2005 CHRYSLER VOYAGER Frame

ON-BOARD DIAGNOSTICS
TABLE OF CONTENTS
page page
TASK MANAGER
DESCRIPTION.........................25OPERATION...........................25
TASK MANAGER
DESCRIPTION
The PCM is responsible for efficiently coordinating
the operation of all the emissions-related compo-
nents. The PCM is also responsible for determining if
the diagnostic systems are operating properly. The
software designed to carry out these responsibilities
is call the ªTask Managerº.
OPERATION
The Task Manager determines when tests happen
and when functions occur. Many of the diagnostic
steps required by OBD II must be performed under
specific operating conditions. The Task Manager soft-
ware organizes and prioritizes the diagnostic proce-
dures. The job of the Task Manager is to determine if
conditions are appropriate for tests to be run, moni-
tor the parameters for a trip for each test, and record
the results of the test. Following are the responsibil-
ities of the Task Manager software:
²Test Sequence
²MIL Illumination
²Diagnostic Trouble Codes (DTCs)
²Trip Indicator
²Freeze Frame Data Storage
²Similar Conditions Window
Test Sequence
In many instances, emissions systems must fail
diagnostic tests more than once before the PCM illu-
minates the MIL. These tests are known as 'two trip
monitors.' Other tests that turn the MIL lamp on
after a single failure are known as 'one trip moni-
tors.' A trip is defined as 'start the vehicle and oper-
ate it to meet the criteria necessary to run the given
monitor.'
Many of the diagnostic tests must be performed
under certain operating conditions. However, there
are times when tests cannot be run because another
test is in progress (conflict), another test has failed
(pending) or the Task Manager has set a fault that
may cause a failure of the test (suspend).
²Pending
Under some situations the Task Manager will notrun a monitor if the MIL is illuminated and a fault is
stored from another monitor. In these situations, the
Task Manager postpones monitorspendingresolu-
tion of the original fault. The Task Manager does not
run the test until the problem is remedied.
For example, when the MIL is illuminated for an
Oxygen Sensor fault, the Task Manager does not run
the Catalyst Monitor until the Oxygen Sensor fault is
remedied. Since the Catalyst Monitor is based on sig-
nals from the Oxygen Sensor, running the test would
produce inaccurate results.
²Conflict
There are situations when the Task Manager does
not run a test if another monitor is in progress. In
these situations, the effects of another monitor run-
ning could result in an erroneous failure. If thiscon-
flictis present, the monitor is not run until the
conflicting condition passes. Most likely the monitor
will run later after the conflicting monitor has
passed.
For example, if the Fuel System Monitor is in
progress, the Task Manager does not run the catalyst
Monitor. Since both tests monitor changes in air/fuel
ratio and adaptive fuel compensation, the monitors
will conflict with each other.
²Suspend
Occasionally the Task Manager may not allow a two
trip fault to mature. The Task Manager willsus-
pendthe maturing of a fault if a condition exists
that may induce an erroneous failure. This prevents
illuminating the MIL for the wrong fault and allows
more precise diagnosis.
For example, if the PCM is storing a one trip fault
for the Oxygen Sensor and the catalyst monitor, the
Task Manager may still run the catalyst Monitor but
will suspend the results until the Oxygen Sensor
Monitor either passes or fails. At that point the Task
Manager can determine if the catalyst system is
actually failing or if an Oxygen Sensor is failing.
MIL Illumination
The PCM Task Manager carries out the illumina-
tion of the MIL. The Task Manager triggers MIL illu-
mination upon test failure, depending on monitor
failure criteria.
RSON-BOARD DIAGNOSTICS25-25

The Task Manager Screen shows both a Requested
MIL state and an Actual MIL state. When the MIL is
illuminated upon completion of a test for a good trip,
the Requested MIL state changes to OFF. However,
the MIL remains illuminated until the next key
cycle. (On some vehicles, the MIL will actually turn
OFF during the thirdgood trip) During the key cycle
for the third good trip, the Requested MIL state is
OFF, while the Actual MIL state is ON. After the
next key cycle, the MIL is not illuminated and both
MIL states read OFF.
Diagnostic Trouble Codes (DTCs)
With OBD II, different DTC faults have different
priorities according to regulations. As a result, the
priorities determine MIL illumination and DTC era-
sure. DTCs are entered according to individual prior-
ity. DTCs with a higher priority overwrite lower
priority DTCs.
Priorities
²Priority 0 ÐNon-emissions related trouble codes.
²Priority 1 Ð One trip failure of a two trip fault
for non-fuel system and non-misfire. (MIL Off)
²Priority 2 Ð One trip failure of a two trip fault
for fuel system (rich/lean) or misfire. (MIL Off)
²Priority3ÐTwotrip failure for a non-fuel sys-
tem and non-misfire or matured one trip comprehen-
sive component fault. (MIL On)
²Priority4ÐTwotrip failure or matured fault
for fuel system (rich/lean) and misfire or one trip cat-
alyst damaging misfire. Catalyst damage misfire is a
2 trip MIL. The MIL flashes on the first trip when
catalyst damage misfire levels are present. (MIL On)
Non-emissions related failures have no priority.
One trip failures of two trip faults have low priority.
Two trip failures or matured faults have higher pri-
ority. One and two trip failures of fuel system and
misfire monitor take precedence over non-fuel system
and non-misfire failures.
DTC Self Erasure
With one trip components or systems, the MIL is
illuminated upon test failure and DTCs are stored.
Two trip monitors are components requiring failure
in two consecutive trips for MIL illumination. Upon
failure of the first test, the Task Manager enters a
maturing code. If the component fails the test for a
second time the code matures and a DTC is set.
After three good trips the MIL is extinguished and
the Task Manager automatically switches the trip
counter to a warm-up cycle counter. DTCs are auto-
matically erased following 40 warm-up cycles if the
component does not fail again.
For misfire and fuel system monitors, the compo-
nent must pass the test under a Similar Conditions
Window in order to record a good trip. A Similar Con-ditions Window is when engine RPM is within  375
RPM and load is within  20% of when the fault
occurred.
NOTE: It is important to understand that a compo-
nent does not have to fail under a similar window of
operation to mature. It must pass the test under a
Similar Conditions Window when it failed to record
a Good Trip for DTC erasure for misfire and fuel
system monitors.
DTCs can be erased anytime with a scan tool.
Erasing the DTC with the scan tool erases all OBD
II information. The scan tool automatically displays a
warning that erasing the DTC will also erase all
OBD II monitor data. This includes all counter infor-
mation for warm-up cycles, trips and Freeze Frame.
Trip Indicator
TheTripis essential for running monitors and
extinguishing the MIL. In OBD II terms, a trip is a
set of vehicle operating conditions that must be met
for a specific monitor to run. All trips begin with a
key cycle.
Good Trip
The Good Trip counters are as follows:
²Global Good Trip
²Fuel System Good Trip
²Misfire Good Trip
²Alternate Good Trip (appears as a Global Good
Trip on scan tool)
²Comprehensive Components
²Major Monitor
²Warm-Up Cycles
Global Good Trip
To increment a Global Good Trip, the Oxygen sen-
sor and Catalyst efficiency monitors must have run
and passed, and 2 minutes of engine run time.
Fuel System Good Trip
To count a good trip (three required) and turn off
the MIL, the following conditions must occur:
²Engine in closed loop
²Operating in Similar Conditions Window
²Short Term multiplied by Long Term less than
threshold
²Less than threshold for a predetermined time
If all of the previous criteria are met, the PCM will
count a good trip (three required) and turn off the
MIL.
Misfire Good Trip
If the following conditions are met the PCM will
count one good trip (three required) in order to turn
off the MIL:
²Operating in Similar Condition Window
²1000 engine revolutions with no misfire
25 - 26 ON-BOARD DIAGNOSTICSRS
TASK MANAGER (Continued)

Alternate Good Trip
Alternate Good Trips are used in place of Global
Good Trips for Comprehensive Components and
Major Monitors. If the Task Manager cannot run a
Global Good Trip because a component fault is stop-
ping the monitor from running, it will attempt to
count an Alternate Good Trip.
The Task Manager counts an Alternate Good Trip
for Comprehensive components when the following
conditions are met:
²Two minutes of engine run time, idle or driving
²No other faults occur
The Task Manager counts an Alternate Good Trip
for a Major Monitor when the monitor runs and
passes. Only the Major Monitor that failed needs to
pass to count an Alternate Good Trip.
Warm-Up Cycles
Once the MIL has been extinguished by the Good
Trip Counter, the PCM automatically switches to a
Warm-Up Cycle Counter that can be viewed on the
scan tool. Warm-Up Cycles are used to erase DTCs
and Freeze Frames. Forty Warm-Up cycles must
occur in order for the PCM to self-erase a DTC and
Freeze Frame. A Warm-Up Cycle is defined as fol-
lows:
²Engine coolant temperature must start below
and rise above 160É F
²Engine coolant temperature must rise by 40É F
²No further faults occur
Freeze Frame Data Storage
Once a failure occurs, the Task Manager records
several engine operating conditions and stores it in a
Freeze Frame. The Freeze Frame is considered one
frame of information taken by an on-board data
recorder. When a fault occurs, the PCM stores the
input data from various sensors so that technicians
can determine under what vehicle operating condi-
tions the failure occurred.
The data stored in Freeze Frame is usually
recorded when a system fails the first time for two
trip faults. Freeze Frame data will only be overwrit-
ten by a different fault with a higher priority.
CAUTION: Erasing DTCs, either with the scan tool;
or by disconnecting the battery, also clears all
Freeze Frame data.
