2005 Citroen BERLINGO Diesel

Downloaded from www.Manualslib.com manuals search engine 136
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Flywheel
Flywheel4,8 ± 0,4
Clutch mechanism2 ± 0,2
Lubrication circuit
Oil pump1,6 ± 0,2
Coolant oil heat exchanger7 ± 0,7
Turbocharger lubrication pipe
Engine end4,8 ± 0,4
Turbocharger end2,2 ± 0,2
Injection circuit
Injector fixing flange nut3 ± 0,3
Unions on fuel high pressure common injection rail2 ± 0,2
Injection pump on support2,3 ± 0,2
Union on diesel injector2 ± 0,2
Injection pump pulley5 ± 0,5
Union on fuel high pressure pump2 ± 0,2
Cooling circuit
Coolant pump1,5 ± 0,1
Coolant inlet housing1,8 ± 0,1 Engines: RHY - RHZ
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 136

Downloaded from www.Manualslib.com manuals search engine 146
ENGINESPECIAL FEATURES - TIGHTENING TORQUES (m.daN)
Injection circuit
28 High pressure pipe union on injector 2,5 ± 0,2
Diesel injector nuts
29Do up both nuts by hand
Tightening0,4 ± 0,3
Angular tightening45°±5°
30 Fuel high pressure pump screw 2,25 ± 0,3
31 High pressure pipe union on fuel high pressure pump 2,5 ± 0,2
32 Fuel high pressure supply common rail nuts 3 ± 0,3
33 Union on fuel high pressure supply common rail 2,5 ± 0,2
Engine: RHR
B1HP22LD
C4
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 146

Downloaded from www.Manualslib.com manuals search engine 154
ENGINEAUXILIARY EQUIPMENT DRIVE BELT
Engines: All Types Petrol and Diesel
Tools.
- Belt tension measuring instrument: 4122 - T (C.TRONIC 105.5).
WARNING: If using tool 4099-T (C.TRONIC 105).
Essential.
- Before refitting the auxiliary equipment drive belt, check that:
- 1 / The roller(s) rotate freely (no play or stiffness).
- 2 / The belt is correctly engaged in the grooves of the various pulleys.
Angl.-t2-page135-239-2005 9/01/06 10:13 Page 154

Downloaded from www.Manualslib.com manuals search engine 165
ENGINE
XSARA
AUXILIARY EQUIPMENT DRIVE BELT
Tools.
[1] Dynamic tensioner compression lever: (-).0188.Z
[2] Peg for dynamic tensioner roller: (-).0194.F
Removing.
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure
Diesel injection (HDi) engine versions.
Remove:
- the front RH wheel.
- the sound insulation under the engine.
- the splash-shield.
WARNING: Mark the direction of fitting of the accessories belt if it is to be re-used.
Compress the dynamic tensioner roller (1)by acting at «a»
(clockwise), using tool [1].
Peg at «b». using tool [2].
Keep the dynamic tensioner roller (1)compressed and remove the auxiliaries drive belt.
IMPERATIVE: Check that the rollers (1) and (2) can turn freely
(without play and without
tight spots).
B1BP2VZD
Engines: 8HX - 8HZ
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 165

Downloaded from www.Manualslib.com manuals search engine 167
ENGINE
B1EP18UD
B1BP3ACD
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 9HX - 9HY - 9HZ
Tools.
[1]Dynamic tensioner roller lever (DV6 TED4engine): (-).0194-E3
[1a]Dynamic tensioner roller lever (DV6 ATED4engine): (-).0194-E1
[1b]Lever extension (DV6 ATED4engine): (-).0194-E2
[2] Dynamic tensioner roller locking peg: (-).0194-F
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure
Diesel injection (HDi) engine versions.
Markings on the dynamic tensioner roller.
«a»position «maximum wear»of the auxiliaries drive belt.
«b»Nominal position.
Removing.
WARNING: Mark the direction of fitting of the auxiliaries drive belt in the case of re-use of
the belt.
Compress the dynamic tensioner roller (1)by acting at «c»
(clockwise), using tool [1].
Peg using tool [2]at «d».
Keep the dynamic tensioner roller (1)compressed and remove the auxiliaries drive belt.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 167

Downloaded from www.Manualslib.com manuals search engine 240
ENGINECHECKING THE VALVE TIMING
Engines: 9HX - 9HY - 9HZ
Tools.
[1]Flywheel setting peg: (-).0194.C
[2] Camshaft setting peg: (-).0194.B
[3] Crankshaft setting peg: (-).0194.A
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure Diesel
injection (HDi) engine versions.
Checking and setting the timing.
Raise and support the vehicle, wheels hanging.
Disconnect the battery.
Uncouple:
- The fuel supply unions (1).
- The air/air heat exchanger inlet and outlet pipes (3).
- The exhaust line at the catalytic converter flexible pipe.
- Disconnect the connecteur at «a».
Remove the accessories drive belt
(see corresponding operation).
Support the engine with a roller jack equipped with a block.
Remove the four screws (5), the three screws (4)and the engine supports (3).
B1BP38TD
B1BP38UD
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 240

Downloaded from www.Manualslib.com manuals search engine 243
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HX - 9HY - 9HZ
Tools.
[1] Flywheel setting peg: (-).0194.C
[2]Camshaft setting peg: (-).0194.B
[3]Crankshaft setting peg: (-).0194.A
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure Diesel
injection (HDi) engine versions.
Checking and setting the timing.
Raise and support the vehicle, wheels hanging.
Disconnect the battery.
Uncouple:
- The fuel supply unions (1).
- The air/air heat exchanger inlet and outlet pipes (3).
- The exhaust line at the flexible pipe.
- Disconnect the connecteur at «a».
Remove the accessories drive belt
(see corresponding operation).
Support the engine with a roller jack equipped with a block.
Remove the four screws (5), the three screws (4)and the engine supports (3).
B1BP38TD
B1BP38UD
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 243

Downloaded from www.Manualslib.com manuals search engine 260
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: WJY
B1BP2FTC
Setting the timing.
Removing.
Disconnect the battery.
Remove the front RH lower splash-shield, using tool [1].
Remove the accessories drive belt
(see corresponding operation).Uncouple and plug the diesel fuel delivery and return hoses.
Support the engine, using a workshop hoist.
Remove the RH engine support.
Engage 5th gearto permit rotation of the engine.
Remove the upper cover (1).
Remove the intermediate cover (2).
Remove the lower cover (3).
WARNING: Refit the screw (4) equipped with a washer
(5 mm thick).
Rotate the front RH wheel to drive the engine in its normal direction of
rotation.
Bring the camshaft drive and injection pump pinions to their setting
points.
Position the peg [2]
(from underneath the vehicle).
Continue turning the engine until the peg [2]engages in the flywheel.
B1BP30BC
XSARA
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 260