2004 MITSUBISHI L200 roof

GENERAL INFORMATION
Modification / alterations
to the electrical or fuel
systems
EB11A-D
MITSUBISHI has always manufactured
safe, high quality vehicles. In order to
maintain this safety and quality, it is impor-
tant that any accessory that is to be fitted,
or any modifications that are to be carried
out which involve the electric or fuel sys-
tems, should be carried out in accordance
with MITSUBISHI guidelines.
CAUTIONPlease consult an authorized MIT-
SUBISHI dealer concerning any
such fitment or modification.
If the wires interfere with the vehicle
body or if improper installation
methods are used (protective fuses
not included, etc.), electronic de-
vices may be adversely affected, re-
sulting in fire or an other accident.
Roof drip moulding*EB10A-Fb
When installing the roof rack, use the
brackets (A).
There are brackets (A) under roof drip
moulding (B).
NOTE
(1) Use a genuine MITSUBISHI roof car-
rier, since the brackets to be used are
of special shape. For details, consult
a nearby authorized MITSUBISHI
dealer.
(2) For the roof load, refer to page 10-6,
10-12, 10-19.
Roof carrier precaution
EB10A-S
CAUTION(1) Make sure that the weight of the
luggage does not exceed the al-
lowable roof load.
If the allowable roof load is ex-
ceeded, this may cause damage
to the vehicle.
The roof load is the total allow-
able load on the roof (the weight
of the roof carrier plus the
weight of luggage placed on the
roof carrier).
For specific figures, please refer
to the “Maximum roof load” on
page 10-6, 10-12, 10-19.
B10A013
AB
1-15
01engL2_240082_4 22-01-2004 12:58 Page 1-15

GENERAL INFORMATION
CAUTION(2) When luggage is loaded onto
the vehicle, please make sure to
drive slowly and avoid exces-
sive manoeuvres such as sud-
den braking or quick turning.
In addition, place the luggage on
the carrier so that its weight is
distributed evenly with the heav-
iest items on the bottom. Do not
load items that are wider than
the roof carrier.
The additional weight on the
roof could heighten the vehi-
cle’s centre of gravity and affect
the vehicle's handling charac-
teristics.
As a result, driving errors or
emergency manoeuvres could
lead to loss of control and result
in an accident.
(3) Before driving and after travel-
ling a short distance, always
check the load to make sure it is
securely fastened to the roof
carrier. Check periodically dur-
ing your travel that the load re-
mains secure. If the load is not
secure, it could fall from the ve-
hicle and damage your vehicle,
another vehicle or create road
hazard.
Genuine partsEB05A-Fi
Don’t play around with substitutes.
MITSUBISHI has gone to great lengths to
bring you a superbly crafted vehicle offer-
ing the highest quality and dependability.
Don’t reduce that quality and dependability
by using substitute parts.
Always use MITSUBISHI Genuine Parts
designed and manufactured to maintain
your MITSUBISHI vehicle at top perform-
ance. The operation of vehicle compo-
nents can be less efficient in case of using
Non-Genuine Parts.
Failure to use Genuine Parts, may in-
validate any future warranty claim.
MITSUBISHI will not be liable for any mal-
function of your vehicle that may have
been caused by the use of substitute parts
in place of MITSUBISHI Genuine Parts.
At the MITSUBISHI dealer you can also
get appropriate advise and the assem-
bling of Genuine Parts will be handled pro-
fessionally.
MITSUBISHI Genuine Parts are identified
by this mark, and are available at all au-
thorized MITSUBISHI dealers. NOTE
(1) To prevent wind noise or reduction in
gas mileage, remove the roof carrier
when not in use.
(2) Before using an automatic car wash,
check with the attendant to determine
if the roof carrier should be removed.
1-16
01engL2_240082_4 22-01-2004 12:58 Page 1-16

SEAT AND SEAT BELTS
3-27 The front air bags ARE DESIGNED NOT TO DEPLOY
when...
The front air bags are not designed to deploy in conditions where
they cannot typically provide protection to the occupant.
Such conditions are shown in the illustration:
1 - Rear end collisions
2 - Side collisions
3 - Vehicle rolls onto its side or roof
Because the front air bags do not protect the occupant in all types
of frontal collisions, be sure to always properly wear your seat
belts.
G28L127
123

