2004 YAMAHA YZF-R1S clutch

2-25
LUBRICATION POINTS AND LUBRICANT TYPESSPEC
EAS00031
LUBRICATION POINTS AND LUBRICANT TYPES
ENGINE
Lubrication point
Lubricant
Oil seal lips
O-rings
Bearings
Crankshaft pins
Piston surfaces
Piston pins
Crankshaft journals
Camshaft lobes
Camshaft journals
Valve stems (intake and exhaust)
Valve stem ends (intake and exhaust)
Water pump impeller shaft
Oil pump rotors (inner and outer)
Oil pump housing
Oil strainer
Clutch (pull rod)
Oil / water pump drive sprocket and washer
Clutch (thrust plate)
Starter clutch idle gear inner surface
Starter clutch assembly
Primary driven gear
Transmission gears (wheel and pinion)
Main axle and drive axle
Shift drum
Shift forks and shift fork guide bars
Shift shaft
Shift shaft boss
Cylinder head cover mating surfaceYamaha bond
No.1215
Crankcase mating surfaceYamaha bond
No.1215
Clutch cover (crankcase mating surface)Yamaha bond
No.1215
Generator rotor cover (crankcase mating surface)Yamaha bond
No.1215
Pickup rotor coverYamaha bond
No.1215
ProCarManuals.com

2-26
LUBRICATION POINTS AND LUBRICANT TYPESSPEC
EAS00032
CHASSIS
Lubrication point
Lubricant
Steering bearings and bearing races (upper and lower)
Throttle grip inner surface
Brake lever pivoting point and metal-to-metal moving parts
Clutch lever pivoting point and metal-to-metal moving parts
Engine mount bolts (rear upper and lower)
Relay arm, connecting rod and rear shock absorber collar
Pivot shaft
Swingarm pivot bearing
Swingarm head pipe end, oil seal and bush
Oil seal (relay arm, connecting arm and rear shock absorber)
Seat lock assembly moving parts
Sidestand pivoting pint and metal-to-metal moving parts
Link and sidestand switch contact point
Sidestand hook and spring
Shift shaft joint
Front wheel oil seal (right and left)
Front axle shaft
Rear wheel oil seal
Rear wheel drive hub oil seal
Rear wheel drive hub mating surface
ProCarManuals.com

2-37
F Clamp the leads inside the front
fork of the vehicle. Point the exit
of the horn lead to the left front
fork side.
G Two throttle cables should not
cross with each other.
Route two throttle cables behind
the brake hose, pass between
the inside of the under bracket’s
upper side front fork and guide
wire assembly, and then pass it
through the clamp that is in-
serted to the cover 3 under the
frame.A Route the clutch cable so as to
get along the front side of the
main switch after passing it
through the guide.
B Pass the main switch lead
through the guide wire.
C Pass the left handlebar switch
lead through the guide wire.
D Point the tip of the band (exces-
sive part) to the rear side of the
vehicle and cut the surplus sec-
tion. Clamp it to the outer tube.
E Clamp the section between 0
and 20 mm (0 and 0.79 in) from
the split of the under bracket.
CABLE ROUTINGSPEC
1Right handlebar switch lead
2Clutch cable
3Main switch lead
4Left handlebar switch lead
5Horn lead
6Horn
7Throttle cables
8Brake hose
9Throttle cable (return side)
10Throttle cable (pull side)
ProCarManuals.com

2-39
E Clamp the clamp upper end
along the line of lower end of the
hose clamp assembly. Point the
tip of the clamp (surplus section)
to the front side of the vehicle.
Clutch cable is what the clamp
fastens.
F The clutch cable doesn’t project
outside the water hose and the
cylinder head in the box part in
the figure.
G To the engine
H Clamp behind the bracket 3.17Throttle body lead
A Clamp it after passing between
the frame and radiator stay.
Point the tip of the clamp (exces-
sive part) to the front side of the
vehicle. Fasten the right handle-
bar switch lead with a clamp.
B To the wire harness
C The clutch cable positioning
guide should be above the upper
end of the clamp. Fasten the
clutch cable with a clamp. (Refer
to )
D Position relation between the
clamp and guide.
M
CABLE ROUTINGSPEC
1Wire harness
2Crankshaft position sensor lead
3Heat protector
4Right handlebar switch lead
5Positioning guide
6Rear brake light switch lead
7Coolant reservoir tank
8Speed sensor lead
9Clutch cable
10Radiator
11Oil cooler outlet hose
12Coolant reservoir tank drain
hose
13Breather pipe
14Fuel tank drain hose
15A.C. magneto lead
16Wire harness
ProCarManuals.com

