2005 Citroen C4 ESP

Downloaded from www.Manualslib.com manuals search engine 183
ENGINE
BELT TENSION CORRESPONDANCE TABLE / SEEM UNITS
!
4099-T (C.TRONIC.105)@Tools #4122-T (C.TRONIC.105.5) !
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 183

Downloaded from www.Manualslib.com manuals search engine 186
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: KFW - NFV
Refitting the timing belt.
NOTE :Check that the pegs [1]and [2]are in place.
WARNING: Respect the direction of fitting of the belt: The arrows "a" indicate the direction of rotation of
the crankshaft.
Position:
-The timing belt, belt "b"well-tensioned in the following order: Crankshaft pinion, camshaft pulley, coolant pump
pulley, tensioner roller.
- Tool [5]
(respect the direction of fitting relative to the valve timing).
- Put the tensioner roller in contact with the belt.
- Tighten the nut (2).
Pre-tensioning the belt.
Place tool [4] on the tensioned part "b"of the belt.
Slacken the screw (2).
Turn the roller (3)in the anti-clockwise direction using the drive square, to obtain a value of: 44 SEEMunits.
Tighten the nut (2) to 2 m.daN.
Remove tools [1], [2] and [4].
Rotate the crankshaft 4 turnsin the normal direction of rotation.
IMPERATIVE: Never turn the crankshaft backwards.
B1EP06AC
B1EP069C
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 186

Downloaded from www.Manualslib.com manuals search engine 187
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: KFW - NFV
Pre-tensioning the timing belt (continued).
Make sure of the timing setting by refitting the pegs [1]and [2].
Remove the valve cover.
Position the tool [5]
(respect the direction of fitting relative to the valve timing).
Adjusting the belt tension.
Place tool [4]on the tensioned part of the belt.
Slacken the nut (2).
Detension the belt, but too much.
Tension the timing belt to obtain a value of: 31 ± 2 SEEMunits.
Tighten the nut (2)to 2 m.daN.
Remove tools [1], [2], [4] and [5].
Checking the belt tension.
Rotate the crankshaft 2 turnsin the normal direction of rotation.
Check that it is still possible to peg the following components.
Flywheel.
Camshaft.
IMPERATIVE: Repeat the belt tensioning operation if the pegging is not possible.
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 187

Downloaded from www.Manualslib.com manuals search engine 188
ENGINECHECKING THE VALVE TIMING
Engine: KFU
Tools.
[1] Flywheel setting peg: 4507-TA. Toolkit 4507-T
[2] Camshaft setting peg: 4533-TA.C1
[3] Camshaft setting peg: (-).0194.A
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking.
Deconnect the battery.
Remove:
- The engine cover.
- The upper timing cover (1).
- The oil filter (2).
Remove the sparking plugs to facilitate rotation of the engine.
Turn the engine by means of the crankshaft screw.
IMPERATIVE: Never turn the engine backwards.
Suspend the engine.
Remove:
- The screws (3), the upper RH engine support (4)and the screws (5).
B1BP37JC
B1BP37KC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 188

Downloaded from www.Manualslib.com manuals search engine 190
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Tools.
[1]Flywheel setting peg: 4507-T.A
[2]Camshaft setting peg: 4533-T.AC1
[3] Camshaft setting peg: (-).0194.A
[4] Belt retaining pin: 4533-TA.D
IMPERATIVE: Respect the safety and cleanliness requirements.
Setting the timing.
Raise and support the vehicle, wheels hanging.
Disconnect the battery.
Remove the engine cover.
Raise and support the vehicle, wheels hanging.
Remove:
- The accessories drive belt (3)
(see corresponding operation).
- The crankshaft pulley, the engine cover.
- The upper timing cover (1).
- The oil filter (2).
Remove the sparking plugs to facilitate rotation of the engine.
Suspend the engine.
Remove the screws (4), the upper RH engine support (5)and the screws (6).
B1BP37QD
B1BP37RC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 190

Downloaded from www.Manualslib.com manuals search engine 194
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Setting the valve timing.
Loosen the screw (2), remove the belt.
Loosen the six pulley screws (1)on the hubs
(there should be a slight amount of friction between the screws and
the pinions).
Check that the rollers (2)and (3) rotate freely.
NOTE: The belt bears three identification marks (a), (b)and (c), facing its own teeth (1), (52)and (72)respectively
(identification marks = white paint lines on the back of the belt facing the corresponding teeth).
Refit the belt.
Line up mark (A)on the belt with groove (D)of the pinion (4).
Hold the belt against the pinion (4).
B1EP11EC
B1EP11DC
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 194

Downloaded from www.Manualslib.com manuals search engine 197
ENGINE
CHECKING THE VALVE TIMING
Engine: NFU
Tools.
[1]Flywheel setting peg: 4507-T.A Toolkit 4507-T
[2a]Camshaft setting peg: 4533-TA.C1
[3b]Camshaft setting peg: 4533-TA.C2
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking.
Disconnect the negative terminal of the battery.
Remove:
- The oil filter (1).
- Suspend the engine.
Remove:
- The engine support (2)and the upper timing cover (3).
B1BP2M7C
B1BP381C
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 197

Downloaded from www.Manualslib.com manuals search engine ENGINE
198
CHECKING THE VALVE TIMING
Engine: NFU
Remove the sparking plugs, to facilitate rotation of the crankshaft.
Rotate the engine by means of the crankshaft pinion screw
(clockwise)to bring it to the pegging
position.
Fit the tools [2a]and [2b].
Peg the flywheel, using tool [1].
NOTE:If the setting proves impossible, restart the timing setting operation.
Remove the tools [1], [2a]and [2b].
Complete the refitting.
IMPERATIVE: Carry out the operations that are necessary following a reconnection of the
battery
(see corresponding operation).
B1EP170C
B1BP2MBC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 198