Similar Conditions Window
The Similar Conditions Window displays informa-
tion about engine operation during a monitor. Abso-
lute MAP (engine load) and Engine RPM are stored
in this window when a failure occurs. There are two
different Similar conditions Windows: Fuel System
and Misfire.FUEL SYSTEM
²Fuel System Similar Conditions WindowÐ
An indicator that 'Absolute MAP When Fuel Sys Fail'
and 'RPM When Fuel Sys Failed' are all in the same
range when the failure occurred. Indicated by switch-
ing from 'NO' to 'YES'.
²Absolute MAP When Fuel Sys FailÐ The
stored MAP reading at the time of failure. Informs
the user at what engine load the failure occurred.
²Absolute MAPÐ A live reading of engine load
to aid the user in accessing the Similar Conditions
Window.
²RPM When Fuel Sys FailÐ The stored RPM
reading at the time of failure. Informs the user at
what engine RPM the failure occurred.
²Engine RPMÐ A live reading of engine RPM
to aid the user in accessing the Similar Conditions
Window.
²Adaptive Memory FactorÐ The PCM utilizes
both Short Term Compensation and Long Term Adap-
tive to calculate the Adaptive Memory Factor for
total fuel correction.
²Upstream O2S VoltsÐ A live reading of the
Oxygen Sensor to indicate its performance. For
example, stuck lean, stuck rich, etc.
²SCW Time in Window (Similar Conditions
Window Time in Window)Ð A timer used by the
PCM that indicates that, after all Similar Conditions
have been met, if there has been enough good engine
running time in the SCW without failure detected.
This timer is used to increment a Good Trip.
²Fuel System Good Trip CounterÐATrip
Counter used to turn OFF the MIL for Fuel System
DTCs. To increment a Fuel System Good Trip, the
engine must be in the Similar Conditions Window,
Adaptive Memory Factor must be less than cali-
brated threshold and the Adaptive Memory Factor
must stay below that threshold for a calibrated
amount of time.
²Test Done This TripÐ Indicates that the
monitor has already been run and completed during
the current trip.
MISFIRE
²Same Misfire Warm-Up StateÐ Indicates if
the misfire occurred when the engine was warmed up
(above 160É F).
²In Similar Misfire WindowÐ An indicator
that 'Absolute MAP When Misfire Occurred' and
'RPM When Misfire Occurred' are all in the same
range when the failure occurred. Indicated by switch-
ing from 'NO' to 'YES'.
²Absolute MAP When Misfire OccurredÐ
The stored MAP reading at the time of failure.
Informs the user at what engine load the failure
occurred.
RSON-BOARD DIAGNOSTICS25-27
TASK MANAGER (Continued)

AJAR SWITCH - EXPORT -INSTALLATION, HOOD .................8Q-3
AJAR SWITCH - EXPORT - REMOVAL, HOOD .............................. 8Q-3
ALIGNMENT - DESCRIPTION, WHEEL ......2-47
ALIGNMENT - EXPORT - STANDARD PROCEDURE, FRONT FOG LAMP UNIT .....8L-9
ALIGNMENT - EXPORT - STANDARD PROCEDURE, HEADLAMP UNIT .........8L-15
ALIGNMENT - STANDARD PROCEDURE, FRONT FOG LAMP UNIT ................8L-9
ALIGNMENT - STANDARD PROCEDURE, FRONT WIPER ARM ................... 8R-9
ALIGNMENT - STANDARD PROCEDURE, HEADLAMP UNIT ..................... 8L-14
ALIGNMENT - STANDARD PROCEDURE, WHEEL ............................. 2-52
ALIGNMENT, SPECIFICATIONS - WHEEL ....2-56
AMBIENT TEMP SENSOR - DESCRIPTION . 8M-12
AMBIENT TEMP SENSOR - OPERATION . . 8M-12
AMBIENT TEMPERATURE SENSOR CIRCUIT, DIAGNOSIS AND TESTING .....8M-12
AMBIENT TEMPERATURE SENSOR, DIAGNOSIS AND TESTING .............8M-12
AMPLIFIER - INSTALLATION .............8A-7
AMPLIFIER - REMOVAL ................8A-7
AN AIRBAG DEPLOYMENT - STANDARD PROCEDURE, SERVICE AFTER ...........8O-7
ANCHOR - DESCRIPTION, CHILD RESTRAINT .......................... 8O-9
ANCHOR - OPERATION, CHILD RESTRAINT .......................... 8O-10
ANTENNA - EXPORT - DESCRIPTION, QUARTER GLASS INTEGRAL ............8A-13
ANTENNA - EXPORT - OPERATION, QUARTER GLASS INTEGRAL ............8A-13
ANTENNA - NAVIGATION RADIO - INSTALLATION ....................... 8A-11
ANTENNA - NAVIGATION RADIO - REMOVAL .......................... 8A-11
ANTENNA BODY AND CABLE - DESCRIPTION ........................ 8A-7
ANTENNA BODY AND CABLE - OPERATION .......................... 8A-7
ANTENNA BODY AND CABLE, DIAGNOSIS AND TESTING ..............8A-8
ANTENNA CABLE - INSTALLATION, INSTRUMENT PANEL .................8A-12
ANTENNA CABLE - REMOVAL, INSTRUMENT PANEL .................8A-12
ANTENNA, EXPORT - QUARTER GLASS INTEGRAL .......................... 8A-13
ANTENNA MODULE - EXPORT - DESCRIPTION ....................... 8A-10
ANTENNA MODULE - EXPORT - OPERATION ......................... 8A-10
ANTENNA MODULE, EXPORT ...........8A-10
ANTILOCK BRAKE - DESCRIPTION, CONTROLLER ........................ 8E-4
ANTILOCK BRAKE - INSTALLATION, CONTROLLER ........................ 8E-6
ANTILOCK BRAKE - OPERATION, CONTROLLER ........................ 8E-5
ANTILOCK BRAKE - REMOVAL, CONTROLLER ........................ 8E-5
ANTILOCK BRAKE SYSTEM - DESCRIPTION ........................ 5-87
ANTILOCK BRAKE SYSTEM - OPERATION . . 5-88
ANTILOCK BRAKE SYSTEM BLEEDING - STANDARD PROCEDURE ................5-90
ANTILOCK BRAKE SYSTEM (EXPORT) - DESCRIPTION ........................ 5-87
A-PILLAR LOWER EXTENSION TRIM - INSTALLATION ....................... 23-79
A-PILLAR LOWER EXTENSION TRIM - REMOVAL .......................... 23-79
A-PILLAR TRIM - INSTALLATION ........23-79
A-PILLAR TRIM - REMOVAL ............23-79
A-PILLAR-HEADER, OR B-PILLAR - INSTALLATION ....................... 23-17
A-PILLAR-HEADER, OR B-PILLAR - REMOVAL .......................... 23-17
APPLIQUE - INSTALLATION .............23-14
APPLIQUE - REMOVAL ................23-14
ARM - DESCRIPTION, LOWER CONTROL . . . 2-12
ARM - INSPECTION, LOWER CONTROL ....2-14
ARM - INSTALLATION, LOWER CONTROL . . 2-15
ARM - INSTALLATION, REAR WIPER .....8R-10 ARM - OPERATION, LOWER CONTROL
.....2-12
ARM - REMOVAL, LOWER CONTROL ......2-12
ARM - REMOVAL, REAR WIPER .........8R-10
ARM ALIGNMENT - STANDARD PROCEDURE, FRONT WIPER ............8R-9
ARM (REAR BUSHING - HYDRO) - ASSEMBLY, LOWER CONTROL ...........2-15
ARM (REAR BUSHING - HYDRO) - DISASSEMBLY, LOWER CONTROL ........2-13
ARM (REAR BUSHING - STANDARD) - ASSEMBLY, LOWER CONTROL ...........2-14
ARM (REAR BUSHING - STANDARD) - DISASSEMBLY, LOWER CONTROL ........2-13
ARMREST - INSTALLATION ............23-108
ARMREST - REMOVAL ...............23-108
ARMREST - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION ..............23-130
ARMREST - SECOND ROW - FOLD-IN- FLOOR - REMOVAL .................. 23-130
ARMREST ROTATING ASSEMBLY - SECOND ROW - FOLD-IN-FLOOR -
INSTALLATION ...................... 23-130
ARMREST ROTATING ASSEMBLY - SECOND ROW - FOLD-IN-FLOOR -
REMOVAL ......................... 23-130
ARMS - DESCRIPTION, ROCKER ........9-112
ARMS - INSPECTION, ROCKER ...........9-35
ARMS - INSTALLATION, FRONT WIPER ....8R-9
ARMS - INSTALLATION, ROCKER .........9-35
ARMS - OPERATION, ROCKER ..........9-112
ARMS - REMOVAL, FRONT WIPER .........8R-9
ARMS - REMOVAL, ROCKER .............9-35
ARMS AND SHAFT - ASSEMBLY, ROCKER ............................ 9-113
ARMS AND SHAFT - DISASSEMBLY, ROCKER ............................ 9-113
ARMS AND SHAFT - INSTALLATION, ROCKER ............................ 9-113
ARMS AND SHAFT - REMOVAL, ROCKER . . 9-112
ASSIST DISPLAY - DESCRIPTION, PARK . . . 8B-3
ASSIST DISPLAY - INSTALLATION, PARK . . . 8B-4
ASSIST DISPLAY - OPERATION, PARK .....8B-3
ASSIST DISPLAY - REMOVAL, PARK ......8B-4