2-40
P To the air filter
Q Route the fuel tank drain hose
over the canister stay and be-
tween the breather hose 2 and
wire harness. On the front side of
the canister stay, let though the
bottom of the A.C.magneto lead
and the wire harness.
R Route by the upside of vehicle
away from the canister stay.
CABLE ROUTINGSPEC
I The coupler for the air induction
solenoid lead and camshaft sen-
sor lead should be connected
above the ignition coil sub wire
harness and it should not drop
on the cylinder head cover be-
hind the ignition coil.
J Pass the right handlebar switch
lead between the frame and heat
protector.
K Coolant reservoir tank drain
hose should cross with the
speed sensor lead under the
swingarm bracket. Route the
coolant reservoir tank drain hose
over the up side of the vehicle.L Pass the rear brake light switch
lead between the swingarm
bracket and coolant reservoir
tank.
M Release the tip of the clamp and
install it to the clutch cable.
Insert the clamp to the hole lo-
cated on the right back side of
the radiator.
Radiator fan motor lead should
not be caught while inserting the
clamp.
N Push the clamp until it hits the ra-
diator side stay. Radiator fan mo-
tor lead should not be caught.
O Clamp the clutch cable so that it
is within this specified clamp.
ProCarManuals.com

3-1
3
INTRODUCTION / PERIODIC MAINTENANCE CHART FOR THE EMISSION
CONTROL SYSTEM / GENERAL MAINTENANCE AND LUBRICATION CHARTCHK
ADJ
EAS00036
PERIODIC CHECKS AND ADJUSTMENTS
INTRODUCTION
This chapter includes all information necessary to perform recommended checks and adjustments. If
followed, these preventive maintenance procedures will ensure more reliable vehicle operation, a
longer service life and reduce the need for costly overhaul work. This information applies to vehicles
already in service as well as to new vehicles that are being prepared for sale, All service technicians
should be familiar with this entire chapter.
PERIODIC MAINTENANCE CHART FOR THE EMISSION CONTROL SYSTEM
INITIALODOMETER READINGS
No.ITEMROUTINE600 mi
(1000 km)
or
1 month4000 mi
(7000 km)
or
6 months8000 mi
(13000 km)
or
12 months12000 mi
(19000 km)
or
18 months16000 mi
(25000 km)
or
24 months20000 mi
(31000 km)
or
30 months
1*Fuel line
(See page 3-33)
Check fuel hoses for cracks or damage.

Replace if necessary.





2*Spark plugs
(See page 3-23)
Check Condition.

Adjust gap and clean.

Replace every 8000 mi (13000 km) or 12
months.
Replace.
Replace.

3*Valve clearance
(See page 3-11)
Check and adjust valve clearance when en-
gine is cold.Every 26600 mi (42000 km)
4*Crankcase breather
system
(See page 3-34)
Check breather hose for cracks or damage.

Replace if necessary.





5*Electronic fuel injection
(See page 3-17, 21)
Check and adjust engine idle speed and syn-
chronization.






6*Exhaust system
(See page 3-35)
Check for leakage.

Tighten if necessary.

Replace gasket(s) if necessary.





7*Evaporative emission
control system
(For California only)
Check control system for damage.

Replace if necessary.


8*Air induction system
(See page 7-46)
Check the air cut-off valve, reed valve, and
hose for damage.

Replace any damaged parts if necessary.


GENERAL MAINTENANCE AND LUBRICATION CHART
INITIALODOMETER READINGS
No.ITEMROUTINE600 mi
(1000 km)
or
1 month4000 mi
(7000 km)
or
6 months8000 mi
(13000 km)
or
12 months12000 mi
(19000 km)
or
18 months16000 mi
(25000 km)
or
24 months20000 mi
(31000 km)
or
30 months
1*Air filter element
(See page 3-32)
Check condition and damage.
Replace if necessary.





2*Clutch
(See page 3-31)
Check operation.
Adjust or replace cable.






3*Front brake
(See page 3-42, 44, 45)
Check operation, fluid level, and for fluid leak-
age.

Replace brake pads if necessary.






4*Rear brake
(See page 3-43, 44, 45)
Check operation, fluid level, and for fluid leak-
age.

Replace brake pads if necessary.






5*Brake hoses
Check for cracks or damage.




5*Brake hoses(See page 3-46)
Replace.Every 4 years
6*Wheels
(See page 4-3)
Check runout and for damage.
Replace if necessary.





7*Tires
(See page 3-58)
Check tread depth and for damage.
Replace if necessary.
Check air pressure.
Correct if necessary.






8*Wheel bearings
(See page 4-3)
Check bearings for smooth operation.
Replace if necessary.





