2004 YAMAHA TT600RE relay

CHASDRIVE CHAIN, DRIVE SPROCKET AND REAR WHEEL SPROCKET
4-85
3. Tighten:
•Rear wheel sprocket fastening bolts
Rear wheel sprocket fastening bolts: 48 Nm (4.8 mkg)
Nut (drive sprocket): 110 Nm (11.0 mkg)
Nut (swingarm pivot shaft): 90 Nm (9.0 mkg)
Nut (frame-relay arm): 60 Nm (6.0 mkg)
▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲
DRIVE CHAIN INSTALLATION
Perform “REMOVAL” operations in reverse order.
Pay special attention to the following points.
1. Install:
•Drive chain
•Swingarm
2. Install:
•Rear wheel
Refer to “REAR WHEEL INSTALLATION”
section.
3. Install:
•Drive sprocket
WARNING
Always use a new lock washer.
NOTE:
•Tighten the drive sprocket nut with the rear
brake pulled.
•After tightening the nut, bend the tab on the
lock washer once more over the faces of the
nut.
4. Adjust:
•Drive chain slack
Refer to “DRIVE CHAIN SLACK ADJUST-
MENT” section in CHAPTER 3.
Drive chain slack: 30 ~ 40 mm
ProCarManuals.com

ELECTRICAL CIRCUIT DIAGRAM
7-2
ELEC
B Black B/Y Black/Yellow
Br Brown Br/B Brown/Black
Ch Chocolate Br/W Brown/White
Dg Deep green G/B Green/Black
G Green G/R Green/Red
Gy Grey G/W Green/White
L Blue G/Y Green/Yellow
Or Orange L/R Blue/Red
P Pink L/W Blue/White
R Red L/Y Blue/Yellow
Sb Sky-blue R/B Red/Black
W White R/W Red/White
Y Yellow R/Y Red/Yellow
B/R Black/Red W/L White/Blue
B/W Black/White Y/R Yellow/Red
(1) AC generator/Pickup coil
(2) Rectifier/Regulator
(3) Battery
(4) Starter relay
(5) Starting motor
(6) Fuse
(7) Main switch
(8) Right handlebar switch
(9) Engine stop switch
(10) Starter switch
(11) Diode
(12) Clutch switch
(13) Sidestand switch
(14) Neutral switch
(15) Diode
(16) Ignitor unit
COLOUR CODE (17) Ignition coil
(18) Left handlebar switch
(19) Horn switch
(20) Diode
(21) Pass switch
(22) Dimmer switch
(23) Flasher switch
(24) Horn
(25) Flasher relay
(26) Headlight
(27) Flasher light
(28) Relay assy
(29) Front brake switch
(30) Rear brake switch
(31) Tail/stop light
(32) Meter
ProCarManuals.com

ELECELECTRICAL COMPONENTS
7-3
ELECTRICAL COMPONENTS
(1) Main wire harness
(2) Diodes
(3) Extension wire harness
(4) Rectifier/Regulator
(5) CDI ignition unit
(6) Battery (12V – 8Ah)
(7) Starter relay
(8) Fuse (20A) BATTERY: CAPACITY 12V – 8Ah
SPECIFIC GRAVITY: 1.320
ProCarManuals.com

ELECTRICAL COMPONENTS
7-4
ELEC
IGNITION COIL: Primary winding resistance: 4 Ω
Ω
± 15% at 20°C (68°F)
Secondary winding resistance: 13 k Ω
Ω
± 20% at 20°C (68°F)(1) Ignition coil
(2) Spark plug cap
(3) Flasher relay
(4) Horn
(5) Clutch switch
(6) Relay assy
(7) Sidestand switch
(8) Neutral switch
(9) Main switch
ProCarManuals.com

ELECTRICAL STARTING SYSTEM
7-22
ELEC
The diagram illustrates the electrical starting system-circuit inside the motorcycles electric system. NOTE:
For the colour code and legend, see page 7-2.
(3) Battery
(4) Starter relay
(5) Starting motor
(6) Fuse
(7) Main switch
(9) Engine stop switch (10) Starter switch
(11) Diode
(12) Clutch switch
(13) Sidestand switch
(14) Neutral switch
(15) Diode
\f(

365
12
11141315
4
ProCarManuals.com

ELECELECTRICAL STARTING SYSTEM
7-23
STARTING CIRCUIT OPERATION
The starting circuit on this model consists of the
starter motor, starter relay, and the starting circuit
cut-off relay. If the engine stop switch is on “RUN”
and the main switch is on “ON” (both switches are
closed), the starter motor can operate only if:
The starting circuit cut-off relay prevents the
starter from operating when neither of these con-
ditions have been met. In this instance, the start-
ing circuit cut-off relay is open so current cannot
reach the starter motor.
When at least one of the above conditions have
been met however, the starting circuit cut-off relay
is closed, and the engine can be started by press-
ing the starter switch.
WHEN THE TRANSMISSION IS IN
NEUTRAL
WHEN THE SIDESTAND IS UP AND
THE CLUTCH LEVER IS PULLED IN
1 Battery
2 Main switch
3 Engine stop switch
4 Starter relay
5 Starting circuit cut-off relay
6 Start switch
7 Starter motor
8 Neutral switch
9 Clutch switch
0 Sidestand switch
The transmission is in neutral (the neutral
switch is closed). or if
The clutch lever is pulled to the handlebar (the
clutch switch is closed) and the sidestand is up
(the sidestand switch is closed).
ProCarManuals.com

ELECTRICAL STARTING SYSTEM
7-24
ELEC
DIAGNOSTICS THE STARTER FAILS TO WORK
Procedure
Inspect:
(1) Fuse
(2) Battery
(3) Starting motor
(4) Starter relay
(5) Main switch (6) Engine stop switch
(7) Sidestand switch
(8) Neutral switch
(9) Clutch switch
(10) Starter switch
(11) Harness connections
NOTE:
Before starting inspections, remove the following parts:
1. Seat
2. Rear cowling 3. Fuel tank
4. Cowling (headlight)
•To check for defects use the following special tools.
Pocket tester: P/N. 90890-03112
1. Fuse.
•Remove fuse.
•Connect the pocket tester ( Ωx 1) to the
fuse.
•Check the fuse for continuity.
Refer to “CHECKING THE FUSES” in
Chapter 3.
2. Battery.
•Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in Chapter 3.
Min. open-circuit voltage:
12.8 V or more at 20°C (68°F)
CONTINUITY
DISCONTINUTY
Replace the fuse.
INCORRECT
•Clean the battery terminals.
•Recharge or replace the battery.
Refer to “BATTERY INSPECTION” in
Chapter 3.
*
CORRECT
ProCarManuals.com

ELECELECTRICAL STARTING SYSTEM
7-25
IT RUNS
IT FAILS TO RUN The starter is defective. Repair or replace.
IT FAILS TO RUNThe starter relay is defective. Replace.
3. Starter
•Connect the positive terminal of the bat-
tery (1) and the starter cable (2) using a
connection cable (3) *.
•Check the functioning of the starter.
WARNING
• A wire that is used as a jumper lead must have at least the same capacity of the bat-
tery lead, otherwise the jumper lead may
burn.
• This check is likely to produce sparks, therefore make sure that no flammable
gas or fluid is in the vicinity.
*
*
4. Starter relay.
•Disconnect the starter relay connector.
•Connect the battery and frame to the
starter relay connector, using a connec-
tion cable (1) as shown.
Battery terminal (+) (2) ➔
Red/Black terminal (3)
Frame ➔Blue/White terminal (4)
•Check the functioning of the starter.
*
IT RUNS
ProCarManuals.com