2004 NISSAN PATHFINDER manual transmission

This light comes on when the 4WD shift switch
is set in the 4LO position with ignition key in the
ON position.
If the 4WD shift switch is set in the 4LO position
and the light blinks, stop the vehicle, drive slowly
forward and the light will turn on.
When you shift between 4H and 4LO, stop the
vehicle, move the automatic transmission selec-
tor lever to the N position, and press the 4WD
shift switch and move it in 4LO or 4H.
The transfer case may be damaged if you shift
the switch while driving.
You cannot move the transfer 4WD shift switch
between 4H and 4LO unless you have first
stopped the vehicle and moved the automatic
transmission shift lever to neutral. Make sure the
transfer 4LO position indicator light turns on
when you shift the 4WD shift switch to 4LO.
The indicator light may blink while shifting
from one drive mode to the other.
Turn signal/hazard indicator
lights
The light flashes when the turn signal switch
lever or hazard switch is turned on.
Vehicle dynamic control off
indicator light (if so equipped)
The light comes on when the vehicle dynamic
control off switch is pushed to OFF. This indi-
cates the vehicle dynamic control system and
traction control system are not operating. When
the vehicle dynamic control off indicator light and
slip indicator light come on with the vehicle
dynamic control system turned on, this light
alerts the driver to the fact that the vehicle
dynamic control system’s fail-safe mode is op-
erating, i.e. the vehicle dynamic control system
may not be functioning properly. Have the sys-
tem checked by your NISSAN dealer. If an
abnormality occurs in the system, the vehicle
dynamic control system function will be can-
celed but the vehicle is still driveable. For addi-
tional information, see “Vehicle dynamic control
system (VDC)” in the “5. Starting and driving”
section of this manual.AUDIBLE REMINDERS
Key reminder chimeThe chime will sound when the driver side door
is opened if the key is left in the ignition switch.
Take the ignition key when you leave the vehicle.
Light reminder chimeThe chime will sound when the front door is
opened with the headlight switch on unless the
ignition key is in the ignition switch.Brake pad wear warningThe disc brake pads have audible wear warn-
ings. When a brake pad requires replacement, it
will make a high pitched scraping sound. Have
the brakes checked as soon as possible if the
warning sound is heard when the vehicle is
moving, whether or not the brake pedal is de-
pressed.
2-16
Instruments and controls


04.3.9/R50-D/V5


MEMORY STORAGE FUNCTIONTwo positions for the driver’s seat can be stored
in the automatic drive positioner memory. Follow
these procedures to use the memory system.
1. Set the shift selector lever to the P (Park)
position.
2. Turn the ignition ON.
3. Adjust the driver’s seat to the desired posi-
tions by manually operating each adjusting
switch. For additional information, see
“Seats” in the “1. Seats, restraints and
supplemental air bag systems” section.During this step, do not turn the ignition to
any positions other than ON.
4. Push the SET switch and, within 5 seconds,
push the memory switch (1 or 2) fully for at
least 1 second.
The indicator light for the pushed memory
switch will come on and stay on for approxi-
mately 5 seconds after pushing the switch.
After the indicator light goes off, the selected
positions are stored in the selected memory
(1 or 2).
If memory is stored in the same memory switch,
the previous memory will be deleted.
Confirming memory storage
Turn the ignition ON and push the SET
switch. If the main memory has not been
stored, the indicator light will come on for
approximately 0.5 seconds. When the
memory has stored the position, the indicator
light will stay on for approximately 5 seconds.

