easily, accumulated
mileage errors may cause the vehicle mark
to deviate from the correct road.
Slopes When parking in sloped garages, when traveling on banked roads, or in other
cases where the vehicle turns when tilted,
an error in the turning angle will occur, and
the vehicle mark may deviate from the
road.
Map data Road not displayed on the map screen
When driving on new roads or other roads
not displayed on the map screen, map
matching does not function correctly and
matches the location to a nearby road.
When the vehicle returns to a road which is
on the map, the vehicle mark may deviate
from the correct road.
Different road pattern
(Changed due to repair) If the road pattern stored in the map data
and the actual road pattern are different,
map matching does not function correctly
and matches the location to a nearby road.
The vehicle mark may deviate from the
correct road.
Vehicle Use of tire chains When tire chains are used, the mileage is
not correctly detected, and the vehicle
mark may deviate from the correct road. Drive the vehicle for a while. If
the distance is still deviated,
adjust it by using the distance
adjustment function. (If the tire
chain is removed, recover the
original value.)
Cause (condition) –: While driving ooo: Display Driving condition Remarks (correction, etc.)
SEL709V
SEL710V
SEL699V
ELK0201D

INFINITI MOBILE ENTERTAINMENT SYSTEM AV-189
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
DVD Player Does Not WorkAKS007WO
1. CHECK FUSE
Check that the following fuse of the DVD player are not blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown be sure to eliminate case of problem before installing new fuse, refer to PG-3,
"POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
Check voltage between connector terminals and ground as follows.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector between DVD player and fuse.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect DVD player connector.
3. Check continuity between the following DVD player harness connector B19 terminal 22 (B) and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or harness or connector.
4. CHECK HARNESS
1. Disconnect audio unit connector.
2. Check continuity between DVD player harness connector M73 terminal 9 (Y/B), 11 (L/W) and audio unit harness connector M65 terminal 38 (Y/B), 40 (L/W).
3. Check continuity between DVD player harness connector M73 terminal 9 (Y/B), 11 (L/W) and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
Unit Signal Fuse NO.
DVD player Battery power supply 32
ACC power supply 6
Terminals
Condition Reference value
(+)
(–)
Connector Terminal
(Wire color)
M73 16 (W/L)
Ground Ignition switch OFF Battery voltage
15 (LG/R) Ignition switch ACC Battery voltage
SKIB0323E
22 (B) – Ground : Continuity should exist.
SKIA5846E
9 (Y/B) - 38 (Y/B) : Continuity should exist.
11 (L/W) - 40 (L/W) : Continuity should exist.
9 (Y/B), 11 (L/W) - Ground : Continuity should not exist.

AV-192
INFINITI MOBILE ENTERTAINMENT SYSTEM
Revision: 2005 July 2005 FX
2. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect DVD display connector.
3. Check continuity between DVD player harness connector B19 terminal 21 (L), 31 (Y), 32 (R) and DVD display harness connec-
tor B192 terminal 5 (L), 15 (Y), 16 (R).
4. Check continuity between DVD player harness connector B19 terminal 21(L), 31 (Y), 32 (R) and ground.
5. Check continuity between DVD player harness connector B19 terminal 19 (LG), 27 (PU) and DVD display harness connector
B192 terminal 6(LG),10 (G), 12 (PU).
6. Check continuity between DVD player harness connector B19 terminal 19 (LG), 27 (PU) and ground.
OK or NG
OK >> Replace DVD display.
NG >> Repair harness or connector. 21 (L) – 5 (L) : Continuity should exist.
31 (Y) – 15 (Y) : Continuity should exist.
32 (R) – 16 (R) : Continuity should exist.
21 (L), 31 (Y), 32 (R)
– Ground : Continuity should not exist.
19 (LG) – 6 (LG) : Continuity should exist.
27 (PU)
– 10 (G),12 (PU) : Continuity should exist.
19 (LG), 27 (PU)
– Ground : Continuity should not exist.
SKIA7032E
PKIB6543E

