2005 INFINITI FX35 audio

NAVIGATION SYSTEM AV-165
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Guide Sound Is Not HeardAKS007JY
1. CHECK VOICE GUIDE SETTING

While driving in the dark pink route, voice guide does not operate. (NOTE)

Is volume setting not switched ON?
NOTE:
Voice guide is only available at intersections that satisfy certain conditions. Therefore, guidance may not be
given even when the route on the map changes direction.
YES or NO
YES >> GO TO 2.
NO >> Switch the setting ON and turn the volume up.
2. CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect NAVI control unit connector and audio unit connector.
3. Check continuity between NAVI control unit and audio unit.
4. Check continuity between NAVI control unit and ground.
Ok or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK VOICE GUIDE
1. Connect NAVI control unit connector and audio unit connector.
2. Turn ignition switch ON.
3. Check signal between NAVI control unit harness connector B208 terminal 7 (LG) and 8 (PU) with CONSULT-ll or oscillo-
scope.
OK or NG
OK >> Replace audio unit.
NG >> Replace NAVI control unit.
Terminals
Continuity
NAVI control unit Audio unit
Connector Terminal
(Wire color) Connector Terminal
(Wire color)
B208 7 (LG)
M60 36 (B/R)
Ye s
8 (PU) 34 (W/R)
Terminals Continuity
NAVI control unit
—
Connector Terminal (Wire color)
B208 7 (LG)
Ground No
8 (PU)
PKIA2906E
7 (LG) - 8 (PU) : Refer to AV- 11 9 , "Terminals and Ref-
erence Value for NAVI Control Unit" .
PKIA2907E

AV-166
NAVIGATION SYSTEM
Revision: 2005 July 2005 FX
Screen Is Not ShownAKS007JZ
1. CHECK POWER SUPPLY AND GROUND CIRCUIT
Check power supply and ground circuit. Refer to AV- 1 4 4 , "
Power Supply and Ground Circuit Check for Dis-
play" .
OK or NG
OK >> Replace display.
NG >> Check the malfunctioning parts.
Audio Screen Is Not Shown (NAVI Screen Is Shown)AKS007K0
1. CHECK 1: COMMUNICATION LINE
Check audio communication line. Refer to AV- 1 5 0 , "
Audio Communication Line Check (Between Display Con-
trol Unit and Audio Unit)" .
OK or NG
OK >> GO TO 2.
NG >> Check the malfunctioning parts.
2. CHECK 2: COMMUNICATION LINE
Check display communication line. Refer to AV- 1 5 2 , "
Display Communication Line Check (Between Display
Control Unit and Display)" .
OK or NG
OK >> Replace display.
NG >> Check the malfunctioning parts.
A/C Screen Is Not Shown (NAVI Screen Is Shown)AKS007K1
1. CHECK CAN COMMUNICATION LINE
Check CAN communication line. Refer to AV- 1 5 5 , "
CAN Communication Line Check" .
OK or NG
OK >> GO TO 2.
NG >> After filling out CAN DIAG SUPPORT MONITOR check sheet, GO TO LAN-5, "
Precautions When
Using CONSULT-II" .
2. CHECK COMMUNICATION LINE
Check display communication line. Refer to AV- 1 5 2 , "
Display Communication Line Check (Between Display
Control Unit and Display)" .
OK or NG
OK >> Replace display.
NG >> Check the malfunctioning parts.
TRIP, FUEL ECON and MAINTENANCE Screens Are Not ShownAKS007K2
1. CHECK IGNITION SIGNAL
Check ignition signal. Refer to AV- 1 4 8 , "
Ignition Signal Check for Display Control Unit" .
OK or NG
OK >> GO TO 2.
NG >> Check the malfunctioning parts.
2. CHECK POWER SUPPLY AND GROUND CIRCUIT
Check power supply circuit for display. Refer to AV- 1 4 4 , "
Power Supply and Ground Circuit Check for Display"
.
OK or NG
OK >> GO TO 3.
NG >> Check the malfunctioning parts.

