2004 MITSUBISHI L200 engine

INSTRUMENTS AND CONTROLS
4-12
Combination headlamps,
dipper and turn signal
switch
EE11AAMb
Headlamps
Rotate the switch to turn on the lamps.
- All lamps off
- Position, tail, licence-plate, and in-
strument panel lamps on
- Headlamps on and other lamps go
on
NOTE
[Vehicles with Dim Dip]
When the ignition key is in the “ON” posi-
tion and the lamp switch is set to the
“ ” position, the low beam of the head-
lamp will illuminate dimly.
Dipper (High/Low beam change)
EE11B-Dd
When the lamp switch is in the “ ” posi-
tion, the beam changes from high to low
(or low to high) each time the lever is
pulled to (1). While the high beam is on,
the high beam indication lamp in the in-
strument cluster will also illuminate.
[Vehicles with Daytime Running Lamp]
When the ignition key is in the “ON” posi-
tion and the lamp switch is set to the “ ”
position, the low beam of the headlamps,
tail lamps, etc., will illuminate.
Lamp monitor system
If the driver’s door is opened when the key
is in the “LOCK” or “ACC” position or re-
moved from the ignition switch with the
lamp switch in the “ ” or “ ” position,
a buzzer will sound to remind the driver to
turn off the lamps.
Turn of the lamp switch, and the buzzer
will stop.
NOTE
(1) Do not leave the headlamps and
other lamps on for too long while the
engine is stationary. A run-down bat-
tery could result.
(2) When it rains, or when the vehicle has
been washed, the inside of the lens
sometimes becomes foggy. This is the
same phenomenon as when window
glass mists up on a humid day, and
does not indicate a functional prob-
lem. When the lamp is switched on,
the heat will remove the fog. However,
if water gathers inside the lamp,
please go to an authorized MIT-
SUBISHI dealer for a check.
E11A015E11C013
12
04engL2_240082_4 22-01-2004 13:20 Page 4-12

INSTRUMENTS AND CONTROLS
4-18
Hazard warning flasher
switch
EE16A-Dd
Use the hazard warning flasher switch
when the vehicle has to be parked on the
road for any emergency.
The hazard warning flashers can always
be operated, regardless of the position of
the ignition key.
Push the switch to turn on the hazard
warning flashers; push the switch again to
turn them off.
When this switch is operated, all turn-sig-
nal lamps flash continuously, as do the
turn-signal indication lamps in the instru-
ment cluster.
Rear window demister
switch*
EE17ABAa
The rear window demister switch can be
operated with the ignition switch in the
“ON” position.
Push the switch to turn on the rear window
demister.
To turn off the demister, press the switch
once again.
If your vehicle is equipped with the rear
window demister timer, this will be turned
off automatically in about 11 minutes.
To turn off the demister within 11 minutes,
push the switch again.
The indication lamp (A) will illuminate
while the demister is on.
If your vehicle is equipped with heated
mirrors, these operate in conjunction with
the demister.
CAUTION
If the lamps are kept flashing for a
long time, the battery will be dis-
charged, resulting in hard engine
starting or a no starting at all.
E17A025
A
E16A026
04engL2_240082_4 22-01-2004 13:20 Page 4-18

INSTRUMENTS AND CONTROLS
4-19
Refer to “Electric remote-controlled out-
side rear-view mirrors” on page 5-38.
CAUTION(1) The demister switch is not for
melting snow but for cleaning
mist. Remove snow before us-
ing the demister switch.
(2) To avoid unnecessary battery
discharge, do not use the rear
window demister during starting
of the engine or when the engine
is not running. Turn the demist-
er off immediately after the win-
dow is clear.
(3) When cleaning the inside of the
rear window, use a soft cloth
and wipe gently along the heater
wires, being careful not to dam-
age the wires.
(4) Do not allow objects to touch
the inside of the rear window
glass, damaged or broken wires
may result.
Rear fog lamp switch*EE08B-Ma
The rear fog lamp can only be operated
when the headlamps turn on.
1 - Rear fog lamp on.
2 - Rear fog lamp off.
The indication lamp in the instrument clus-
ter will illuminate while the rear fog lamp is
on.NOTE
(1) The rear fog lamp is automatically
turned off when the headlamp is
turned off.
(2) In case of vehicles with Daytime Run-
ning Lamp, the front fog lamp can be
operated even if the lamp switch is set
to the “ ” (OFF) position, because
the low beam of the headlamps, tail
lamps, etc. illuminate when the igni-
tion key is at the “ON” position.
(3) The rear fog lamp is installed only on
the driver’s side.
E08B037
2 1
Type 2
E08B020
1
2
Type 1
04engL2_240082_4 22-01-2004 13:20 Page 4-19