INFINITI MOBILE ENTERTAINMENT SYSTEM AV-193
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Screen Is not Shown (Sounds Come Out of Both an Audio Speaker and a Head
Phone)
AKS007X1
1. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect DVD player connector and DVD display connector.
3. Check continuity between DVD player harness connector B19 terminal 23 (OR), 24 (W) and DVD display harness connector
B192 terminal 7 (OR), 8 (W).
4. Check continuity between DVD player harness connector B19 terminal 23(OR), 24 (W) and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2. CHECK VIDEO SIGNAL
1. Connect DVD player connector and DVD display connector.
2. Turn ignition switch ACC.
3. Check the signal between DVD player harness connector B19 terminal 23 (OR) and 24 (W) with CONSULT-II or oscilloscope.
OK or NG
OK >> GO TO 3.
NG >> Replace DVD player.
3. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect DVD player connector and DVD display connector.
3. Check continuity between DVD player harness connector B19 terminal 29 (GY) and DVD display harness connector B192 ter-
minal 13 (GY).
4. Check continuity between DVD player harness connector B19 terminal 29 (GY) and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector. 23 (OR) – 7 (OR) : Continuity should exist.
24 (W) – 8 (W) : Continuity should exist.
23 (OR), 24 (W)
– Ground : Continuity should not exist.
SKIA7044E
Terminal
Condition Reference value
(+) (–)
23 (OR) 24 (W) Play DVD video Refer to
AV-186, "
Terminals and
Reference Value for DVD Player" .
SKIA7050E
29 (GY) - 13 (GY) : Continuity should exist.
29 (GY) - Ground : Continuity should not exist.
SKIB0333E

AV-194
INFINITI MOBILE ENTERTAINMENT SYSTEM
Revision: 2005 July 2005 FX
4. CHECK DATA (DVD – LCD) SIGNAL
1. Connect DVD display connector and DVD player connector.
2. Turn ignition switch ACC.
3. Check voltage between DVD display harness connector B192 terminal 13 (GY) and ground.
OK or NG
OK >> Replace DVD display.
NG >> Replace DVD player.
Head Phone Does Not SoundAKS007WR
1. CHECK HEAD PHONE AND SIGNAL
Check the inspection items below to diagnose the malfunction.

Check that the signal is received at the rear seat.

Check that transmission part has any seals or dirt that interrupts
signal.

Check that the head phone battery has run down.
OK or NG
OK >> GO TO 2.
NG >>

Receive signal with head phone at the rear seat.

Remove seal or dirt that is interrupting signal.

If the battery has run down, replace it with new one.
2. CHECK HEAD PHONE
Check that sound is heard with another head phone.
OK or NG
OK >> Replace malfunction head phone.
NG >> GO TO 3.
3. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect DVD player connector and DVD display connector.
3. Check continuity between DVD player harness connector B19 terminal 17 (G), 18 (L), 19 (LG), 20 (Y) and DVD display harness
connector B192 terminal 1 (G), 2 (L), 3, 4 (Y).
4. Check continuity between DVD player harness connector B19 terminal 17 (G), 18 (L), 19 (LG), 20 (Y) and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector. 13 (GY)
– Ground : Refer to
AV- 1 8 6 , "
Terminals and
Reference Value for DVD Player" .
SKIB0334E
SKIA5852E
17 (G) – 1 (G) : Continuity should exist.
18 (L) – 2 (L) : Continuity should exist.
19 (LG) – 3 : Continuity should exist.
20 (Y) – 4 (Y) : Continuity should exist.
17 (G), 18 (L), 19 (LG),
20 (Y) – Ground : Continuity should not exist.
SKIA7033E

AV-196
INFINITI MOBILE ENTERTAINMENT SYSTEM
Revision: 2005 July 2005 FX
3. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect DVD player connector and DVD display connector.
3. Check continuity between DVD player harness connector B19 terminal 30 (BR) and DVD display harness connector B192 ter-
minal 14 (BR).
4. Check continuity between DVD player harness connector B19 terminal 30 (BR) and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair harness or connector.
4. CHECK DATA (LCD – DVD) SIGNAL
1. Connect DVD display connector.
2. Turn ignition switch ACC.
3. Check the signal between DVD player harness connector B19 terminal 30 (BR) and ground.
OK or NG
OK >> Replace DVD player.
NG >> Replace DVD display.
No CD·DVD Sound From All SpeakersAKS007WS
1. VERIFY THE PHENOMENON
1. Turn ignition switch ACC.
2. Turn on the radio, receive radio program, check that the sound is heard from all the speakers.
OK or NG
OK >> GO TO 2.
NG >> Replace audio unit.
2. CHECK A/C AND AV SWITCH SELF-DIAGNOSIS
A/C and AV switch self-diagnosis. Check “REAR AV” switch. Refer to AV- 3 7 , "
A/C and AV Switch Self-Diagno-
sis Function" .
OK or NG
OK >> GO TO 3.
NG >> Replace A/C and AV switch. 30 (BR) – 14 (BR) : Continuity should exist.
30 (BR) – Ground : Continuity should not exist.
SKIB0335E
30 (BR)
– Ground : Refer to
AV- 1 8 6 , "Terminals and
Reference Value for DVD Player" .
SKIA7043E