If the battery cable is disconnected, or if the
fuse blows, the memory will be canceled. In
such a case, reset the desired positions
using the following procedures.
1. Open and close the driver’s door more than
two times with the ignition key in the LOCK
position.
2. Reset the desired position using the previous
procedure.Selecting the memorized position1. Set the automatic transmission selector lever
to the P (Park) position.
2. Turn the ignition ON.
3. Push the memory switch (1 or 2) fully for at
least 1 second.
The driver’s seat will move to the memorized
position with the indicator light flashing, and
then the light will stay on for approximately 5
seconds.
SPA1164
3-18
Pre-driving checks and adjustments


04.3.9/R50-D/V5


5 Starting and drivingPrecautions when starting and driving ............................. 5-2
Exhaust gas (Carbon monoxide) .................................. 5-2
Three way catalyst ........................................................... 5-3
Low tire pressure warning system (if so
equipped) ........................................................................... 5-3
On-pavement and offroad driving precautions ......... 5-4
Avoiding collision and rollover ...................................... 5-5
Drinking alcohol/drugs and driving .............................. 5-5
Driving safety precautions.............................................. 5-5
Ignition switch ......................................................................... 5-7
Automatic transmission................................................... 5-7
Manual transmission ........................................................ 5-8
Key positions ..................................................................... 5-9
Nissan vehicle immobilizer system............................... 5-9
Before starting the engine ................................................ 5-10
Starting the engine ............................................................. 5-10
Driving the vehicle ............................................................... 5-11
Automatic transmission ................................................ 5-11
Manual transmission ..................................................... 5-16
Parking brake........................................................................ 5-17
Cruise control (if so equipped)........................................ 5-18
Precautions on cruise control .................................... 5-18
Cruise control operations ............................................ 5-19Break-in schedule ............................................................... 5-20
Increasing fuel economy .................................................... 5-20
Using part time four wheel drive (4WD) ....................... 5-21
Transfer case shifting procedures............................. 5-23
Using all-mode four wheel drive (4WD) ....................... 5-25
Transfer case shifting procedures............................. 5-25
Parking/parking on hills...................................................... 5-32
Power steering ..................................................................... 5-33
Brake system ........................................................................ 5-34
Braking precautions ...................................................... 5-34
Anti-lock brake system (ABS) .................................... 5-34
Vehicle Dynamic Control (VDC) system
(if so equipped).................................................................... 5-36
Cold weather driving .......................................................... 5-37
Freeing a frozen door lock .......................................... 5-37
Anti-freeze ....................................................................... 5-37
Battery .............................................................................. 5-37
Draining of coolant water ............................................ 5-37
Tire equipment................................................................ 5-37
Special winter equipment ............................................ 5-38
Driving on snow or ice ................................................. 5-38
Engine block heater (if so equipped) ....................... 5-39


04.3.9/R50-D/V5


road driving and extrication when stuck in deep
snow or mud, or the like.
Please observe the following precautions:
WARNING

Drive carefully when off the road and
avoid dangerous areas. Every person
who drives or rides in this vehicle
should be seated with their seat belt
fastened. This will keep you and your
passengers in position when driving
over rough terrain.

Before driving up or down grades,
check the road surface for bumps or
potholes. Be sure to climb a gentle
slope and descend a gentle slope.

Do not drive across steep slopes.
Instead drive either straight up or
straight down the slopes. Off-road
vehicles can tip over sideways much
more easily than they can forward or
backward.

Many hills are too steep for any ve-
hicle. If you drive up them, you maystall. If you drive down them, you may
not be able to control your speed. If
you drive across them, you may roll
over.

Do not shift gears while driving on
downhill grades as this could cause
loss of control of the vehicle.

Be sure to use the engine brake. The
foot brake performance may be re-
duced, resulting in a possible acci-
dent.

Stay alert when driving to the top of a
hill. At the top there could be a drop-
off or other hazard that could cause
an accident.

If your engine stalls or you cannot
make it to the top of a steep hill,
never attempt to turn around. Your
vehicle could tip or roll over. Always
back straight down in R (Reverse)
gear. Never back down in N (Neutral)
or with the clutch depressed (manual
transmission vehicles), using only the
brake, as this could cause loss of
control.
Heavy braking going down a hill
could cause your brakes to overheat
and fade, resulting in loss of control
and an accident. Apply brakes lightly
and use a low gear to control your
speed.

Unsecured cargo can be thrown
around when driving over rough ter-
rain. Properly secure all cargo so it
will not be thrown forward and cause
injury to you or your passengers.