03engL2_240082_4 22-01-2004 13:01 Page 3-27

STARTING AND DRIVING
5-7
(1)Starting
Avoid rapid acceleration and sudden
starts; such operation will result in
higher fuel consumption.
(2)Shifting
Shift only at an appropriate engine
speed. Always use the highest gear
possible.
The transfer shift lever should be set
to “2H” when driving 4WD vehicles on
normal roads and express ways to
obtain best possible fuel economy.
(3)City traffic
Frequent starting and stopping in-
creases the average fuel consump-
tion. Use roads with smooth traffic
flow whenever possible. When driving
on congested roads, avoid use of a
low gear at high engine speeds.
(4)Idling
The vehicle consumes fuel even dur-
ing idling. Avoid extended idling
whenever possible.
(5)Speed
The higher the vehicle speed, the
more fuel consumed. Avoid driving at
full speed. Even a slight release of the
accelerator pedal will save a signific-
ant amount of fuel.Trailer towingEC21APDd
In order to tow a trailer with your vehicle,
have a trailer towing device that meets all
pertinent regulations in your area mount-
ed at an authorized MITSUBISHI dealer.
The regulations concerning the towing of
a trailer may differ from country to country.
It is recommended that you obey the regu-
lations in each area.
CAUTIONDanger of Accident!
A towing bar should be fitted by an
authorized MITSUBISHI dealer.
NOTE
Fitting of a towing bar requires specialized
skills and equipment.
Contact an authorized MITSUBISHI dealer
for details. If you are going to tow a trailer,
pay careful attention to the following
points.
(6)Tyre inflation pressure
Check the tyre inflation pressures at
regular intervals. Low tyre inflation
pressure increases road resistance
and fuel consumption. In addition, low
tyre pressures adversely affect tyre
wear and driving stability.
(7)Load
Do not drive with unnecessary articles
in the luggage compartment. Espe-
cially during city driving where fre-
quent starting and stopping is ne-
cessary, the increased weight of the
vehicle will greatly affect fuel con-
sumption. Also avoid driving with un-
necessary luggage, etc., on the roof;
the increased air resistance will in-
crease more fuel consumption.
(8)Cold engine starting
Starting of a cold engine consumes
more fuel.
Unnecessary fuel consumption is also
caused by keeping a hot engine run-
ning. After the engine is started, com-
mence driving as soon as possible.
(9)Air conditioning*
The use of the air conditioning will in-
crease the fuel consumption.
05engL2_240082_4 22-01-2004 13:04 Page 5-7

STARTING AND DRIVING
5-28 Climbing sharp grades
Set the transfer shift lever to “4L” to max-
imize the engine torque.
WARNING(1) Go straight up. Do not try to
traverse across a steep slope.
(2) If you begin to lose traction,
ease off the accelerator pedal
and gently turn the steering
wheel alternately left and right to
regain adequate traction again.
NOTE
(1) Choose as smooth a slope as possi-
ble with few stones or other obsta-
cles.
(2) The climbing ability is approximate
35° grade on dry pavement.
(3) Before attempting to drive up the
slope, walk up it to confirm that the
vehicle can handle the gradient.
Descending sharp grades
Set the transfer shift lever to “4L”, use the
engine brake (downshifting) and descend
slowly.
WARNINGAvoid snaking down a sharp gra-
dient. Descend the grade as straight
as possible.
NOTE
(1) When descending a sharp grade, if the
brakes are applied suddenly because
of an obstacle encountered, control of
the vehicle could be lost. Before de-
scending the slope, walk down it and
confirm the path.
(2) Before descending a grade, it is neces-
sary to choose the appropriate gear.
Avoid changing gears or depressing the
clutch while descending the grade.
(3) MITSUBISHI is not responsible to the
operator for any damage or injury
caused or liability incurred by the im-
proper and negligent operation of a ve-
hicle. All techniques of vehicle opera-
tion described herein depend on the
skill and experience of the operator
and other participating parties, and any
deviation from the recommended oper-
ating instructions above is at their own
risk.
Turning sharp corners
When turning a sharp corner in “4H” or
“4L” position at low speed, a slight differ-
ence in steering may be experienced
similar to as if the brakes were applied.
This is called tight corner braking and
results from each of the four tyres being at
a different distance from the corner.
The phenomenon is peculiar to 4-wheel
drive vehicles. If this occurs, either
straighten the steering wheel, or change
to rear-wheel drive.
Crossing a stream (fording)
4-wheel drive vehicles are not necessarily
waterproof. If the electrical circuits be-
come wet, further operation of the vehicle
will be impossible; therefore, avoid cross-
ing streams unless absolutely necessary.
If crossing a stream is unavoidable, use
the following procedure:
(1) Check depths of a stream and geo-
graphical features before attempting
to cross a stream and ford the stream
where the water is as shallow as prac-
ticable.
(2) Set the transfer shift lever to “4L”.
(3) Drive slowly at a speed of approxi-
mately 5 km/h (3 mph) to avoid
splashing too much water.
05engL2_240082_4 22-01-2004 13:05 Page 5-28

FOR PLEASANT DRIVING
Pillar antennaEH11D-Cd
When listen to the radio, fully extend the
antenna. Before entering an automatic car
wash or other low-roofed area, be sure to
retract the antenna.
NOTE
Be sure to put down the pillar antenna in
the following cases:
• When entering a place with low clear-
ance.
• When going into an automatic car wash.
• When placing a car cover over the
vehicle.
VentilatorsEH16AAGf
1 - Centre ventilators
2 - Side ventilators
Air flow and direction adjustments
3 - Knob
4 - Ventilator dial
Ventilator dial
The ventilator can be opened and closed
with the dials.
- Open
- Close
Knob
Adjust the direction of the air flow by mov-
ing the knob.
6-18
H11D045H16A118
1
2
2
H16A324
3Centre ventilators
06engL2_240082_4 22-01-2004 13:07 Page 6-18