ProCarManuals.com

3-2
NOTE:
GENERAL MAINTENANCE AND LUBRICATION CHART
CHK
ADJ
NOTE:
INITIALODOMETER READINGS
No.ITEMROUTINE600 mi
(1000 km)
or
1 month4000 mi
(7000 km)
or
6 months8000 mi
(13000 km)
or
12 months12000 mi
(19000 km)
or
18 months16000 mi
(25000 km)
or
24 months20000 mi
(31000 km)
or
30 months
9*Swingarm pivot
bearings
(See page 4-71)
Check bearing assemblies for looseness.
Moderately repack with lithium-soap-based
grease.
Repack.
10Drive chain
(See page 3-49, 50)
Check chain slack/alignment and condition.
Adjust and lubricate chain with a special O-
ring chain lubricant thoroughly.Every 600 mi (800 km) and after washing the motorcycle or riding in the rain
11*Steering bearings
(See page 3-51)
Check bearing assembly for looseness.
Moderately repack with lithium-soap-based
grease every 16000 mi (25000 km) or 24
months.



Repack.

12*Steering damper
(See page 4-60)
Check operation and for oil leakage.





13*Chassis fasteners
(See page 2-23)
Check all chassis fitting and fasteners.
Correct if necessary.





14Brake and clutch
lever pivot shafts
(See page 3-61)
Apply lithium-soap-based grease (all-purpose
grease) lightly.





15Sidestand pivot(See page 3-61)

Check operation.

Apply lithium-soap-based grease (all-pur-
pose grease) lightly.





16*Sidestand switch
(See page 3-61, 8-4)
Check operation and replace if necessary.






17*Front fork
(See page 3-53)
Check operation and for oil leakage.
Replace if necessary.





18*Shock absorber
assembly
(See page 3-56, 4-67)
Check operation and for oil leakage.
Replace if necessary.





19*Rear suspension
link pivots
(See page 4-71)
Check operation.
Correct if necessary.


20Engine oil
(See page 3-26, 28)
Change (warm engine before draining.)






21*Engine oil filter cartridge
(See page 3-28)
Replace.



22*Cooling system

Check hoses for cracks or damage.
Replace if necessary.





22*Cooling system(See page 3-37, 38, 39)
Change with ethylene glycol antifreeze cool-
ant every 24 months.Change.
23*EXUP system
(See page 3-36)
Check operation, cable free play and pulley
position.
Every 12000 mi (19000 km)
24*Control cables
(See page 3-61)
Apply Yamaha chain and cable lube or en-
gine oil SAE 10W-30 thoroughly.






25*Throttle grip housing
and cable
(See page 3-22)
Check operation and free play.
Adjust the throttle cable free play if necessary.
Lubricate the throttle grip housing and cable.





* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi
(13000 km) or 12 months.
Air filter

This model’s air filter is equipped with a disposable oil-coated paper element, which must not be
cleaned with compressed air to avoid damaging it.

The air filter element needs to be replaced more frequently when riding in unusually wet or dusty areas.
Hydraulic brake service

After disassembling the brake master cylinders and calipers, always change the fluid. Regularly
check the brake fluid levels and fill the reservoirs as required.

Every two years replace the internal components of the brake master cylinders and calipers, and
change the brake fluid.

Replace the brake hoses every four years and if cracked or damaged.
ProCarManuals.com

3-31
MEASURING THE ENGINE OIL PRESSURE /
ADJUSTING THE CLUTCH CABLE FREE PLAYCHK
ADJ
8 Nm (0.8 m
kg, 5.8 ft
lb)
CAUTION:
c
b
NOTE:Engine oil pressure
Possible causes
Below
ifi i
Faulty oil pump
specificationClogged oil filter
Leaking oil
passage
Broken or
damaged oil seal
Above
specificationLeaking oil
passage
Faulty oil filter
Oil viscosity too
high
7. Install:

oil gallery bolt
1
Be carful to tighten too much.
8. Install:

bottom cowlings
Refer to “COWLINGS”.
EAS00078
ADJUSTING THE CLUTCH CABLE FREE
PLAY
1. Check:

clutch cable free play
a
Out of specification
Adjust.
Clutch cable free play (at the
end of the clutch lever)
10  15 mm (0.39  0.59 in)
2. Adjust:

clutch cable free play
Handlebar side
a. Turn the adjusting dial
1 in direction b or c
until the specified clutch cable free play is ob-
tained.
Direction
Clutch cable free play is
increased.
DirectionClutch cable free play is
decreased.
If the specified clutch cable free play cannot be
obtained on the handlebar side of the cable, use
the adjusting nut on the engine side.
ProCarManuals.com