ASSIST HANDLE - INSTALLATION ........23-79
ASSIST HANDLE - REMOVAL ...........23-79
ASSIST MODULE - DESCRIPTION, PARK . . . 8B-4
ASSIST MODULE - INSTALLATION, PARK . . 8B-6
ASSIST MODULE - OPERATION, PARK .....8B-5
ASSIST MODULE - REMOVAL, PARK ......8B-5
ASSIST SENSOR - DESCRIPTION, PARK . . . 8B-6
ASSIST SENSOR - INSTALLATION, PARK . . . 8B-6
ASSIST SENSOR - OPERATION, PARK .....8B-6
ASSIST SENSOR - REMOVAL, PARK ......8B-6
ASSIST STRAP - INSTALLATION, FRONT SEAT BACK ........................ 23-112
ASSIST STRAP - REMOVAL, FRONT SEAT BACK ........................ 23-112
ATTACHED - INSTALLATION, EXTERIOR NAME PLATES - ADHESIVE .............23-51
ATTACHED - INSTALLATION, EXTERIOR NAME PLATES - TAPE .................23-51
ATTACHED - REMOVAL, EXTERIOR NAME PLATES - ADHESIVE .................. 23-51
ATTACHED - REMOVAL, EXTERIOR NAME PLATES - TAPE ...................... 23-51
AUDIO/VIDEO - DESCRIPTION ...........8A-1
AUDIO/VIDEO, DIAGNOSIS AND TESTING . . 8A-2
AUTO SHUT DOWN RELAY - DESCRIPTION ......................... 8I-3
AUTO SHUT DOWN RELAY - OPERATION . . . 8I-3
AUTOMATIC ADJUSTER - DIAGNOSIS AND TESTING, DRUM BRAKE ............5-14
AUTOMATIC ADJUSTER TENSION RELEASE - STANDARD PROCEDURE,
PARKING BRAKE ...................... 5-63
AUTOMATIC ADJUSTER TENSION RESET - STANDARD PROCEDURE, PARKING
BRAKE .............................. 5-64
AUTOMATIC DAY / NIGHT MIRROR - DESCRIPTION ....................... 8N-28
AUTOMATIC DAY / NIGHT MIRROR - OPERATION ......................... 8N-28
AUTOMATIC DAY / NIGHT MIRROR, DIAGNOSIS AND TESTING .............8N-28
AUTOMATIC TEMPERATURE CONTROL, DESCRIPTION ........................ 24-3
AUTOMATIC TEMPERATURE CONTROL, OPERATION .......................... 24-5AUTOMATIC TEMPERATURE CONTROL
SYSTEM, OPERATION ................24-114
AUTOMATIC TRANSAXLE - DESCRIPTION, 40TE ................... 21-2
AUTOMATIC TRANSAXLE - DESCRIPTION, 41TE .................21-147
AUTOMATIC TRANSAXLE - OPERATION, 40TE ............................... 21-4
AUTOMATIC TRANSAXLE - OPERATION, 41TE ............................. 21-149
AUTOMATIC TRANSAXLE, SPECIAL TOOLS - 41TE ...................... 21-213
AUTOMATIC/MANUAL TRANSAXLE FLUID - DESCRIPTION ........................0-4
AWD - INSTALLATION ..................2-45
AWD - INSTALLATION, REAR WHEEL SPEED SENSOR ....................... 5-92
AWD - INSTALLATION, SPRING ..........2-39
AWD - REMOVAL ..................... 2-44
AWD - REMOVAL, REAR WHEEL SPEED SENSOR ............................ 5-92
AWD - REMOVAL, SPRING ..............2-38
AWD, HEAVY DUTY, CARGO - INSTALLATION ........................ 2-36
AWD, HEAVY DUTY, CARGO - REMOVAL . . . 2-36
AWD POWER TRANSFER UNIT FLUID - DESCRIPTION .........................0-6
AWD REAR DRIVELINE MODULE FLUIDS - DESCRIPTION ........................0-6
B OR C-PILLAR - INSTALLATION, SEAT BELT HEIGHT ADJUSTER ..............8O-38
B OR C-PILLAR - REMOVAL, SEAT BELT HEIGHT ADJUSTER ................... 8O-38
BACK - INSTALLATION, BENCH SEAT ....23-147
BACK - INSTALLATION, FRONT SEAT ....23-111
BACK - QUAD BUCKET - INSTALLATION, BUCKET SEAT ...................... 23-141
BACK - QUAD BUCKET - REMOVAL, BUCKET SEAT ...................... 23-140
BACK - REMOVAL, BENCH SEAT ........23-147
BACK - REMOVAL, FRONT SEAT ........23-111
BACK ASSIST STRAP - INSTALLATION, FRONT SEAT ....................... 23-112
BACK ASSIST STRAP - REMOVAL, FRONT SEAT ....................... 23-112
BACK COVER - INSTALLATION, BENCH SEAT ............................. 23-148
BACK COVER - INSTALLATION, FRONT SEAT ............................. 23-116
BACK COVER - REMOVAL, BENCH SEAT . . 23-148
BACK COVER - REMOVAL, FRONT SEAT . . 23-113
BACK COVER/FOAM - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-133
BACK COVER/FOAM - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-133
BACK COVER/FOAM - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-156
BACK COVER/FOAM - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-155
BACK FRAME - SECOND ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-134
BACK FRAME - SECOND ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-134
BACK FRAME - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT . . 23-157
BACK FRAME - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT ......23-156
BACK HINGE - REMOVAL, BENCH SEAT . . 23-146
BACK HINGE COVERS - QUAD BUCKET, 50/50 SPLIT, BENCH - INSTALLATION,
SEAT ............................. 23-146
BACK HINGE COVERS - QUAD BUCKET, 50/50 SPLIT, BENCH - REMOVAL, SEAT . . 23-146
BACK PANEL - INSTALLATION, BENCH SEAT ............................. 23-144
BACK PANEL - INSTALLATION, FRONT SEAT ............................. 23-113
BACK PANEL - REMOVAL, BENCH SEAT . . 23-143
BACK PANEL - REMOVAL, FRONT SEAT . . 23-112
BACK PANEL - SECOND ROW -FOLD-IN-FLOOR - INSTALLATION,
SEAT ............................. 23-134
BACK PANEL - SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT .....23-134
BACK PANEL - THIRD ROW -FOLD-IN- FLOOR - INSTALLATION, SEAT .........23-158
BACK PANEL - THIRD ROW -FOLD-IN- FLOOR - REMOVAL, SEAT .............23-158
2 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

DEFOGGER RELAY - DESCRIPTION,REAR WINDOW ....................... 8G-3
DEFOGGER RELAY - INSTALLATION, REAR WINDOW ....................... 8G-4
DEFOGGER RELAY - OPERATION, REAR WINDOW ............................ 8G-3
DEFOGGER RELAY - REMOVAL, REAR WINDOW ............................ 8G-4
DEFOGGER SWITCH - DESCRIPTION, REAR WINDOW ....................... 8G-4
DEFOGGER SWITCH - OPERATION, REAR WINDOW ............................ 8G-4
DEFROSTER DUCT - INSTALLATION ......24-50
DEFROSTER DUCT - REMOVAL ..........24-49
DEMAGNETIZING, STANDARD PROCEDURE - COMPASS ...............8M-5
DEMISTER DUCTS - INSTALLATION, INSTRUMENT PANEL .................. 24-54
DEMISTER DUCTS - REMOVAL, INSTRUMENT PANEL .................. 24-54
DEMISTER OUTLETS, INSTALLATION - FRONT ............................. 24-45
DEMISTER OUTLETS, REMOVAL - FRONT . 24-44
DEPLOYMENT - STANDARD PROCEDURE, SERVICE AFTER AN
AIRBAG ............................. 8O-7
DETECTION ASSY - INSTALLATION, NATURAL VAC LEAK .................. 25-14
DETECTION ASSY - REMOVAL, NATURAL VAC LEAK .......................... 25-14
DETECTION PUMP - INSTALLATION, LEAK .............................. 25-15
DETECTION PUMP - REMOVAL, LEAK ......25-15
DEVICES - STANDARD PROCEDURE, ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE ........................8W -01-8
DIAGNOSTIC SYSTEM, DIAGNOSIS AND TESTING - ON-BOARD .................8F-22
DIAGNOSTIC TROUBLE CODES - STANDARD PROCEDURE, OBTAINING .....8E-15
DIAGRAMS - 4XTE TRANSAXLE HYDRAULIC SCHEMATICS,
SCHEMATICS .................. 21-199,21-54
DIAGRAMS - DESCRIPTION, HOW TO USE WIRING ......................8W -01-1
DIAGRAMS - SPECIAL TOOLS, SCHEMATICS ........................ 21-68
DIESEL - DESCRIPTION ...............19-52
DIESEL - INSTALLATION ...............19-53
DIESEL - REMOVAL ................... 19-52
DIESEL ENGINE - DESCRIPTION, FUEL REQUIREMENTS .......................0-6
DIESEL ENGINES - DESCRIPTION, ENGINE OIL ...........................0-6
DIESEL ENGINES - EXPORT - DESCRIPTION ........................ 0-21
DIESEL ENGINES, INSTALLATION - 2.5L/2.8L ........................... 24-78
DIESEL ENGINES, REMOVAL - 2.5L/2.8L . . 24-77
DIFFERENTIAL BEARING PRELOAD - ADJUSTMENT ...................... 21-228