SPECIFICATIONS
Weights EP01DPS
NOTE
Trailer specifications indicate the manufacturer’s recommendation.
10-19

Item
2WD4WD
With turbochargerWithout
turbo-
chargerWithout catalytic converterWith catalytic converter
GLGLSGLGLXGLS
A/TM/TA/TM/TA/TM/TA/TM/TA/TM/T
Kerb weight

1,525 kg 1,515 kg 1,475 kg 1,735 kg 1,730 kg 1,755 kg 1,750 kg 1,750 kg 1,745 kg 1,745 kg 1,770 kg 1,765 kg

Maximum gross vehicle weight
2,570 kg 2,830 kg
Maximum axle
weightFront
1,000 kg 1,200 kg
Rear
1,700 kg 1,800 kg 1,750 kg 1,800 kg 1,800 kg 1,750 kg
Maximum trailer
weightWith brake
1,800 kg2,700 kg
Without brake
500 kg
Maximum trailer-nose weight
75 kg 100 kg
Maximum roof load
50 kg
Seating capacity
(including a driver)5 persons
10engL2_240082_4 22-01-2004 13:14 Page 10-19

INDEX
Gauges ........................................................ 4-3
Genuine parts ............................................ 1-15
Glove box .................................................. 6-35
Hazard warning flasher switch .................. 4-18
Hazard warning indication lamp .................. 4-7
Headlamp
Headlamp levelling switch ...................... 4-14
Headlamps
Headlamps, Dipper, Passing .................. 4-12
Replacement ........................................... 8-35
Washer switch......................................... 4-17
Head restraints ............................................ 3-5
Heated seats ............................................... 3-7
Heater/Air conditioning .............................. 6-19
High-beam indication lamp .......................... 4-7
Hinges and latches lubrication................... 9-16
Horn switch ................................................ 4-20
Ignition switch .............................................. 5-9
Inclinometer ................................................. 4-4
Indication and warning lamps ...................... 4-6
Inside rear-view mirror ............................... 5-37
Installation of accessories ......................... 1-13
Instruments .................................................. 4-2
Jack ............................................................. 8-5
Jack handle ................................................. 8-7
Jacking up the vehicle ................................. 8-8
Jump starting (Emergency starting) .......... 8-27
Keyless entry system................................... 2-5
Keys............................................................. 2-2Leakage (Fuel, engine coolant,
oil and exhaust gas) ................................ 9-14
Light
Bulb capacity........................................... 8-34
Headlamps .............................................. 4-12
Room lamps ............................................ 4-20
Limited-slip differential ............................... 5-35
Low fuel indication lamp .............................. 4-7
Manual transmission
Driving speed .......................................... 5-14
Shifting .................................................... 5-14
Manual window control ................................ 2-9
Meter, gauge and indication/warning
lamp operation ........................................ 9-14
Meter illumination control........................... 4-20
Mirrors
Day/Night Type inside rear-view mirror .. 5-37
Electric remote-controlled
outside rear-view mirrors ...................... 5-38
Vanity mirror............................................ 6-32
Octane rating ............................................... 5-3
Odometer/Tripmeter .................................... 4-3
Oil pressure warning lamp ........................... 4-9
Oil
Engine oil ....................................... 9-2, 10-26
Manual transmission oil ........................ 10-26
Operation under adverse
driving conditions ...................................... 8-2
Overheating (Engine) ................................ 8-23Parking ............................................. 5-20, 5-32
Parking brake ............................................ 5-30
Performance ....................... 10-5, 10-11, 10-18
Pillar antenna............................................. 6-18
Polishing ...................................................... 7-6
Power steering
Fluid ............................................... 9-9, 10-26
System .................................................... 5-37
Pregnant women restraint ......................... 3-20
Punctured .................................................. 8-16
Quarter window ......................................... 2-11
Rear differential lock .................................. 5-23
Rear fog lamp switch ................................. 4-19
Rear gate ................................................... 2-12
Rear heater................................................ 6-30
Rear seat ..................................................... 3-5
Rear secret box ......................................... 6-37
Rear window demister switch .................... 4-18
Rear-view mirrors ...................................... 5-37
Removal of water from the fuel filter
(diesel-powered vehicles only) ............... 8-26
Replacement of lamp bulbs ....................... 8-34
Front turn-signal and position lamps ....... 8-36
Headlamps .............................................. 8-35
High-mounted stop lamps ....................... 8-38
Side turn-signal lamps ............................ 8-36
Number-plate lamps ............................... 8-37
Rear combination lamps ......................... 8-37
Rear fog lamps........................................ 8-38
Rheostat .................................................... 4-20
Roof drip moulding .................................... 1-14
Room lamps .............................................. 4-20
10-28
10engL2_240082_4 22-01-2004 13:14 Page 10-28