2004 YAMAHA YZF-R1S ignition

8-16
YESNO
3. Starter motor

Connect the positive battery terminal and
starter motor lead with a jumper lead .
Repair or replace the
starter motor.
A wire that is used as a jumper lead
must have at least the same capacity or
more as that of the battery lead, other-
wise the jumper lead may burn.

This check is likely to produce sparks,
therefore make sure nothing flammable
is in the vicinity.

Does the starter motor turn?
WARNING
1
23
EAS00758
YESNO 2. Battery

Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in chapter 3.
Minimum open-circuit voltage
12.8 V or more at 20C (68F)

Is the battery OK?

Clean the battery
terminals.

Recharge or re-
place the battery.
EAS00739
ELECTRIC STARTING SYSTEMELEC
NOTE:
YESNO
1. Main and ignition fuses

Check the main and ignition fuses for conti-
nuity.
Refer to “CHECKING THE FUSES” in chap-
ter 3.

Are the main and ignition fuses OK?
Replace the fuse(s).
EAS00757
TROUBLESHOOTING
The starter motor fails to turn.
Check:
1. main and ignition fuses
2. battery
3. starter motor
4. starting circuit cut-off relay
5. starter relay
6. main switch
7. engine stop switch
8. neutral switch
9. sidestand switch
10. clutch switch
11. start switch
12. wiring connections
(of the entire starting system)

Before troubleshooting, remove the following
part(s):
1. seat
2. fuel tank
3. side cowlings
4. throttle body assembly

Troubleshoot with the following special tool(s).
Pocket tester
90890-03112, YU-3112
EAS00738
ProCarManuals.com

8-25
NOYES
3. Charging voltage

Set the engine tachometer to the ignition coil
of cylinder #1.

Connect the pocket tester (DC 20 V) to the
battery as shown.
The charging circuit
is OK. Positive tester probe

positive battery terminal
Negative tester probe

negative battery terminal

Start the engine and let it run at approxi-
mately 5,000 r / min.

Measure the charging voltage.
Charging voltage
14 V at 5,000 r / min

Is the charging voltage within specification?
EAS00775
YESNO

Clean the battery
terminals.

Recharge or re-
place the battery.
Make sure the battery is fully charged.
NOTE:
Minimum open-circuit voltage
12.8 V or more at 20C (68F)

Is the battery OK?
CHARGING SYSTEMELEC
NOTE:
YESNO
1. Main fuse

Check the main fuse for continuity.
Refer to “CHECKING THE FUSES” in chap-
ter 3.

Is the main fuse OK?
Replace the fuse.
2. Battery

Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in chapter 3.
EAS00739 EAS00774
TROUBLESHOOTING
The battery is not being charged.
Check:
1. main fuse
2. battery
3. charging voltage
4. stator coil lead
5. stator coil resistance
6. wiring connections
(of the entire charging system)

Before troubleshooting, remove the following
part(s):
1. seat
2. fuel tank

Troubleshoot with the following special tool(s).
Pocket tester
90890-03112, YU-3112
EAS00738
ProCarManuals.com

8-35
SIGNALING SYSTEMELEC
1Main switch
4Fuse (main)
6Battery
10Starting circuit cut-off relay
11Neutral switch
13Fuel pump
14E.C.U.
27Speed sensor
38Fuel level warning light
39Oil level warning light
40Neutral indicator light
41Tachometer
42Shift timing indicator light
43Multi function meter
45Coolant temperature indicator light
47Turn signal indicator light (left)
48Turn signal indicator light (light)
55Turn signal relay
58Horn switch
60Turn signal switch
61Horn
62Front turn signal / position light (left)
63Front turn signal / position light (right)
64Rear turn signal light (left)
65Rear turn signal light (right)
73Fuse (ignition)
74Fuse (signal)
ProCarManuals.com

8-36
YESNO

Clean the battery
terminals.

Recharge or re-
place the battery.
EAS00749
3. Main switch

Check the main switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the main switch OK?
YESNO
Replace the main
switch.
YESNO 1. Horn switch

Check the horn switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the horn switch OK?
Replace the left han-
dlebar switch.
EAS00796
CHECKING THE SIGNALING SYSTEM
1. The horn fails to sound.
EAS00795
4. Wiring

Check the entire signaling system’s wiring.
Refer to “CIRCUIT DIAGRAM”.