DIFFERENTIAL BEARING PRELOAD MEASUREMENT AND ADJUSTMENT,
ADJUSTMENTS ...................... 21-79
DIMENSIONS - FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS, FRAME ........13-11
DIMENSIONS - SPECIFICATIONS, BODY OPENING .......................... 23-180
DIMENSIONS - SPECIFICATIONS, FRAME . . . 13-6
DIODE - INSTALLATION ............8W-01-14
DIODE - REMOVAL ................8W -01-14
DISABLED INDICATOR - DESCRIPTION, PASSENGER AIRBAG .................8O-33
DISABLED INDICATOR - INSTALLATION, PASSENGER AIRBAG .................8O-34
DISABLED INDICATOR - OPERATION, PASSENGER AIRBAG .................8O-33
DISABLED INDICATOR - REMOVAL, PASSENGER AIRBAG .................8O-34
DISASSEMBLY/ASSEMBLY - STANDARD PROCEDURE, TRANSMISSION COOLER
LINE QUICK CONNECT FITTING ...........7-38
DISC BRAKE CALIPER - INSTALLATION, REAR ............................... 5-30
DISC BRAKE CALIPER - REMOVAL, REAR ............................... 5-28
DISC BRAKE CALIPER ADAPTER - INSTALLATION, FRONT .................5-31DISC BRAKE CALIPER ADAPTER -
REMOVAL, FRONT ..................... 5-31
DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) - INSTALLATION,
FRONT .............................. 5-27
DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT ......5-24
DISC BRAKE CALIPER GUIDE PINS (TRW BRAKES) - INSTALLATION ...............5-32
DISC BRAKE CALIPER GUIDE PINS (TRW BRAKES) - REMOVAL .................. 5-31
DISC BRAKE CALIPER (TRW BRAKES) - INSTALLATION, FRONT .................5-27
DISC BRAKE CALIPER (TRW BRAKES) - REMOVAL, FRONT ..................... 5-24
DISC BRAKE SHOES - CLEANING .....5-16,5-18
DISC BRAKE SHOES - INSPECTION . . . 5-16,5-18
DISC BRAKE SHOES - INSTALLATION, REAR ............................... 5-19
DISC BRAKE SHOES - REMOVAL, REAR ....5-17
DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) - INSTALLATION,
FRONT .............................. 5-16
DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) - REMOVAL, FRONT ......5-15
DISC BRAKE SHOES (TRW BRAKES) - INSTALLATION, FRONT .................5-17
DISC BRAKE SHOES (TRW BRAKES) - REMOVAL, FRONT ..................... 5-15
DISC BRAKES (EXPORT) - DESCRIPTION . . . 5-13
DISC BRAKES (FRONT) - DESCRIPTION ....5-11
DISC BRAKES (FRONT) - OPERATION ......5-13
DISC BRAKES (REAR) - DESCRIPTION .....5-13
DISC BRAKES (REAR) - OPERATION ......5-14
DISCHARGE (ESD) SENSITIVE DEVICES - STANDARD PROCEDURE,
ELECTROSTATIC ...................8W -01-8
DISCHARGE LINE - INSTALLATION, A/C . . . 24-80
DISCHARGE LINE - REMOVAL, A/C .......24-79
DISPLAY - DESCRIPTION, PARK ASSIST . . . 8B-3
DISPLAY - INSTALLATION, PARK ASSIST . . . 8B-4
DISPLAY - OPERATION, PARK ASSIST .....8B-3
DISPLAY - REMOVAL, PARK ASSIST ......8B-4
DISPLAY TEST MODE, OPERATION - DRB III T STATE .......................... 25-10
DISSASEMBLY, REMOVAL ..............24-51
DISTRIBUTION DUCT - INSTALLATION ....24-57
DISTRIBUTION DUCT - REMOVAL ........24-57
DISTRIBUTION DUCTS - INSTALLATION, FLOOR ............................. 24-50
DISTRIBUTION DUCTS - REMOVAL, FLOOR ............................. 24-50
DISTRIBUTION SYSTEM - DESCRIPTION, POWER ..........................8W -97-1
DISTRIBUTION SYSTEM - OPERATION, POWER ..........................8W -97-1
DISTRIBUTION SYSTEMS, SPECIAL TOOLS - POWER ...................8W -97-1
DOES NOT FILL - DIAGNOSIS AND TESTING, VEHICLE ................... 25-17
DOME/CARGO LAMP - INSTALLATION ....8L-22
DOME/CARGO LAMP - REMOVAL ........8L-22
DOOR - INSTALLATION ................23-15
DOOR - INSTALLATION, FUEL FILL .......23-52
DOOR - INSTALLATION, SLIDING ........23-29
DOOR - REMOVAL .................... 23-15
DOOR - REMOVAL, FUEL FILL ..........23-52
DOOR - REMOVAL, SLIDING ............23-29
DOOR ACTUATOR - DESCRIPTION, BLEND ........................ 24-22,24-34
DOOR ACTUATOR - DESCRIPTION, MODE ............................. 24-29
DOOR ACTUATOR - DESCRIPTION, RECIRCULATION ..................... 24-31
DOOR ACTUATOR - INSTALLATION, BLEND ........................ 24-22,24-35
DOOR ACTUATOR - INSTALLATION, MODE ............................. 24-30
DOOR ACTUATOR - INSTALLATION, RECIRCULATION ..................... 24-32
DOOR ACTUATOR - OPERATION, BLEND . . 24-22,
24-35
DOOR ACTUATOR - OPERATION, MODE . . . 24-29
DOOR ACTUATOR - OPERATION, RECIRCULATION ..................... 24-31
DOOR ACTUATOR - REAR - DESCRIPTION, MODE .................24-39DOOR ACTUATOR - REAR -
INSTALLATION, MODE .................24-40
DOOR ACTUATOR - REAR - OPERATION, MODE ............................. 24-39
DOOR ACTUATOR - REAR - REMOVAL, MODE ............................. 24-39
DOOR ACTUATOR - REMOVAL, BLEND . . . 24-22, 24-35
DOOR ACTUATOR - REMOVAL, MODE ....24-29
DOOR ACTUATOR - REMOVAL, RECIRCULATION ..................... 24-32
DOOR ADJUSTMENT, STANDARD PROCEDURE - POWER SLIDING .........8N-49
DOOR ADJUSTMENTS, ADJUSTMENTS - SLIDING ............................ 23-30
DOOR BLOCKER LATCH - INSTALLATION, FUEL FILL .......................... 23-53
DOOR BLOCKER LATCH - REMOVAL, FUEL FILL .......................... 23-53
DOOR BLOCKER LATCH STRIKER - INSTALLATION, FUEL FILL .............23-53
DOOR BLOCKER LATCH STRIKER - REMOVAL, FUEL FILL .................23-53
DOOR BLOCKER LOCKOUT LINK - INSTALLATION, FUEL FILL .............23-54
DOOR BLOCKER LOCKOUT LINK - REMOVAL, FUEL FILL .................23-54
DOOR CONTROL MODULE - DESCRIPTION, SLIDING ...............8E-18
DOOR CONTROL MODULE - OPERATION, SLIDING ............................ 8E-18
DOOR CONTROL MODULE, DIAGNOSIS AND TESTING - SLIDING ...............8E-18
DOOR CYLINDER LOCK SWITCH - EXPORT - DESCRIPTION ...............8N-22
DOOR CYLINDER LOCK SWITCH - EXPORT - OPERATION ................8N-22
DOOR CYLINDER LOCK SWITCH, EXPORT ............................ 8N-22
DOOR GLASS - INSTALLATION ..........23-17
DOOR GLASS - INSTALLATION, SLIDING . 23-163
DOOR GLASS - REMOVAL .............23-16
DOOR GLASS - REMOVAL, SLIDING .....23-163
DOOR GLASS RUN WEATHERSTRIP - INSTALLATION, FRONT ...............23-166
DOOR GLASS RUN WEATHERSTRIP - REMOVAL, FRONT ................... 23-166
DOOR INNER BELT MOLDING - INSTALLATION, FRONT ...............23-168
DOOR INNER BELT MOLDING - REMOVAL, FRONT ................... 23-168
DOOR LEARN CYCLE, STANDARD PROCEDURE - POWER SLIDING .........8N-48
DOOR LOCK MOTOR - INSTALLATION, SLIDING ........................... 8N-25
DOOR LOCK MOTOR - REMOVAL, SLIDING ........................... 8N-25
DOOR LOCK MOTOR, DIAGNOSIS AND TESTING ........................... 8N-23
DOOR LOCK SWITCH, DIAGNOSIS AND TESTING ........................... 8N-23
DOOR MOTOR - DESCRIPTION, SLIDING . . 8N-51
DOOR MOTOR - INSTALLATION, SLIDING . 8N-51
DOOR MOTOR - OPERATION, SLIDING . . . 8N-51
DOOR MOTOR - REMOVAL, SLIDING .....8N-51
DOOR OUTER BELT MOLDING - INSTALLATION, FRONT ...............23-167
DOOR OUTER BELT MOLDING - REMOVAL, FRONT ................... 23-167
DOOR SILL PLATE - INSTALLATION, SLIDING ............................ 23-99
DOOR SILL PLATE - REMOVAL, SLIDING . . 23-98
DOOR SILL TRIM PLATE - INSTALLATION ....................... 23-89
DOOR SILL TRIM PLATE - REMOVAL .....23-89
DOOR STOP BUMPER BEZEL - INSTALLATION, SLIDING ...............23-25
DOOR STOP BUMPER BEZEL - REMOVAL, SLIDING .................. 23-25
DOOR SYSTEM - DESCRIPTION, POWER SLIDING ........................... 8N-40
DOOR SYSTEM - OPERATION, POWER SLIDING ........................... 8N-41
DOOR SYSTEM, DIAGNOSIS AND TESTING - POWER SLIDING ............8N-42
