2005 Citroen C4 screen

Downloaded from www.Manualslib.com manuals search engine GENERAL
3
IDENTIFICATION OF THE VEHICLE
E1AP08WD
A- Manufacturer's name plate (estate).
B -Chassis stamp, cold stamp.
C -Manufacturer's name plate (saloon).
D -Label:
(label affixed to the front pillar on driver's side)
- Tyre pressures.
- RP organisation no.
- Paint code.
E - Serial number (visible through the windscreen).
F -Engine legislation type - Factory serial no.
G - Gearbox ident. reference - Factory serial no.
XSARA
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 3

Downloaded from www.Manualslib.com manuals search engine GENERALGENERAL
5
IDENTIFICATION OF THE VEHICLEXSARA PICASSO
E1AP088D
A- Chassis stamp
(cold stamp on bodywork).
B -Chassis no. reminder
(label located at bottom of windscreen right hand side).
C -Manufacturer's data plate
(located at bottom of RH central pillar).
D -Label:
(located on front LH door inner panel)
- Tyre pressures.
- Tyre identification.
- Spare wheel identification.
E -Label:
(located on fuse box cover)
- Factory code.
- A-S / RP N°.
- Paint code.
F -Gearbox identification ref.
G -Engine legislation type - Factory serial number.
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 5

Downloaded from www.Manualslib.com manuals search engine 9
GENERAL
OPERATIONS TO BE CARRIED OUT AFTER A REPAIR
IMPERATIVE: All these operations are to be performed following a reconnection of the battery.
Antiscanning function.
It is necessary to wait 1 minuteafter the battery has been disconnected in order to be able to start the vehicle.
Electric windows.
It may be necessary to re-initialise the sequential and anti-pinch functions.
NOTE: If the window is open at the time the battery is reconnected, action the window switch several times to close it, then re-initialise.
Open the window fully.
Action and release the window switch until the window is completely closed.
NOTE:This operation has to be carried out on each electric window.
Multifunction screen.
It is necessary to adjust the date, time and outside temperature.
Reconfigure the personalisation menu of the multifunction screen.
Radio.
Reprogramme the radio stations.
Telematic unit (radiotelephone RT3).
Reprogramme the radio stations.
Warning: the vehicle has to be in the open air
(on switching on the ignition, the ECU searches for satellites).
Reprogramme the customer parameters.
C4
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 9

Downloaded from www.Manualslib.com manuals search engine 38
GENERAL
SCREEN WASH FLUID
GREASING
General use
All countriesConcentrated: 250ml
Fluid ready
to use9980 33
9980 06
9980 05ZC 9875 953U
ZC 9875 784U
ZC 9885 077U9980 56
ZC 9875 279U Packs
CITROËN Part No.
LUBRICANTS - TOTAL recommended oils
1Litre
5Litres
Norms NLGI
2
TOTAL MULTIS 2
TOTAL SMALL MECHANISMS All countries
Note: NLGI= National Lubrificating Grease Institude.
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 38

Downloaded from www.Manualslib.com manuals search engine 371
AXLES
SUSPENSION
STEERING
C4CHECKING THE POWER STEERING ASSISTANCE PRESSURE
Tools.
[1]Pressure gauge: (-).0710.AZ
[2]Checking tube: pressure gauge to tap: (-).0710.B1
[3]Checking tube: high pressure pipe to tap: (-).0710.B2
[4]Checking tube: high pressure pump to tap: (-).0710.B3
[5]3-way tap: (-).0710.C
[6]Union: (-).0710.J
[7]Union: (-).0710.K
[8] Plugs for checking valve sealing: (-).0710.H
Precautions to be taken.
Work with care to avoid entry of polluting particles into the circuit.
NOTE:The correct operation of the system requires perfect cleanliness of the fluid and of the
hydraulic components.
Check:
- The level of the power steering fluid.
- The condition of the piping and unions.
Using the tools.
Prepare the checking assembly [1], [2], [3], [4], [5], [6]and [7].
Attach the tool [1].
Remove the front RH wheel, the splash-shield and the screen wash reservoir.
B3EP16CC
B3EP16DC
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 371

Downloaded from www.Manualslib.com manuals search engine 373
AXLES
SUSPENSION
STEERING
CHECKING THE POWER STEERING ASSISTANCE PRESSURE
Checking the valve sealing.
Remove the under-engine shield.
Move aside the heat shield from the steering mechanism.
Slacken the unions (2)on the power steering ram.
Uncouple the two supply pipes (3)from the distributor valve and move them aside.
Fit on the distributor valve the two plugs [8], tighten to 0,8 m.daN.
Move the steering slowly from lock to lock, to drain the ram.
Top up the level of the power steering fluid.
Open the tap [5].
Stop the engine.
Maintain the engine speed at accelerated idle.
Hold the wheels on full lock, first on one side then on the other.
The pressure should adjust to 105 ± 5 bars.
The pressure is correct: replace the steering mechanism.
The pressure is lower than the values above: replace the distributor valve.
Couple the two supply pipes (3)on the distributor valve; tighten to 0,8 m.daN.
Retighten the unions (2)on the power steering ram; tighten to 0,8 m.daN.
Remove the union [7]on the high pressure pipe (1)and the union [6]on the power steering
electropump.
Refit:
- the high pressure pipe (1); tighten to 2 ± 0,2 m.daN.
- the screen wash reservoir, the front RH splash-shield and the front RH wheel.
B3EP16FC
B3EP16GC
C4
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 373