Page 24 of 382
SPECGENERAL SPECIFICATIONS
2-3
Item Standard Limit
Brakes
Front:
Type Single Ø 267 mm disk brake,
2 x 28 mm
Operation Right hand
Fluid DOT 4
Rear:
Type Single Ø 220 mm disk brake,
1 x 34 mm caliper
Operation Right foot
Fluid DOT 4
Suspension
Front Telescopic fork Outside tube
dia. 46 mm
Rear Deltabox Swingarm with
adjustable shock absorber
Spring/shock absorber
Front Coil spring / oil damper
RearCoil spring / gas-oil damper, spring
preload adjustable
Wheel travel
Front 230 mm •••
Rear 230 mm •••
Electrical system
Ignition system Transistorized coil ignition (digital)
Charging system:
Type A.C. magneto
Standard output 14V, 13.5A at 5.000 r/min •••
Battery:
Model GT9B-4
Voltage, capacity 12V, 8Ah •••
Headlight typeQuartz bulb (halogen)
Bulb voltage, wattage x quantity
Headlight 12V 60W / 55W x 1 •••
Tail/brake light 12V 5W / 21W x 1 •••
Turn signal light 12V 10W x 4 •••
Auxiliary light 12V 5W x 1 •••
Meter lighting 12V 3W x 1 •••
Turn signal indicator light 12V 1.2W x 1 •••
Neutral indicator light 12V 1.2W x 1 •••
Auxiliary indicator light 12V 1.2W x 1 •••
High beam indicator light 12V 1.2W x 1 •••
Fuse20A •••
ProCarManuals.com
Page 108 of 382
CHECKING THE FUSES/
REPLACING THE HEADLIGHT BULBS
3-54
INSP
ADJ
WARNING
Never use a fuse with an amperage rating
other than that specified. Improvising or using
a fuse with the wrong amperage rating may
cause extensive damage to the electrical sys-
tem, cause the lighting and ignition systems
to malfunction and could possibly cause a fire.
4. Install:
•Pannel
•Seat
REPLACING THE HEADLIGHT BULBS
Low beam/high beam
1. Remove:
•Cowling screws (1)
2. Remove:
•Cowling (from the meter bracket)
NOTE:
Remove the cowling from the meter bracket by
lowering it to disengage it, and then lifting it up.
3. Remove:
•Headlight (2)
4. Disconnect:
•Headlight coupler (3)
5. Remove:
•Headlight bulb cover (4)
6. Remove:
•Headlight bulb holder (5) (by turning it
counterclockwise (a))
•Headlight bulb
WARNING
Headlight bulbs get very hot. Therefore, keep
flammable products away from a lit headlight
bulb, and do not touch the bulb until it has
cooled down.
ProCarManuals.com
Page 347 of 382
ELECLIGHT SYSTEM
7-43
DIAGNOSTICS THE HIGH BEAM LIGHT, PARKING INDICATOR LIGHT, REAR LIGHT, FRONT PARKING LIGHT AND/OR INSTRUMENT LIGHTS FAIL TO TURN ON.
Procedure
Inspect:
1. Fuse
2. Battery
3. Main switch 4. Dipped/high beam light and dimmer switch
5. Relay assy
6. Harness connections (full system of connec- tions)
NOTE:
•Before starting inspections, remove the following parts:
1. Seat
2. Rear cowling
3. Cowling (headlight)
4. Tail light cover
•To check for defects use the following special tools.
Pocket tester: P/N. 90890-03112
1. Fuse
•Check the fuse for continuity.
Refer to “CHECKING THE FUSES” in
Chapter 3.
•Is the fuse OK?
YES
2. Battery
•Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in Chapter 3.
Min. open-circuit voltage:
12.8 V or more at 20°C (68°F)
•Is the battery OK?
NO
Replace the fuse.
NO
•Clean the battery terminals.
•Recharge or replace the battery.
YES
*
ProCarManuals.com
Page 348 of 382
LIGHT SYSTEM
7-44
ELEC
3. Main switch.
•Disconnect the main switch connector
from the wire harness.
•Connect the pocket tester ( Ωx 1) to the
switch cables.
Refer to “SWITCH CHECK” in CHAPTER
3.
CORRECT
INCORRECT
The main switch is defective. Replace.
*
4. Dipped/high beam commutator and dim-
mer switch.
•Disconnect the left handlebar switch con-
nector from the wire harness.
•Connect the pocket tester ( Ωx 1) to the
left handlebar switch terminals.
•Check the switch component for conti-
nuity between “Brown (1)” and “Yellow
(2)”, “Brown/Blue (3)” and “Green (4)”,
“Brown/Blue (3)” and “Yellow (2)”.
Refer to “SWITCH CHECK” in CHAPTER
3.
INCORRECT
The dipped/high beam commutator and/or the
dimmer switch are defective. Replace the left
handlebar switch.
$'\f
\f
\f
\f
CORRECT
*
ProCarManuals.com
Page 350 of 382
LIGHT SYSTEM
7-46
ELEC
LIGHT SYSTEM INSPECTION NOTE:
To proceed to the control of the light system, start the engine and then stop it by the emergency engine
stop switch. In this way the light relay remains excited and it is possible to check the light system.
1. The front headlight and the high beam light fail to turn on.
CONTINUITY
DISCONTINUITY
Replace the bulb and/or the bulbholder.1. Bulb and bulbholder.
•Check the continuity of the bulb and bulb-
holder.
Refer to “BULB INSPECTION” section.
2. Voltage.
•Connect the pocket tester (DC 20V) to the
front headlight connectors and the high
beam switch.
Headlight: Tester terminal (+) ➔
Green (2) or Yellow (1) cable
Tester terminal (–) ➔Black cable (3)
High beam light: Tester terminal (+) ➔Yellow cable (4)
Tester terminal (–) ➔Black cable (5)
[A] When the lights switch (commutator) is at
position “HI”.
[B] When the lights switch (commutator) is at position “LO”.
OUT OF SPECIFICATION
The circuit from the main switch to the bulbhol-
der connector is defective. Repair.
A
B
ProCarManuals.com