DOOR WEATHERSTRIP - INSTALLATION, FRONT ............................ 23-168
10 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

FILTER ADAPTER - INSTALLATION, OIL . . . 9-142
FILTER ADAPTER - REMOVAL, OIL.......9-142
FILTER CHANGE - STANDARD PROCEDURE, ENGINE OIL ..........9-139,9-54
FILTER SERVICE - STANDARD PROCEDURE, FLUID ............21-231,21-82
FINAL DRIVE - ASSEMBLY .......21-224,21-78
FINAL DRIVE - DESCRIPTION .....21-219,21-74
FINAL DRIVE - DISASSEMBLY ....21-220,21-75
FINAL DRIVE - OPERATION .......21-220,21-75
FINESSE SANDING/BUFFING & POLISHING - DESCRIPTION ...........23-101
FINISH - DESCRIPTION, BASE COAT/CLEARCOAT ................... 23-101
FIRING ORDER, SPECIFICATIONS .........8I-3
FIRST ROW - BENCH - INSTALLATION, SEAT BELT BUCKLE .................. 8O-37
FIRST ROW - BENCH - REMOVAL, SEAT BELT BUCKLE ....................... 8O-36
FIRST ROW - OUTBOARD - INSTALLATION, SEAT BELT &
RETRACTOR ........................ 8O-40
FIRST ROW - OUTBOARD - REMOVAL, SEAT BELT & RETRACTOR .............8O-39
FIRST ROW INBOARD - QUAD BUCKET - INSTALLATION, SEAT BELT BUCKLE ......8O-36
FIRST ROW INBOARD - QUAD BUCKET - REMOVAL, SEAT BELT BUCKLE .........8O-35
FITTING - CONNECTING ROD ............9-46
FITTING - PISTON RING ................9-47
FITTING - STANDARD PROCEDURE, MAIN BEARING ...................... 9-125
FITTING - STANDARD PROCEDURE, PISTON RING ....................... 9-124
FITTING - STANDARD PROCEDURE, PISTON TO CYLINDER BORE ............9-44
FITTING CONNECTING RODS - STANDARD PROCEDURE ...............9-119
FITTING DISASSEMBLY/ASSEMBLY - STANDARD PROCEDURE,
TRANSMISSION COOLER LINE QUICK
CONNECT ............................ 7-38
FITTING PISTONS - STANDARD PROCEDURE ........................ 9-120
FITTINGS - STANDARD PROCEDURE, QUICK-CONNECT ..................... 14-18
FITTINGS, STANDARD PROCEDURE - HANDLING TUBING ................... 24-69
FLAP AND SPRING ASSEMBLY - INSTALLATION, QUAD BUCKET SEAT
SIDE SHIELD/CUP HOLDER ............23-151
FLAP AND SPRING ASSEMBLY - REMOVAL, QUAD BUCKET SEAT SIDE
SHIELD/CUP HOLDER ................23-151
FLEX DRIVE - DESCRIPTION ...........8N-55
FLEX DRIVE - INSTALLATION ...........8N-56
FLEX DRIVE - OPERATION .............8N-55
FLEX DRIVE - REMOVAL ...............8N-55
FLEX PLATE - INSTALLATION ...........9-133
FLEX PLATE - REMOVAL ...............9-133
FLEXIBLE FUEL ENGINE OIL - DESCRIPTION .........................0-3
FLOOR CONSOLE - FOLD-IN-FLOOR - INSTALLATION ....................... 23-89
FLOOR CONSOLE - FOLD-IN-FLOOR - REMOVAL .......................... 23-89
FLOOR CONSOLE BASE TRAY - INSTALLATION ....................... 23-89
FLOOR CONSOLE BASE TRAY - REMOVAL .......................... 23-89
FLOOR CONSOLE KEY LOCK TUMBLER - FOLD-IN-FLOOR - INSTALLATION ........23-90
FLOOR CONSOLE KEY LOCK TUMBLER - FOLD-IN-FLOOR - REMOVAL ............23-90
FLOOR CONSOLE LID LATCH - FOLD-IN-FLOOR - INSTALLATION ........23-90
FLOOR CONSOLE LID LATCH - FOLD-IN-FLOOR - REMOVAL ............23-90
FLOOR DISTRIBUTION DUCTS - INSTALLATION ....................... 24-50
FLOOR DISTRIBUTION DUCTS - REMOVAL .......................... 24-50
FLOOR HEAT DUCT - INSTALLATION, REAR .............................. 24-63
FLOOR HEAT DUCT - REMOVAL, REAR . . . 24-63
FLOOR MATS - INSTALLATION, CARPETS . 23-81
FLOOR MATS - REMOVAL, CARPETS .....23-81 FLOOR TUB CARPET INSERT -
FOLD-IN-FLOOR - INSTALLATION,
SECOND ROW ....................... 23-98
FLOOR TUB CARPET INSERT - FOLD-IN-FLOOR - REMOVAL, SECOND
ROW .............................. 23-98
FLOOR TUB CARPETS INSERT - FOLD-IN-FLOOR - INSTALLATION,
REAR .............................. 23-96
FLOOR TUB CARPETS INSERT - FOLD-IN-FLOOR - REMOVAL, REAR ......23-95
FLOW AND PRESSURE TEST - DIAGNOSIS AND TESTING, POWER
STEERING SYSTEM .................... 19-1
FLOW CHECK - DIAGNOSIS AND TESTING, COOLING SYSTEM .............7-3
FLUID - DESCRIPTION, AUTOMATIC/ MANUAL TRANSAXLE ...................0-4
FLUID - DESCRIPTION, AWD POWER TRANSFER UNIT .......................0-6
FLUID AND FILTER SERVICE - STANDARD PROCEDURE .........21-231,21-82
FLUID CAPACITIES - SPECIFICATIONS ......0-6
FLUID CONTAMINATION - DIAGNOSIS AND TESTING, BRAKE .................. 5-33
FLUID COOLER - DESCRIPTION .........19-45
FLUID COOLER - INSTALLATION .........19-45
FLUID COOLER - OPERATION ...........19-45
FLUID COOLER - REMOVAL ............19-45
FLUID FILL/CHECK LOCATIONS - DESCRIPTION .........................0-7
FLUID LEAKAGE - DIAGNOSIS AND TESTING, TORQUE CONVERTER
HOUSING ....................... 21-154,21-9
FLUID LEVEL AND CONDITION CHECK, STANDARD PROCEDURE .........21-230,21-82
FLUID LEVEL CHECKING - STANDARD PROCEDURE, BRAKE ................... 5-33
FLUID LEVEL CHECKING - STANDARD PROCEDURE, POWER STEERING ........19-44
FLUID LEVEL SWITCH - DESCRIPTION, BRAKE .............................. 5-10
FLUID LEVEL SWITCH - INSTALLATION, BRAKE .............................. 5-11
FLUID LEVEL SWITCH - INSTALLATION, WASHER ........................... 8R-11
FLUID LEVEL SWITCH - OPERATION, BRAKE .............................. 5-10
FLUID LEVEL SWITCH - REMOVAL, BRAKE .............................. 5-11
FLUID LEVEL SWITCH - REMOVAL, WASHER ........................... 8R-11
FLUID, SPECIFICATIONS - BRAKE .........5-33
FLUIDS - DESCRIPTION, AWD REAR DRIVELINE MODULE ....................0-6
FLUSH MEASUREMENTS - SPECIFICATIONS, GAP ................23-177
FOG LAMP - DIAGNOSIS AND TESTING, FRONT .............................. 8L-7
FOG LAMP - INSTALLATION, FRONT .......8L-8
FOG LAMP - REMOVAL, FRONT ..........8L-8
FOG LAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE, FRONT ........8L-9
FOG LAMP UNIT ALIGNMENT - STANDARD PROCEDURE, FRONT .........8L-9
FOLDAWAY MIRROR SWITCH - EXPORT - DESCRIPTION, POWER ..............8N-29
FOLDAWAY MIRROR SWITCH - EXPORT - INSTALLATION, POWER ..............8N-30
FOLDAWAY MIRROR SWITCH - EXPORT - OPERATION, POWER ................8N-29
FOLDAWAY MIRROR SWITCH - EXPORT - REMOVAL, POWER .................. 8N-29
FOLD-IN-FLOOR - INSTALLATION . . . 14-10,14-16
FOLD-IN-FLOOR - INSTALLATION, ARMREST - SECOND ROW ............23-130
FOLD-IN-FLOOR - INSTALLATION, ARMREST ROTATING ASSEMBLY -
SECOND ROW ...................... 23-130
FOLD-IN-FLOOR - INSTALLATION, BOTTOM OF SEAT CUSHION PAN
PANEL-THIRD ROW .................. 23-152
FOLD-IN-FLOOR - INSTALLATION, CARPET TRIM RING AND COVER ........23-84
FOLD-IN-FLOOR - INSTALLATION, CARPETS ........................... 23-83
FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE ........................... 23-89FOLD-IN-FLOOR - INSTALLATION, FLOOR
CONSOLE KEY LOCK TUMBLER .........23-90
FOLD-IN-FLOOR - INSTALLATION, FLOOR CONSOLE LID LATCH .................23-90
FOLD-IN-FLOOR - INSTALLATION, HEADREST SLEEVE - SECOND ROW .....23-131
FOLD-IN-FLOOR - INSTALLATION, HEADREST SLEEVE - THIRD ROW ......23-153
FOLD-IN-FLOOR - INSTALLATION, REAR FLOOR TUB CARPETS INSERT ..........23-96
FOLD-IN-FLOOR - INSTALLATION, SEAT - SECOND ROW ...................... 23-132
FOLD-IN-FLOOR - INSTALLATION, SEAT - THIRD ROW ........................ 23-154
FOLD-IN-FLOOR - INSTALLATION, SEAT BACK COVER/FOAM - SECOND ROW ....23-133
FOLD-IN-FLOOR - INSTALLATION, SEAT BACK COVER/FOAM - THIRD ROW ......23-156
FOLD-IN-FLOOR - INSTALLATION, SEAT BACK FRAME - SECOND ROW .........23-134
FOLD-IN-FLOOR - INSTALLATION, SEAT BACK FRAME - THIRD ROW ...........23-157