NAVIGATION SYSTEM AV-171
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Example of Symptoms Judged Not MalfunctionAKS007KH
BASIC OPERATION
VEHICLE MARK
Symptom Cause Remedy
No image is shown. Display brightness adjustment is set fully to DARK side. Adjust the display brightness.
No guide sound is heard.
Audio guide volume is too low or
too high. Volume control is set to OFF, MIN or MAX. Adjust the audio guide volume.
Audio guidance is not available while the vehicle
is driving on a dark pink route. System is not malfunction.
Screen is too dark.
Motion of the image is too slow. Temperature inside the vehicle is low. Wait until the temperature inside the vehicle
reaches the proper temperature.
Small black or bright spots appear
on the screen. Symptom peculiar to a liquid crystal display. System is not malfunction.
Symptom Cause Remedy
Map screen and BIRDVIEW™
Name of the place vary with the
screen. Some thinning of the character data is done to
prevent the display becoming to complex. In
some cases and in some locations, the display
contents may differ.
The same place name, street name, etc. may not
be displayed every time on account of the data
processing. System is not malfunction.
Vehicle mark is not positioned cor-
rectly. Vehicle is transferred by ferry or by towing after its
ignition switch is turned to OFF. Drive the vehicle for a while in the GPS sat-
ellite signal receiving condition.
Screen will not switch to nighttime
mode after the lighting switch is
turned ON. The daytime screen is selected by the “SWITCH
SCREENS” when the last time the screen dim-
ming setting is done.
Switching between daytime/nighttime screens
may be inhibited by the automatic illumination
adjustment function. Perform screen dimming and select the
nighttime screen by “SWITCH SCREENS”.
Map screen will not scroll in accor-
dance with the vehicle travel. Current location is not displayed. Press “MAP” button to display the current
location.
Vehicle mark will not be shown. Current location is not displayed. Press “MAP” button to display the current location.
Accuracy indicator (GPS satellite
mark) on the map screen stays
gray. GPS satellite signal is intercepted because the
vehicle is in or behind a building. Move the vehicle out to an open space.
GPS satellite signal cannot be received because
an obstacle is placed on top of the display. Do not place anything in the center on top of
the display.
GPS satellites are located badly. Wait until the location becomes better.
Vehicle location accuracy is low. Accuracy indicator (GPS satellite mark) on the map screen stays gray. Current location is not determined.
Vehicle speed setting by the vehicle speed pulse
has been deviated (advanced or retarded) from
the actual vehicle speed because tire chain is fit-
ted or the system has been used on another vehi-
cle. Drive the vehicle for a while [for approx. 30
minutes at approx. 30 km/h (19 MPH)] and
the deviation will be automatically adjusted.
If advancement or retard still occur, perform
the distance adjustment by CONFIRMA-
TION/ADJUSTMENT mode of diagnosis
function.
Map data has error or omission. (Vehicle mark is
always deviated to the same position.) As a rule, an updated map DVD-ROM will be
released once a year.

AV-180
NAVIGATION SYSTEM
Revision: 2005 July 2005 FX
Removal and Installation of NAVI Control UnitAKS007O9
REMOVAL
1. Remove passenger side seat. Refer to SE-100, "Removal and Installation"
2. Remove clips (4), and remove NAVI control unit cover.
3. Remove screws (2) and nut (1) with power tool, and remove NAVI control unit.
4. Remove screws (4) with power tool and remove bracket.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of GPS AntennaAKS007OA
REMOVAL
1. Remove audio unit. Refer to AV- 4 7 , "Removal and Installation of
Audio Unit" .
2. Remove screw (1) and remove GPS antenna.
INSTALLATION
Installation is the reverse order of removal.
PKIA3129E
SKIA5822E
SKIA5823E
SKIA5824E

NAVIGATION SYSTEM AV-181
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
Removal and Installation of A/C and AV SwitchAKS007OB
For A/C and AV switch removal and installation procedures, refer to AV- 4 8 , "Removal and Installation for A/C
and AV Switch" .
Removal and Installation of Display UnitAKS007OC
For display unit removal and installation procedures, refer to AV- 4 7 , "Removal and Installation of Audio Unit" .
Removal and Installation of Display Control UnitAKS007OD
REMOVAL
1. Remove instrument passenger lower panel. Refer to IP-11,
"Removal and Installation" .
2. Remove screws (2) with power tool and remove display control unit.
3. Remove screws (4) with power tool and remove bracket.
INSTALLATION
Installation is the reverse order of removal.
SKIA5825E
SKIA5826E

AV-182
INFINITI MOBILE ENTERTAINMENT SYSTEM
Revision: 2005 July 2005 FX
INFINITI MOBILE ENTERTAINMENT SYSTEMPFP:28184
System DescriptionAKS007WH
Refer to Owner's Manual for mobile entertainment system operating instructions.
Power is supplied at all times

through 15A fuse (No. 32, located in the fuse and fusible link block)

to DVD player terminal 16

through DVD player terminals 31 and 32

to DVD display terminals 15 and 16.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in the fuse block (J/B)]

to DVD player terminal 15

through DVD player terminal 21

to DVD display terminal 5.
Ground is supplied

to DVD player terminal 22

through body ground B15 and B45

to DVD player terminals 19, 27

through DVD display terminals 6, 10 and 12.
When DVD player power switch is ON, power is supplied

