2005 INFINITI FX35 relay

LAN-4Revision: 2005 July 2005 FX
fied Meter and A/C Amp. Circuit ..........................
.422
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit .................................................................. .422
ECM Circuit Inspection ........................................ .423
TCM Circuit Inspection ........................................ .423
Display Unit Circuit Inspection ............................. .424
Data Link Connector Circuit Inspection ............... .424
BCM Circuit Inspection ........................................ .425
Steering Angle Sensor Circuit Inspection ............ .425
Unified Meter and A/C Amp. Circuit Inspection ... .426
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................ .426
IPDM E/R Circuit Inspection ................................ .427
CAN Communication Circuit Inspection ............... .428
IPDM E/R Ignition Relay Circuit Inspection ......... .433
CAN SYSTEM (TYPE 10) ...................................... .434
Component Parts and Harness Connector Location .434
Schematic ............................................................ .435
Wiring Diagram - CAN - ....................................... .436
Check Sheet ........................................................ .439 CHECK SHEET RESULTS (EXAMPLE) ...........
.441
Inspection Between TCM and Data Link Connector
Circuit ................................................................... .456
Inspection Between Data Link Connector and Uni-
fied Meter and A/C Amp. Circuit .......................... .457
Inspection Between Unified Meter and A/C Amp.
and ABS Actuator and Electric Unit (Control Unit)
Circuit ................................................................... .457
ECM Circuit Inspection ........................................ .458
TCM Circuit Inspection ......................................... .458
Display Unit Circuit Inspection ............................. .459
AWD Control Unit Circuit Inspection .................... .459
Data Link Connector Circuit Inspection ................ .460
BCM Circuit Inspection ........................................ .460
Steering Angle Sensor Circuit Inspection ............. .461
Unified Meter and A/C Amp. Circuit Inspection .... .461
ABS Actuator and Electric Unit (Control Unit) Circuit
Inspection ............................................................. .462
IPDM E/R Circuit Inspection ................................ .462
CAN Communication Circuit Inspection ............... .463
IPDM E/R Ignition Relay Circuit Inspection .......... .469

CAN SYSTEM (TYPE 1) LAN-69
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
Case 16
Check IPDM E/R ignition relay circuit continuously sticks “OFF”. Refer to LAN-84, "IPDM E/R Ignition Relay
Circuit Inspection" .
PKIB4456E

LAN-70
[CAN]
CAN SYSTEM (TYPE 1)
Revision: 2005 July 2005 FX
Case 17
Check IPDM E/R ignition relay circuit continuously sticks “ON”. Refer to LAN-84, "IPDM E/R Ignition Relay Cir-
cuit Inspection" .
Inspection Between TCM and Data Link Connector CircuitAKS00CFO
1. CHECK HARNESS FOR OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Disconnect ECM connector and harness connector M82.
4. Check continuity between harness connector M82 terminals 14H (L), 15H (R) and data link connector M5 terminals 6 (L), 14
(R).
OK or NG
OK >> Connect all the connectors and diagnose again. Refer to LAN-7, "
TROUBLE DIAGNOSES WORK FLOW" .
NG >> Repair harness.
PKIB4457E
14H (L) - 6 (L) : Continuity should exist.
15H (R) - 14 (R) : Continuity should exist.
SKIA6861E

LAN-84
[CAN]
CAN SYSTEM (TYPE 1)
Revision: 2005 July 2005 FX
IPDM E/R Ignition Relay Circuit InspectionAKS00CG4
Check the following. If no malfunction is found, replace the IPDM E/R.

IPDM E/R power supply circuit. Refer to PG-28, "IPDM E/R Power/Ground Circuit Inspection" .

Ignition power supply circuit. Refer to PG-12, "IGNITION POWER SUPPLY - IGNITION SW. IN “ON”
AND/OR “START”" .

CAN SYSTEM (TYPE 2) LAN-109
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
Case 17
Check IPDM E/R ignition relay circuit continuously sticks “OFF”. Refer to LAN-125, "IPDM E/R Ignition Relay
Circuit Inspection" .
PKIB4439E

LAN-110
[CAN]
CAN SYSTEM (TYPE 2)
Revision: 2005 July 2005 FX
Case 18
Check IPDM E/R ignition relay circuit continuously sticks “ON”. Refer to LAN-125, "IPDM E/R Ignition Relay
Circuit Inspection" .
Inspection Between TCM and Data Link Connector CircuitAKS00CF2
1. CHECK HARNESS FOR OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Disconnect ECM connector and harness connector M82.
4. Check continuity between harness connector M82 terminals 14H (L), 15H (R) and data link connector M5 terminals 6 (L), 14
(R).
OK or NG
OK >> Connect all the connectors and diagnose again. Refer to LAN-7, "
TROUBLE DIAGNOSES WORK FLOW" .
NG >> Repair harness.
PKIB4440E
14H (L) - 6 (L) : Continuity should exist.
15H (R) - 14 (R) : Continuity should exist.
SKIA6861E

CAN SYSTEM (TYPE 2) LAN-125
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
18. CHECK UNIT REPRODUCIBILITY
Performs the following procedure for each unit, and then perform reproducibility test.
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Disconnect the unit connector.
4. Connect the battery cable to the negative terminal.
5. Make sure that the symptom filled in the “Symptom” of the check sheet is reproduced. (Do not confuse it with the symptom related to removed unit.)
6. Make sure that the same symptom is reproduced.
–A/T assembly
–Display unit
–BCM
–Steering angle sensor
–LDW camera unit
–Unified meter and A/C amp.
–ABS actuator and electric unit (control unit)
–Driver seat control unit
–ECM
–IPDM E/R
Check results
Reproduce>>Install removed unit, and then check the other unit.
Not reproduced>>Replace removed unit.
IPDM E/R Ignition Relay Circuit InspectionAKS00CFJ
Check the following. If no malfunction is found, replace the IPDM E/R.

IPDM E/R power supply circuit. Refer to PG-28, "IPDM E/R Power/Ground Circuit Inspection" .

Ignition power supply circuit. Refer to PG-12, "IGNITION POWER SUPPLY - IGNITION SW. IN “ON”
AND/OR “START”" .

CAN SYSTEM (TYPE 3) LAN-153
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
Case 19
Check IPDM E/R ignition relay circuit continuously sticks “OFF”. Refer to LAN-170, "IPDM E/R Ignition Relay
Circuit Inspection" .
PKIB4421E