FOLD-IN-FLOOR - INSTALLATION, SEAT BACKSTOW STRAP - THIRD ROW ......23-158
FOLD-IN-FLOOR - INSTALLATION, SEAT BASE RISER - SECOND ROW ..........23-135
FOLD-IN-FLOOR - INSTALLATION, SEAT BELT CENTER LAP BELT ..............23-157
FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION COVER/FOAM - THIRD ROW . . . 23-159
FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION COVER/FOAM -SECOND
ROW ............................. 23-136
FOLD-IN-FLOOR - INSTALLATION, SEAT CUSHION SIDE SHIELD - SECOND
ROW ............................. 23-138
FOLD-IN-FLOOR - INSTALLATION, SEAT GAS STRUT - SECOND ROW ...........23-139
FOLD-IN-FLOOR - INSTALLATION, SEAT PROP ROD - SECOND ROW ...........23-140
FOLD-IN-FLOOR - INSTALLATION, SECOND ROW FLOOR TUB CARPET
INSERT ............................ 23-98
FOLD-IN-FLOOR - INSTALLATION, SIDE SHIELD CUP HOLDER ................23-160
FOLD-IN-FLOOR - INSTALLATION, WITH NVLD .............................. 25-20
FOLD-IN-FLOOR - REMOVAL .......14-10,14-13
FOLD-IN-FLOOR - REMOVAL, ARMREST - SECOND ROW ..................... 23-130
FOLD-IN-FLOOR - REMOVAL, ARMREST ROTATING ASSEMBLY - SECOND ROW . . 23-130
FOLD-IN-FLOOR - REMOVAL, BOTTOM OF SEAT CUSHION PAN PANEL-THIRD
ROW ............................. 23-152
FOLD-IN-FLOOR - REMOVAL, CARPET TRIM RING AND COVER ...............23-84
FOLD-IN-FLOOR - REMOVAL, CARPETS . . . 23-82
FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE ........................... 23-89
FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE KEY LOCK TUMBLER .........23-90
FOLD-IN-FLOOR - REMOVAL, FLOOR CONSOLE LID LATCH .................23-90
FOLD-IN-FLOOR - REMOVAL, HEADREST SLEEVE - SECOND ROW ..............23-131
FOLD-IN-FLOOR - REMOVAL, HEADREST SLEEVE - THIRD ROW ...............23-152
FOLD-IN-FLOOR - REMOVAL, REAR FLOOR TUB CARPETS INSERT ..........23-95
FOLD-IN-FLOOR - REMOVAL, SEAT - SECOND ROW ...................... 23-132
FOLD-IN-FLOOR - REMOVAL, SEAT - THIRD ROW ........................ 23-153
FOLD-IN-FLOOR - REMOVAL, SEAT BACK COVER/FOAM - SECOND ROW .........23-133
FOLD-IN-FLOOR - REMOVAL, SEAT BACK COVER/FOAM - THIRD ROW ...........23-155
FOLD-IN-FLOOR - REMOVAL, SEAT BACK FRAME - SECOND ROW ..............23-134
FOLD-IN-FLOOR - REMOVAL, SEAT BACK FRAME - THIRD ROW ................23-156
FOLD-IN-FLOOR - REMOVAL, SEAT BACKSTOW STRAP - THIRD ROW ......23-158
FOLD-IN-FLOOR - REMOVAL, SEAT BASE RISER - SECOND ROW ...............23-134
FOLD-IN-FLOOR - REMOVAL, SEAT BELT CENTER LAP BELT ................... 23-157
RS INDEX13
Description Group-Page Description Group-Page Description Group-Page

FOLD-IN-FLOOR - REMOVAL, SEATCUSHION COVER/FOAM - THIRD ROW . . . 23-159
FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION COVER/FOAM -SECOND
ROW ............................. 23-136
FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION SIDE SHIELD - SECOND
ROW ............................. 23-138
FOLD-IN-FLOOR - REMOVAL, SEAT GAS STRUT - SECOND ROW ...............23-138
FOLD-IN-FLOOR - REMOVAL, SEAT PROP ROD - SECOND ROW ................23-139
FOLD-IN-FLOOR - REMOVAL, SECOND ROW FLOOR TUB CARPET INSERT .......23-98
FOLD-IN-FLOOR - REMOVAL, SIDE SHIELD CUP HOLDER ................23-160
FOLD-IN-FLOOR - REMOVAL, WITH NVLD .............................. 25-20
FOLD-IN-FLOOR - SPECIFICATIONS, WELD LOCATIONS ................... 23-350
FOLD-IN-FLOOR ONLY - SPECIFICATIONS, BODY SEALING
LOCATIONS ........................ 23-209
FOLD-IN-FLOOR ONLY - SPECIFICATIONS, STRUCTURAL
ADHESIVE LOCATIONS ...............23-228
FOLD-IN-FLOOR SEATING - INSTALLATION .................... 5-68,5-75
FOLD-IN-FLOOR SEATING - INSTALLATION, FWD ................... 2-45
FOLD-IN-FLOOR SEATING - REMOVAL . 5-66,5-72
FOLD-IN-FLOOR SEATING - REMOVAL, FWD................................ 2-45
FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS, FRAME DIMENSIONS .....13-11
FOLDING MECHANISM -SECOND ROW -FOLD-IN-FLOOR - INSTALLATION,
SEAT RECLINER/FORWARD ............23-137
FOLDING MECHANISM -SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT
RECLINER/FORWARD ................23-137
FORM-IN-PLACE GASKETS AND SEALERS, STANDARD PROCEDURE . . . 9-11,9-86
FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR - INSTALLATION,
SEAT RECLINER/FOLD ................23-160
FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR - REMOVAL, SEAT
RECLINER/FOLD .................... 23-160
FRAME - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT BACK ....23-134
FRAME - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT BACK ........23-134
FRAME - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK ..........23-157
FRAME - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK ..............23-156
FRAME DIMENSIONS - FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS .........13-11
FRAME DIMENSIONS - SPECIFICATIONS . . . 13-6
FREE MODULE - INSTALLATION, HANDS . . . 8T-3
FREE MODULE - REMOVAL, HANDS .......8T-3
FRONT - DESCRIPTION, HALF SHAFT .......3-1
FRONT - DESCRIPTION, PLUMBING ......24-65
FRONT - INSTALLATION, BUSHING - LEAF SPRING ........................ 2-30
FRONT - INSTALLATION, CRANKSHAFT OIL SEAL ....................... 9-130,9-42
FRONT - INSTALLATION, HALF SHAFT ......3-4
FRONT - INSTALLATION, SEAT BELT & RETRACTOR - OUTBOARD .............8O-39
FRONT - INSTALLATION, SPRING MOUNTS ............................ 2-43
FRONT - INSTALLATION, WHEEL MOUNTING STUDS ................... 22-21
FRONT - OPERATION, PLUMBING ........24-65
FRONT - REMOVAL, BUSHING - LEAF SPRING ............................. 2-29
FRONT - REMOVAL, CRANKSHAFT OIL SEAL .......................... 9-130,9-41
FRONT - REMOVAL, HALF SHAFT ..........3-2
FRONT - REMOVAL, SEAT BELT & RETRACTOR - OUTBOARD .............8O-38
FRONT - REMOVAL, SPRING MOUNTS .....2-42
FRONT - REMOVAL, WHEEL MOUNTING STUDS ............................. 22-21
FRONT - SPECIFICATIONS, HALF SHAFT ....3-6FRONT A/C EXPANSION VALVE,
DIAGNOSIS AND TESTING .............24-82
FRONT BLOWER MOTOR, DIAGNOSIS AND TESTING ....................... 24-46
FRONT BLOWER MOTOR RESISTOR BLOCK, DIAGNOSIS AND TESTING .......24-25
FRONT BRAKE ROTOR - INSTALLATION ....5-59
FRONT BRAKE ROTOR - REMOVAL .......5-59
FRONT BUMPER REINFORCEMENT - INSTALLATION ........................ 13-3
FRONT BUMPER REINFORCEMENT - REMOVAL ........................... 13-3
FRONT CABLE - INSTALLATION, PARKING BRAKE LEVER ................5-77
FRONT CABLE - REMOVAL, PARKING BRAKE LEVER ........................ 5-77
FRONT CENTER BEZEL OUTLETS, INSTALLATION ....................... 24-45
FRONT CENTER BEZEL OUTLETS, REMOVAL .......................... 24-44
FRONT CONTROL MODULE - DESCRIPTION ........................ 8E-7
FRONT CONTROL MODULE - OPERATION . . 8E-7
FRONT CONTROL MODULE, DIAGNOSIS AND TESTING ........................ 8E-7
FRONT CRADLE CROSSMEMBER - DESCRIPTION ....................... 13-14
FRONT CRADLE CROSSMEMBER THREAD REPAIR - DESCRIPTION ........13-14
FRONT CROSSMEMBER MOUNT BUSHINGS - INSTALLATION ............13-17
FRONT CROSSMEMBER MOUNT BUSHINGS - REMOVAL .................13-17
FRONT DEMISTER OUTLETS, INSTALLATION ....................... 24-45
FRONT DEMISTER OUTLETS, REMOVAL . . . 24-44
FRONT DISC BRAKE CALIPER ADAPTER - INSTALLATION ...................... 5-31
FRONT DISC BRAKE CALIPER ADAPTER - REMOVAL .......................... 5-31
FRONT DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) -
INSTALLATION ........................ 5-27