through DVD player terminal 9

to audio unit terminal 38 and

through audio unit terminal 40

to DVD player terminal 11.
When DVD player power switch is ON, DVD sound signals are supplied

through DVD player terminals 17, 18, and 20

to DVD display terminals 1, 2 and 4.
DVD sound can be heard by the head phone.
When rear AV switch is ON, audio signals are supplied

through DVD player terminals 1, 2, 3, and 4

to audio unit terminals 37, 39, 43, and 42.
DVD sound can be heard from the speaker.
When DVD player power switch is ON, video signals are supplied

through DVD player terminals 23 and 24

to DVD display terminals 7 and 8.
When remote controller is operated, operation signals are supplied

through DVD display terminal 14

to DVD player terminal 30 and

through DVD player terminal 29

to DVD display terminal 13.

AV-186
INFINITI MOBILE ENTERTAINMENT SYSTEM
Revision: 2005 July 2005 FX
Terminals and Reference Value for DVD PlayerAKS007WJ
Terminal
(Wire color) Item Signal
input/
output Condition
Reference value Example of
symptom
(+) (–) Ignition
switch Operation
1 (L) 2 (R) MES output
signal (LH)
Output ACC Rear AV
switch is ON No sound
from speaker LH
3 (LG) 4 (PU) MES output
signal (RH) No sound
from speaker RH
8—Shield —— — — —
9
(Y/B) Ground Audio ON sig-
nal (MES - H/
U) Output ACC Push “POWER”
switch of DVD
player Approx. 5 V
System dose not
work properly.
10
(R/Y) Ground Illumination
control signal Input OFF Illumination con-
trol switch is oper-
ated by lighting
switch in 1st posi-
tion. Changes between approx. 0 V
and approx. 12 V. DVD display illumi-
nation cannot be
controlled.
11
(L/W) Ground Control sig-
nal (H/U -
MES) Input ACC Push “POWER”
switch of DVD
player Approx. 5 V
System dose not
work properly.
12
(R/L) Ground Illumination
signal Input OFF Lighting switch is
ON (1st position). Approx. 12 V DVD display illumi-
nation dose not
come on when light-
ing switch is ON (1st
position).
Lighting switch
OFF. Approx. 0 V
15
(LG/R) GroundACC power
supply Input ACC — Battery voltage System does not
work properly.
16
(W/L) Ground
Battery power
supply Input OFF — Battery voltage
System dose not
work properly.
17 (G) 19 (LG) MES output
signal (Com-
mon) Output ACC
Play CD or DVD
video Approx. 0 V —
18 (L) 19 (LG) MES output
signal (L+) Output ACC
Play CD or DVD
video No sound from head
phone LH
19 (LG) Ground Ground — ON — Approx. 0 V —
20 (Y) 19 (LG) MES output
signal (R+) Output ACC Play CD or DVD
video No sound from head
phone RH
21 (L) Ground ACC power
supply Output ACC — Approx. 5 V Display does not
work properly.
22 (B) Ground Ground — ON — Approx. 0 V —
SKIA0177E
SKIA5828E
SKIA5828E

INFINITI MOBILE ENTERTAINMENT SYSTEM AV-189
C
D E
F
G H
I
J
L
M A
B
AV
Revision: 2005 July 2005 FX
DVD Player Does Not WorkAKS007WO
1. CHECK FUSE
Check that the following fuse of the DVD player are not blown.
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown be sure to eliminate case of problem before installing new fuse, refer to PG-3,
"POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
Check voltage between connector terminals and ground as follows.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector between DVD player and fuse.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect DVD player connector.
3. Check continuity between the following DVD player harness connector B19 terminal 22 (B) and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or harness or connector.
4. CHECK HARNESS
1. Disconnect audio unit connector.
2. Check continuity between DVD player harness connector M73 terminal 9 (Y/B), 11 (L/W) and audio unit harness connector M65 terminal 38 (Y/B), 40 (L/W).
3. Check continuity between DVD player harness connector M73 terminal 9 (Y/B), 11 (L/W) and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
Unit Signal Fuse NO.
DVD player Battery power supply 32
ACC power supply 6
Terminals
Condition Reference value
(+)
(–)
Connector Terminal
(Wire color)
M73 16 (W/L)
Ground Ignition switch OFF Battery voltage
15 (LG/R) Ignition switch ACC Battery voltage
SKIB0323E
22 (B) – Ground : Continuity should exist.
SKIA5846E
9 (Y/B) - 38 (Y/B) : Continuity should exist.
11 (L/W) - 40 (L/W) : Continuity should exist.
9 (Y/B), 11 (L/W) - Ground : Continuity should not exist.