2004 SUBARU FORESTER Head light

LI-15
LIGHTING SYSTEM
Headlight Assembly
 This illustration is for LHD model. The pattern for RHD model is symmetrically opposite.
(A) Vehicle center (B) Bulb center
W mm (in) H mm (in) h mm (in) at 3 m (10 ft)
1,140 (44.88) 733 (28.9) 30 (1.18)
LI-00054
H
H W1
W
W W2
W2
W1 (A)
(A)
3m (10 ft)(B) h
h

LI-16
LIGHTING SYSTEM
Headlight Bulb
12.Headlight Bulb
A: REMOVAL
CAUTION:
 Because the halogen bulb operates at a high
temperature, dirt and oil on the bulb surface re-
duces the bulb’s service life. Hold the flange
portion when replacing the bulb. Never touch
the glass portion.
 Do not leave the headlight without a bulb for
a long time. Dust, moisture, etc. entering the
headlight may affect its performance.
1) Disconnect the ground cable from battery.
2) Remove the air intake duct (when removing the
headlight RH).
3) Disconnect the harness connector.
4) Remove the rubber cap.
5) Remove the light bulb retaining spring to remove
the bulb.
B: INSTALLATION
Install in the reverse order of removal.
CAUTION:
Attach the rubber cap with letters TOP on the
top so the drain hole will be on the lower side.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
LI-00017
LI-00018

LI-17
LIGHTING SYSTEM
Front Turn Signal Light Bulb
13.Front Turn Signal Light Bulb
A: REMOVAL
1) Remove the headlight assembly. REMOVAL, Headlight Assembly.>
2) Turn the socket and remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
LI-00021

LI-18
LIGHTING SYSTEM
Clearance Light Bulb
14.Clearance Light Bulb
A: REMOVAL
1) Remove the headlight assembly. REMOVAL, Headlight Assembly.>
2) Turn the socket and remove the bulb.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1) Visually check the bulb for blow out.
2) Check the bulb specification. SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
LI-00022

WIPER AND WASHER SYSTEM
WW
Page
1. General Description ....................................................................................2
2. Wiper and Washer System .........................................................................6
3. Combination Switch (Wiper)........................................................................7
4. Wiper Blade.................................................................................................9
5. Washer Tank and Motor............................................................................11
6. Front Wiper Arm ........................................................................................12
7. Front Wiper Motor and Link.......................................................................13
8. Front Washer Nozzle ................................................................................15
9. Rear Wiper Arm ........................................................................................16
10. Rear Wiper Motor ......................................................................................17
11. Rear Washer .............................................................................................18
12. Wiper Control Relay ..................................................................................19
13. Headlight Washer......................................................................................20

WW-4
WIPER AND WASHER SYSTEM
General Description
3. WASHER TANK
(1) Washer nozzle (7) Grommet (13) Valve
(2) Washer hose (8) Headlight washer motor
(3) Washer tank (9) Motor bracketTightening torque: N·m (kgf-m, ft-lb)
(4) Washer tank cap (10) Headlight washer caseT: 6.0 (0.61, 4.4)
(5) Front washer motor (11) Headlight washer upper nozzle
(6) Rear washer motor (12) Headlight washer lower nozzle
WW-00097
(1) (1)
(1)(2)
(2) (10)
(11)
(12)
(13)
(2)
(2)(8)
(7)
(6) (5)(9)
T
(3)
(4)

WW-11
WIPER AND WASHER SYSTEM
Washer Tank and Motor
5. Washer Tank and Motor
A: REMOVAL
1) Open the hood.
2) Disconnect the ground cable from battery.
3) Remove the two bolts, hose and connector, and
then remove the tank.
4) For the model with headlight washer, proceed to
step 5) and 6).
5) Lift the washer tank, and then disconnect the con-
nector from headlight washer motor. Disconnect
washer hoses.
6) Disconnect the washer hose from the motor, and
then detach the washer tank.
B: INSTALLATION
Install in the reverse order of removal.
Tightening torque:
6.0 N·m (0.61 kgf-m, 4.4 ft-lb)
C: DISASSEMBLY
1) Remove bolt, and then pull out washer motor
from tank. (Model with headlight washer)
2) Pull out the washer motor from tank.
D: ASSEMBLY
1) Assemble in the reverse order of disassembly.
2) Confirm that water does not leak from installa-
tion area of motor.
E: INSPECTION
Apply battery voltage to the connector terminal of
the washer motor and make sure the motor oper-
ates.
WW-00011
WW-00098
WW-00099
WW-00100
WW-00012
WW-00013

WW-20
WIPER AND WASHER SYSTEM
Headlight Washer
13.Headlight Washer
A: REMOVAL
1) Disconnect the ground cable from the battery.
2) Remove the front grille. AL, Front Grille.>
3) Remove the headlight. AL, Headlight Assembly.>
4) Draw out headlight washer hose.
5) Disconnect hose (A) from valve (B).
NOTE:
Washer fluid may drain from valve. Put a pan under
the valve, then disconnect valve from hose while
pinching the hose edge.
6) Remove nozzle cover (A).
7) Push the three pawls to remove outer nozzle (A).
Then pull out inner nozzle (B).
NOTE:
Before pushing the outer nozzle pawls, cover the
bumper to avoid scratches.
B: INSTALLATION
Install in the reverse order of removal.
WW-00102
(B) (A)
(A)
WW-00109
(A)
WW-00110
(A)
(B)