To avoid raising the center of gravity
excessively, do not exceed the rated
capacity of the roof rack and evenly
distribute the load. Secure heavy
loads in the cargo area as far forward
and as low as possible. Do not equip
the vehicle with tires larger than
specified in this manual. This could
cause your vehicle to roll over.

Do not grip the inside or spokes of
the steering wheel when driving of-
froad. The steering wheel could move
suddenly and injure your hands. In-
stead drive with your fingers and5-6
Starting and driving


04.3.9/R50-D/V5


1) Move the selector lever into the P (Park)
position.
2) Turn the ignition key slightly in the ON direc-
tion.
3) Turn the key toward the LOCK position.
4) Remove the key.
If the key is removed from the ignition switch, the
selector lever cannot be moved from P (Park).
The selector lever can be moved if the
ignition switch is in the ONposition and
the foot brake pedal is depressed.
There is an OFF position in between LOCK and
ACC, although it does not show on the lock
cylinder. When the ignition is in OFF the steering
wheel is not locked.
In order for the steering wheel to be locked, it
must be turned about 1/6 of a turn clockwise
from the straight up position.
To lock the steering wheel, turn the key to
the LOCK position. Remove the key. To
unlock the steering wheel, insert the key
and turn it gently while rotating the steer-
ing wheel slightly right and left.
WARNING
Never remove or turn the key to the
LOCK position while driving. The steer-
ing wheel will lock. This may cause the
driver to lose control of the vehicle and
could result in serious vehicle damage
or personal injury.
MANUAL TRANSMISSIONThe switch includes an anti-theft steering lock
device.
The ignition key can only be removed when the
switch is in the LOCK position.
On manual transmission models, to turn the
ignition key to LOCK from ACC or ON, first turn
the key to OFF and turn the key to LOCK while
pushing the key in.
In order for the steering wheel to be locked, it
must be turned about 1/6 of a turn clockwise
from the straight up position.
To lock the steering wheel, turn the key to
SSD0082C
5-8
Starting and driving


04.3.9/R50-D/V5


Make sure the area around the vehicle is
clear.

Check fluid levels such as engine oil, coolant,
brake and clutch fluid, window washer fluid
as frequently as possible, at least whenever
you refuel.

Check to be sure that all windows and light
lenses are clean.

Visually inspect tires for their appearance and
condition. Also check tires for proper infla-
tion.

Lock all doors.

Position seat and adjust head restraints.

Adjust inside and outside mirrors.

Fasten seat belts and ask all passengers to
do likewise.

Check the operation of warning lights when
key is turned to the ON (3) position.1. Apply the parking brake.
2.Automatic transmission:
Move the selector lever to P (Park position) or
N (Neutral position). (P preferred)
The selector lever cannot be moved out
of P and into any of the other gear
positions if the ignition key is turned to
LOCK or if the key is removed from the
switch.
The starter is designed not to operate if
the selector lever is in one of the driving
positions.
Manual transmission:
Move the gearshift lever to N (Neutral posi-
tion), and depress the clutch pedal to the
floor while starting the engine.
The starter is designed not to operate
unless the clutch pedal is fully de-
pressed.
3. Crank the enginewith your foot off the
accelerator pedalby turning the ignition
key to START. Release the key when the
engine starts. If the engine starts, but fails to
run, repeat the above procedure.

If the engine is very hard to start in extremely
cold weather or when restarting, depress theaccelerator pedal a little (approximately 1/3
to the floor) and hold it then crank the engine.
Release the key and the accelerator pedal
when the engine starts.