FRONT DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) -
REMOVAL ........................... 5-24
FRONT DISC BRAKE CALIPER (TRW BRAKES) - INSTALLATION ...............5-27
FRONT DISC BRAKE CALIPER (TRW BRAKES) - REMOVAL .................. 5-24
FRONT DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) -
INSTALLATION ........................ 5-16
FRONT DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) -
REMOVAL ........................... 5-15
FRONT DISC BRAKE SHOES (TRW BRAKES) - INSTALLATION ...............5-17
FRONT DISC BRAKE SHOES (TRW BRAKES) - REMOVAL .................. 5-15
FRONT DOOR GLASS RUN WEATHERSTRIP - INSTALLATION .......23-166
FRONT DOOR GLASS RUN WEATHERSTRIP - REMOVAL ...........23-166
FRONT DOOR INNER BELT MOLDING - INSTALLATION ...................... 23-168
FRONT DOOR INNER BELT MOLDING - REMOVAL ......................... 23-168
FRONT DOOR OUTER BELT MOLDING - INSTALLATION ...................... 23-167
FRONT DOOR OUTER BELT MOLDING - REMOVAL ......................... 23-167
FRONT DOOR WEATHERSTRIP - INSTALLATION ...................... 23-168
FRONT DOOR WEATHERSTRIP - REMOVAL ......................... 23-168
FRONT FASCIA - INSTALLATION ..........13-1
FRONT FASCIA - REMOVAL ..............13-1
FRONT FENDER - INSTALLATION ........23-52
FRONT FENDER - REMOVAL ............23-51
FRONT FOG LAMP - DIAGNOSIS AND TESTING ............................ 8L-7
FRONT FOG LAMP - INSTALLATION .......8L-8
FRONT FOG LAMP - REMOVAL ...........8L-8
FRONT FOG LAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE .......8L-9
FRONT FOG LAMP UNIT ALIGNMENT - STANDARD PROCEDURE ................8L-9FRONT HEATER CORE, INSTALLATION
....24-86
FRONT HEATER CORE, REMOVAL ........24-85
FRONT HEATER CORE TUBES, INSTALLATION ....................... 24-85
FRONT HEATER CORE TUBES, REMOVAL . . 24-84
FRONT INBOARD - INSTALLATION, SEAT BELT BUCKLE ....................... 8O-35
FRONT INBOARD - REMOVAL, SEAT BELT BUCKLE ....................... 8O-35
FRONT MOUNT - INSTALLATION ....9-134,9-50
FRONT MOUNT - REMOVAL ........9-134,9-50
FRONT SEAT - INSTALLATION ..........23-110
FRONT SEAT - REMOVAL .............23-108
FRONT SEAT BACK - INSTALLATION .....23-111
FRONT SEAT BACK - REMOVAL ........23-111
FRONT SEAT BACK ASSIST STRAP - INSTALLATION ...................... 23-112
FRONT SEAT BACK ASSIST STRAP - REMOVAL ......................... 23-112
FRONT SEAT BACK COVER - INSTALLATION ...................... 23-116
FRONT SEAT BACK COVER - REMOVAL . . 23-113
FRONT SEAT BACK PANEL - INSTALLATION ...................... 23-113
FRONT SEAT BACK PANEL - REMOVAL . . 23-112
FRONT SEAT CUSHION - INSTALLATION . . 23-118
FRONT SEAT CUSHION - OCS - INSTALLATION ...................... 23-120
FRONT SEAT CUSHION - OCS - REMOVAL ........................... 23-119
FRONT SEAT CUSHION - REMOVAL .....23-117
FRONT SEAT CUSHION SIDE COVER - INSTALLATION ...................... 23-121
FRONT SEAT CUSHION SIDE COVER - OCS - INSTALLATION ................23-122
FRONT SEAT CUSHION SIDE COVER - OCS - REMOVAL .................... 23-121
FRONT SEAT CUSHION SIDE COVER - REMOVAL ......................... 23-120
FRONT SEAT RISER - MANUAL - OCS - INSTALLATION ...................... 23-123
FRONT SEAT RISER - MANUAL - OCS - REMOVAL ......................... 23-123
FRONT SEAT TRACK - REAR COVER - INSTALLATION ...................... 23-128
FRONT SEAT TRACK - REAR COVER - REMOVAL ......................... 23-128
FRONT SEAT TRACK ADJUSTER/MANUAL - OCS - INSTALLATION ...............23-128
FRONT SEAT TRACK ADJUSTER/MANUAL - OCS - REMOVAL ................... 23-126
FRONT SEAT TRACK ADJUSTER/POWER - OCS - INSTALLATION ...............23-125
FRONT SEAT TRACK ADJUSTER/POWER - OCS - REMOVAL ................... 23-124
FRONT SEAT TRACK MANUAL ADJUSTER - INSTALLATION ...........23-126
FRONT SEAT TRACK MANUAL ADJUSTER - REMOVAL ...............23-125
FRONT SEAT TRACK POWER ADJUSTER - INSTALLATION .................... 23-124
FRONT SEAT TRACK POWER ADJUSTER - REMOVAL ........................ 23-124
FRONT SEAT TRACK REAR COVER - OCS - INSTALLATION .................... 23-129
FRONT SEAT TRACK REAR COVER - OCS - REMOVAL ........................ 23-129
FRONT SUSPENSION - DESCRIPTION ......2-2
FRONT SUSPENSION - OPERATION ........2-2
FRONT SUSPENSION FASTENER TORQUE, SPECIFICATIONS ...............2-3
FRONT SUSPENSION, SPECIAL TOOLS .....2-3
FRONT WHEEL SPEED SENSOR - INSTALLATION ........................ 5-92
FRONT WHEEL SPEED SENSOR - REMOVAL ........................... 5-91
FRONT WHEELHOUSE SPLASH SHIELD - INSTALLATION ....................... 23-57
FRONT WHEELHOUSE SPLASH SHIELD - REMOVAL .......................... 23-57
FRONT WIPER ARM ALIGNMENT - STANDARD PROCEDURE ...............8R-9
FRONT WIPER ARMS - INSTALLATION ....8R-9
FRONT WIPER ARMS - REMOVAL ........8R-9
FRONT WIPER MOTOR - INSTALLATION . . 8R-10
FRONT WIPER MOTOR - REMOVAL .......8R-9
FRONT WIPER SYSTEM - DIAGNOSIS AND TESTING ........................ 8R-2
14 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

OCS - REMOVAL, FRONT SEAT CUSHION . 23-119
OCS - REMOVAL, FRONT SEAT CUSHIONSIDE COVER ....................... 23-121
OCS - REMOVAL, FRONT SEAT RISER - MANUAL .......................... 23-123
OCS - REMOVAL, FRONT SEAT TRACK ADJUSTER/MANUAL .................23-126
OCS - REMOVAL, FRONT SEAT TRACK ADJUSTER/POWER .................. 23-124
OCS - REMOVAL, FRONT SEAT TRACK REAR COVER ....................... 23-129
OIL - DESCRIPTION, FLEXIBLE FUEL ENGINE ..............................0-3
OIL - DESCRIPTION, REFRIGERANT ......24-94
OIL - DIESEL ENGINES - DESCRIPTION, ENGINE ..............................0-6
OIL - OPERATION, REFRIGERANT ........24-94
OIL AND FILTER CHANGE - STANDARD PROCEDURE, ENGINE .............9-139,9-54
OIL AND LUBRICANTS - DESCRIPTION, ENGINE ..............................0-1
OIL COOLER - DESCRIPTION, TRANSMISSION ....................... 7-39
OIL COOLER - INSPECTION, TRANSMISSION ....................... 7-39
OIL COOLER & LINES - DESCRIPTION ....9-141
OIL COOLER & LINES - INSTALLATION . . . 9-141
OIL COOLER & LINES - OPERATION ......9-141
OIL COOLER & LINES - REMOVAL .......9-141
OIL COOLER LINES - INSTALLATION, TRANSMISSION ....................... 7-40
OIL COOLER LINES - REMOVAL, TRANSMISSION ....................... 7-39
OIL FILTER - DESCRIPTION .............9-54
OIL FILTER - INSTALLATION ........9-141,9-54
OIL FILTER - REMOVAL ............9-141,9-54
OIL FILTER ADAPTER - INSTALLATION ....9-142
OIL FILTER ADAPTER - REMOVAL .......9-142
OIL GALLERY PLUGS - STANDARD PROCEDURE, ENGINE CORE .........9-10,9-88
OIL LEAK INSPECTION - DIAGNOSIS AND TESTING, ENGINE ..............9-8,9-84
OIL LEVEL CHECK - STANDARD PROCEDURE, ENGINE .................9-140
OIL LEVEL CHECK, STANDARD PROCEDURE - ENGINE .................9-54
OIL LEVEL, STANDARD PROCEDURE - REFRIGERANT ....................... 24-94
OIL PAN - CLEANING .................9-142
OIL PAN - INSPECTION ................9-143
OIL PAN - INSTALLATION ..........9-143,9-55
OIL PAN - REMOVAL ..............9-142,9-55
OIL PRESSURE - DIAGNOSIS AND TESTING, CHECKING ENGINE ............9-53
OIL PRESSURE - DIAGNOSIS AND TESTING, ENGINE .................... 9-138
OIL PRESSURE RELIEF VALVE - INSTALLATION ....................... 9-144
OIL PRESSURE RELIEF VALVE - REMOVAL .......................... 9-143
OIL PRESSURE SWITCH - DESCRIPTION . . 9-144
OIL PRESSURE SWITCH - INSTALLATION . 9-144, 9-56
OIL PRESSURE SWITCH - OPERATION ....9-144