Is the signaling system’s wiring properly
connected and without defects?
YESNO
Properly connect or
repair the signaling
system’s wiring.
Check the condition
of each of the signal-
ing system’s circuits.
Refer to “CHECK-
ING THE LIGHTING
SYSTEM”.
SIGNALING SYSTEMELEC
NOTE:
YESNO
1. Backup, main, ignition, signal and park
fuses

Check the backup, main, ignition, signal and
park fuses for continuity.
Refer to “CHECKING THE FUSES” in chap-
ter 3.

Are the backup, main, ignition, signal and
park fuses OK?
Replace the fuse(s).
2. Battery

Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in chapter 3.
Minimum open-circuit voltage
12.8 V or more at 20C (68F)

Is the battery OK?
EAS00739EAS00794
TROUBLESHOOTING

Any of the following fail to light: turn sig-
nal light, brake light or an indicator light.

The horn fails to sound.
Check:
1. backup, main, ignition, signal, and park
fuses
2. battery
3. main switch
4. wiring connections
(of the entire signaling system)

Before troubleshooting, remove the following
part(s):
1. seat
2. fuel tank
3. side cowlings

Troubleshoot with the following special tool(s).
Pocket tester
90890-03112, YU-3112
EAS00738
ProCarManuals.com

8-44
1Main switch
4Fuse (main)
6Battery
14E.C.U.
28Coolant temperature sensor
73Fuse (ignition)
76Radiator fan motor relay
77Fuse (radiator fan motor left)
78Fuse (radiator fan motor right)
79Radiator fan motor 2
80Radiator fan motor 1
COOLING SYSTEMELEC
ProCarManuals.com

8-45
YESNO 2. Battery

Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in chapter 3.
Minimum open-circuit voltage
12.8 V or more at 20C (68F)

Is the battery OK?

Clean the battery
terminals.

Recharge or re-
place the battery.
EAS00739
EAS00749
3. Main switch

Check the main switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the main switch OK?
YESNO
Replace the main
switch.
COOLING SYSTEMELEC
NOTE:
YESNO
1. Main, ignition and radiator fan motor fuses

Check the main, ignition and radiator fan
motor fuses for continuity.
Refer to “CHECKING THE FUSES” in chap-
ter 3.

Are the main, ignition and radiator fan motor
fuses OK?
Replace the fuse(s).
EAS00808
TROUBLESHOOTING

The radiator fan motor fails to turn.

The coolant temperature indicator light
fails to light when the engine is warm.
Check:
1. main, ignition, and radiator fan motor fuses
2. battery
3. main switch
4. radiator fan motor
5. radiator fan motor relay
6. coolant temperature sensor
7. wiring connections
(the entire cooling system)

Before troubleshooting, remove the following
part(s):
1. seat
2. fuel tank
3. side cowlings

Troubleshoot with the following special tool(s).
Pocket tester
90890-03112, YU-3112
EAS00738
ProCarManuals.com

8-49
FUEL PUMP SYSTEMELEC
1Battery
2Fuse (main)
3Main switch
4Fuse (ignition)
5Engine stop switch
6ECU
7Fuse (fuel injection)
8Starting circuit cut-off relay (fuel injection
system relay)
9Fuel pump
EAS00815
FUEL PUMP SYSTEM
The ECU includes the control unit for the
fuel pump.
ProCarManuals.com

8-50
FUEL PUMP SYSTEMELEC
YESNO 2. Battery

Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in chapter 3.
Minimum open-circuit voltage
12.8 V or more at 20C (68F)

Is the battery OK?

Clean the battery
terminals.

Recharge or re-
place the battery.
EAS00739
EAS00749
3. Main switch

Check the main switch for continuity.
Refer to “CHECKING THE SWITCHES”.
YESNO
Replace the main
switch.
Is the main switch OK?
EAS00750
4. Engine stop switch

Check the engine stop switch for continuity.
Refer to “CHECKING THE SWITCHES”.
YESNO
Replace the right
handlebar switch.
Is the engine stop switch OK?
NOTE:
YESNO
1. Main, ignition and fuel injection system
fuses

Check the main, ignition and fuel system
fuses for continuity.
Refer to “CHECKING THE FUSES” in chap-
ter 3.
Replace the fuse(s).

Are the main, ignition and fuel injection sys-
tem fuses OK?
EAS00816
TROUBLESHOOTING
If the fuel pump fails to operate.
Check:
1. main, ignition and fuel injection fuses
2. battery
3. main switch
4. engine stop switch
5. starting circuit cut-off relay
(the fuel injection system relay)
6. fuel pump
7. wiring connections
(the entire fuel system)

Before troubleshooting, remove the following
part(s):
1. seat
2. fuel tank
3. side cowlings
Troubleshoot with the following special tool(s).
Pocket tester
90890-03112, YU-3112
EAS00738
ProCarManuals.com