If the engine is very hard to start because it is
flooded, depress the accelerator pedal all the
way to the floor and hold it. Crank the engine
for 5 to 6 seconds. After cranking the engine,
release the accelerator pedal. Crank the en-
ginewith your foot off the accelerator
pedalby turning the ignition key to START.
Release the key when the engine starts. If the
engine starts, but fails to run, repeat the
above procedure.
CAUTION
Do not operate the starter for more than
15 seconds at a time. If the engine does
not start, turn the key off and wait 10
seconds before cranking again, other-
wise the starter could be damaged.
4.Warm-up
Always allow the engine to idle for at least 30
seconds after starting. Do not race the en-
gine while warming it up. Drive at moderate
speed for a short distance first, especially in
BEFORE STARTING THE ENGINE STARTING THE ENGINE5-10
Starting and driving


04.3.9/R50-D/V5


MANUAL TRANSMISSION
Shifting
WARNING

Do not downshift abruptly on slip-
pery roads. This may cause a loss of
control.

Do not over-rev the engine when
shifting to a lower gear. This may
cause a loss of control or enginedamage.
To change gears, or when up shifting or down
shifting, depress the clutch pedal fully, shift into
the appropriate gear, then release the clutch
slowly and smoothly.
To ensure smooth gear changes, fully depress
the clutch pedal before operating the shift lever.
If the clutch pedal is not fully depressed before
the transmission is shifted, a gear noise may be
heard. Transmission damage could occur.
Start the vehicle in 1st gear and shift to 2nd, 3rd
and 4th up to 5th gear in sequence according to
the vehicle speed.
You cannot shift directly from 5th gear into
Reverse. First shift into the Neutral position, then
into Reverse.
If it is difficult to move the shift lever into Reverse
or 1st, shift to Neutral, then release the clutch
pedal. Fully depress the clutch pedal again and
shift into Reverse or 1st. If your vehicle is
equipped with four wheel drive, see “Using four
wheel drive” later in this section.
Suggested up-shift speedsThe table below provides suggested speed
ranges for shifting into a higher gear. These
suggestions relate to fuel economy and vehicle
performance. Actual shift ranges should be ad-
justed for specific road conditions, weather con-
ditions and individual driving habits.
Two wheel drive models and four wheel drive
models (2H and 4H position)
MPH (km/h)
1st to 2nd 15 (24)
2nd to 3rd 25 (40)
3rd to 4th 40 (64)
4th to 5th 45 (72)

Four wheel drive model (4L position)
MPH (km/h)
1st to 2nd 8 (13)
2nd to 3rd 12 (20)
3rd to 4th 20 (32)
4th to 5th 22 (36)
Suggested maximum speed in each
gearDownshift to a lower gear if the engine is not
running smoothly, or if you need to accelerate.
Do not exceed the maximum suggested speed
(shown below) in any gear. For level road driving,
use the highest gear suggested for that speed.
Always observe posted speed limits, and drive
according to the road conditions which will
ensure safe operation. Do not overrev the engine
when shifting to a lower gear as it may cause
engine damage or loss of vehicle control.
SSD0107
5-16
Starting and driving


04.3.9/R50-D/V5


Allowable maximum speed in each gear
Two wheel drive models and four wheel drive
models (2H position) MPH (km/h)
1st 22 (36)
2nd 37 (60)
3rd 56 (90)
4th & 5th — (—)
Four wheel drive models MPH (km/h)
4H position
1st 22 (36)
2nd 37 (60)
3rd 50 (80)
4th & 5th 50 (80)
4L position
1st 9 (15)
2nd 19 (30)
3rd 28 (45)
4th & 5th 31 (50)
CAUTION

Do not rest your foot on the clutch
pedal while driving. This may cause
clutch damage.

Fully depress the clutch pedal before
shifting to help prevent transmissiondamage.

Stop your vehicle completely before
shifting into R (Reverse).

When the vehicle is stopped for a
period of time, for example at a stop
light, shift to N(Neutral) and release
the clutch pedal with the foot brake
applied.
To apply:pull the lever up.
To release:
1. Firmly apply foot brake.
2.Manual transmission models:
Place the gearshift lever in the N (Neutral)
position.
Automatic transmission models:
Move the selector lever to the P (Park) posi-
tion.
3. While pulling up on the lever slightly, push
the button and lower completely.
PD1001M
PARKING BRAKE
Starting and driving
5-17


04.3.9/R50-D/V5