OIL PRESSURE SWITCH - REMOVAL . 9-144,9-56
OIL PUMP - ASSEMBLY ...........9-146,9-58
OIL PUMP - ASSEMBLY ........21-112,21-263
OIL PUMP - CLEANING ............9-145,9-57
OIL PUMP - DESCRIPTION .............9-144
OIL PUMP - DESCRIPTION ......21-110,21-261
OIL PUMP - DISASSEMBLY ........9-145,9-57
OIL PUMP - DISASSEMBLY ......21-110,21-261
OIL PUMP - INSPECTION ..........9-145,9-58
OIL PUMP - INSTALLATION ........9-146,9-59
OIL PUMP - INSTALLATION, SEAL ......21-113,
21-264
OIL PUMP - OPERATION ........21-110,21-261
OIL PUMP - REMOVAL ............9-144,9-56
OIL PUMP - REMOVAL, SEAL ....21-113,21-264
OIL SEAL - FRONT - INSTALLATION, CRANKSHAFT ................... 9-130,9-42
OIL SEAL - FRONT - REMOVAL, CRANKSHAFT ................... 9-130,9-41
OIL SEAL - REAR - INSTALLATION, CRANKSHAFT ................... 9-131,9-42
OIL SEAL - REAR - REMOVAL, CRANKSHAFT ................... 9-131,9-42OIL SEAL RETAINER - INSTALLATION,
CRANKSHAFT REAR .................. 9-132
OIL SEAL RETAINER - REMOVAL, CRANKSHAFT REAR .................. 9-132
OIL SEAL(S) - INSTALLATION, CAMSHAFT .......................... 9-29
OIL SEAL(S) - REMOVAL, CAMSHAFT .....9-28
ON-BOARD DIAGNOSTIC SYSTEM, DIAGNOSIS AND TESTING ..............8F-22
ONLY - SPECIFICATIONS, BODY SEALING LOCATIONS - FOLD-IN-FLOOR .........23-209
ONLY - SPECIFICATIONS, FRAME DIMENSIONS - FOLD-IN-FLOOR SEATS . . . 13-11
ONLY - SPECIFICATIONS, STRUCTURAL ADHESIVE LOCATIONS - FOLD-IN-
FLOOR ............................ 23-228
OPEN LATCH - INSTALLATION, HOLD .....23-25
OPEN LATCH - REMOVAL, HOLD ........23-25
OPEN LATCH CABLE - INSTALLATION, HOLD .............................. 23-38
OPEN LATCH CABLE - REMOVAL, HOLD . . . 23-38
OPEN LATCH STRIKER - INSTALLATION, HOLD .............................. 23-26
OPEN LATCH STRIKER - REMOVAL, HOLD .............................. 23-26
OPEN SWITCH - DESCRIPTION, FULL ....8N-11,
8N-52
OPEN SWITCH - INSTALLATION, FULL ....8N-11
OPEN SWITCH - OPERATION, FULL . 8N-11,8N-52
OPEN SWITCH - REMOVAL, FULL .......8N-11
OPEN-CIRCUIT VOLTAGE TEST, STANDARD PROCEDURE ................8F-13
OPENING DIMENSIONS - SPECIFICATIONS, BODY ..............23-180
ORVR - OPERATION ..................25-15
OUTER BELT MOLDING - INSTALLATION, FRONT DOOR ...................... 23-167
OUTER BELT MOLDING - REMOVAL, FRONT DOOR ...................... 23-167
OUTER TIE ROD - INSTALLATION ........19-35
OUTER TIE ROD - REMOVAL ...........19-34
OUTLET - DESCRIPTION, POWER ......8W-97-3
OUTLET - DIAGNOSIS & TESTING, POWER ..........................8W -97-3
OUTLET - OPERATION, POWER .......8W-97-3
OUTLETS - DESCRIPTION, AIR .....24-43,24-56
OUTLETS - INSTALLATION, AIR .........24-56
OUTLETS - REMOVAL, AIR .............24-56
OUTLETS, INSTALLATION - FRONT CENTER BEZEL ...................... 24-45
OUTLETS, INSTALLATION - FRONT DEMISTER .......................... 24-45
OUTLETS, INSTALLATION - INSTRUMENT PANEL ............................. 24-45
OUTLETS, REMOVAL - FRONT CENTER BEZEL ............................. 24-44
OUTLETS, REMOVAL - FRONT DEMISTER . 24-44
OUTLETS, REMOVAL - INSTRUMENT PANEL ............................. 24-45
OUTPUT - DESCRIPTION, SPEED SENSOR ..................... 21-122,21-273
OUTPUT - INSTALLATION, SPEED SENSOR ..................... 21-123,21-274
OUTPUT - OPERATION, 5 VOLT SUPPLY - PCM............................... 8E-15
OUTPUT - OPERATION, SPEED SENSOR . 21-122, 21-273
OUTPUT - REMOVAL, SPEED SENSOR . . 21-123,
21-274
OUTSIDE HANDLE - INSTALLATION ......23-36
OUTSIDE HANDLE - REMOVAL ..........23-35
OUTSIDE HANDLE CABLE - INSTALLATION ....................... 23-37
OUTSIDE HANDLE CABLE - REMOVAL ....23-37
OVER STEERING COLUMN COVER - INSTALLATION ....................... 23-76
OVER STEERING COLUMN COVER - REMOVAL .......................... 23-76
OVERHEAD CONSOLE - DESCRIPTION ....8M-2
OVERHEAD CONSOLE, DIAGNOSIS AND TESTING ............................ 8M-3
OVERHEAD CONSOLE, SPECIAL TOOLS . . . 8M-7
PAD - INSTALLATION, REAR FASCIA - SCUFF .............................. 13-5
PAD - REMOVAL, REAR FASCIA - SCUFF . . . 13-5
PAD ASSEMBLY - INSTALLATION, INSTRUMENT PANEL TOP ..............23-77PAD ASSEMBLY - REMOVAL,
INSTRUMENT PANEL TOP ..............23-77
PAINT CODE - DESCRIPTION ..........23-101
PAINTED TOUCH-UP - DESCRIPTION ....23-101
PAN - CLEANING, OIL .................9-142
PAN - INSPECTION, OIL ...............9-143
PAN - INSTALLATION, OIL .........9-143,9-55
PAN - REMOVAL, OIL .............9-142,9-55
PAN PANEL-THIRD ROW - FOLD-IN- FLOOR - INSTALLATION, BOTTOM OF
SEAT CUSHION ..................... 23-152
PAN PANEL-THIRD ROW - FOLD-IN- FLOOR - REMOVAL, BOTTOM OF SEAT
CUSHION .......................... 23-152
PANEL - INSTALLATION, BENCH SEAT BACK ............................. 23-144
PANEL - INSTALLATION, FRONT SEAT BACK ............................. 23-113
PANEL - INSTALLATION, GLASS ........23-173
PANEL - INSTALLATION, LEFT D-PILLAR TRIM .............................. 23-94
PANEL - INSTALLATION, LEFT QUARTER TRIM .............................. 23-94
PANEL - INSTALLATION, LOWER INSTRUMENT ....................... 23-73
PANEL - INSTALLATION, RIGHT D-PILLAR TRIM ...................... 23-98
PANEL - INSTALLATION, RIGHT QUARTER TRIM ...................... 23-97
PANEL - INSTALLATION, TRIM .....23-20,23-34,
23-43
PANEL - REMOVAL, BENCH SEAT BACK . . . 23-143
PANEL - REMOVAL, FRONT SEAT BACK . . 23-112
PANEL - REMOVAL, GLASS ............23-173
PANEL - REMOVAL, LEFT D-PILLAR TRIM .............................. 23-94
PANEL - REMOVAL, LEFT QUARTER TRIM .............................. 23-94
PANEL - REMOVAL, LOWER INSTRUMENT ....................... 23-73
PANEL - REMOVAL, RIGHT D-PILLAR TRIM .............................. 23-97
PANEL - REMOVAL, RIGHT QUARTER TRIM .............................. 23-97
PANEL - REMOVAL, TRIM ....23-20,23-34,23-43
PANEL - SECOND ROW -FOLD-IN-FLOOR - INSTALLATION, SEAT BACK ..........23-134
PANEL - SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT BACK ..............23-134
PANEL - THIRD ROW -FOLD-IN-FLOOR - INSTALLATION, SEAT BACK ............23-158
PANEL - THIRD ROW -FOLD-IN-FLOOR - REMOVAL, SEAT BACK ...............23-158
PANEL ADJUSTMENT, ADJUSTMENTS - SUNROOF GLASS ................... 23-173
PANEL ANTENNA CABLE - INSTALLATION, INSTRUMENT ...........8A-12
PANEL ANTENNA CABLE - REMOVAL, INSTRUMENT ....................... 8A-12
PANEL ASSEMBLY - INSTALLATION, INSTRUMENT ....................... 23-70
PANEL ASSEMBLY - REMOVAL, INSTRUMENT ....................... 23-67
PANEL CENTER BEZEL - INSTALLATION, INSTRUMENT ....................... 23-72
PANEL CENTER BEZEL - REMOVAL, INSTRUMENT ....................... 23-71
PANEL DEMISTER DUCTS - INSTALLATION, INSTRUMENT ...........24-54
PANEL DEMISTER DUCTS - REMOVAL, INSTRUMENT ....................... 24-54
PANEL DUCTS - INSTALLATION, INSTRUMENT ....................... 24-55
PANEL DUCTS - REMOVAL, INSTRUMENT ....................... 24-55
PANEL OUTLETS, INSTALLATION - INSTRUMENT ....................... 24-45
PANEL OUTLETS, REMOVAL - INSTRUMENT ....................... 24-45
PANEL REPAIR - STANDARD PROCEDURE, PLASTIC BODY ............23-3
PANEL RIGHT END CAP - INSTALLATION, INSTRUMENT ....................... 23-72
PANEL RIGHT END CAP - REMOVAL, INSTRUMENT ....................... 23-72
PANEL TOP COVER - INSTALLATION, INSTRUMENT ....................... 23-72
22 INDEXRS
Description Group-Page Description Group-Page Description Group-Page