INSTRUMENTS AND CONTROLS
4-21
[Vehicles with keyless entry system]
The room lamp goes on when a door
is opened. When all doors are closed,
the room lamp is illuminated and
dimmed gradually for 30 seconds
then goes out.
However, the lamp goes out immedi-
ately without being dimmed in case of
the followings:
• The ignition switch is turned “ON”.
• All doors are locked using the key
mechanism of the driver’s door, the
lock knob of the driver’s door, or the
remote control switch of the keyless
entry system.NOTE
If the ignition key is removed with the
doors closed, the room lamp is dimmed
gradually for 30 seconds and then goes
out.
3 (ON) -The lamp illuminates.Personal lamps*
Push the button to turn on the lamp. Push
it again to turn it off.
NOTE
If you leave the lamps on without running
the engine, you will run down the battery.
Before you leave the vehicle, make sure
that all the lamps are off.
E19A058E19A052
1
2
3
Club cab, Double cab
04engL2_240082_4 22-01-2004 13:20 Page 4-21

Vehicles with automatic transmission
2WD
*1with overdrive switched OFF
*2with overdrive switched ON
4WD
*1with overdrive switched OFF
*2with overdrive switched ON
STARTING AND DRIVING
Running-in
recommendations
EA01APD
During the running-in period for the first
1,000 km, it is advisable to drive your new
vehicle using the following precautions as
a guideline to aid long life as well as future
economy and performance.
(1) Do not race the engine at high speeds.
(2) Avoid rapid starting, accelerating,
braking and prolonged high-speed
running.
(3) Keep to the running-in speed limit
shown below.
Please note that the legal speed limits
displayed must be adhered to.
(4) Do not exceed loading capacity.
(5) Refrain from towing a trailer.
Vehicles with manual transmission
2WD4WD
Petrol-powered vehicles
Diesel-powered vehicles
5-2
Drive rangeSpeed limit km/h (mph)
With
turbochargerWithout
turbocharger
1st 20 (12) 20 (12)
2nd 40 (24) 35 (21)
3rd 65 (40) 55 (34)
4th 85 (52) 85 (52)
5th 100 (62) 105 (65)

Drive range
Speed limit km/h (mph)
2H, 4H4L
1st 25 (15) 10 (6)
2nd 50 (31) 25 (15)
3rd 75 (46) 40 (24)
4th 105 (65) 55 (34)
5th 125 (77) 65 (40)

Drive range
Speed limit km/h (mph)

“L” (LOW)

25 (15)
“2” (SECOND)

50 (31)
“D” (DRIVE)

75 (46)*
1

105 (65)*
2
Drive
range
Speed limit km/h (mph)
Vehicles with
205/80R16
tyre sizeVehicles with
265/70R16
tyre size
2H, 4H4L2H, 4H4L
“L”
(LOW)30 (18) 15 (9) 30 (18) 15 (9)
“2”
(SECOND)55 (34) 30 (18) 60 (37) 30 (18)
“D”
(DRIVE)85 (52)*1
125 (77)*245 (27)*1
65 (40)*285 (52)*1
125 (77)*245 (27)*1
65 (40)*2

Drive
range
Speed limit km/h (mph)
Vehicles with
205/80R16 tyre size
Vehicles with
265/70R16 tyre size
2H, 4H4L2H, 4H4L

1st20 (12) 10 (6) 20 (12) 10 (6)
2nd35 (21) 20 (12) 40 (24) 20 (12)
3rd60 (37) 30 (18) 65 (40) 30 (18)
4th85 (52) 45 (27) 90 (55) 45 (27)
5th105 (65) 55 (34) 110 (68) 55 (34)
05engL2_240082_4 22-01-2004 13:04 Page 5-2

STARTING AND DRIVING
Fuel selectionEC20CPF
CAUTIONFor diesel-powered vehicles, fuel ad-
ditives can cause ignition compo-
nents to be damaged and never use
the fuel additives.1. Before filling with fuel, stop the en-
gine.
2. The fuel tank filler is located on the
rear left side of your vehicle.
Type 1
The fuel tank filler door can be opened
from inside the vehicle by using the fuel
tank filler door release lever located be-
side the driver’s seat.
Filling the fuel tankEC20DPF
CAUTIONGasoline is highly flammable and ex-
plosive. You could be burned or seri-
ously injured when handling it.
When refuelling your vehicle, always
turn the engine off and keep away
from flames, sparks and smoking
materials. Always handle fuel in
well-ventilated outdoor areas.
Fuel tank capacity
2WD : 69 litres
4WD : 75 litres
5-3
Recommended
fuel
Petrol-powered vehicles
Unleaded petrol octane rating
(DIN 51607)
91 RON or higher (Normal)
Diesel-powered vehicles
Cetane rating (DIN 51601)
45 or higher
C20A042
Type 1
05engL2_240082_4 22-01-2004 13:04 Page 5-3

STARTING AND DRIVING
6. To close, turn the fuel tank filler tube
cap slowly clockwise until you hear
clicking sounds, then gently push the
fuel tank filler door closed.
CAUTIONIf you need to replace the fuel tank
filler tube cap, use only the cap
specified for your model vehicle.
CAUTIONDamage to the catalytic converter
can result if your vehicle is not kept
in proper operating condition. In the
event of an engine malfunction par-
ticularly involving engine misfire or
other apparent loss of performance
have your vehicle serviced prompt-
ly. Continued operation of your
vehicle with a severe overheated
condition may result in possible
damage to the converter and
vehicle.
WARNING(1) As with any vehicle, do not park
or operate this vehicle in areas
where combustible materials
such as dry grass or leaves can
come in contact with a hot
exhaust since a fire could occur.
(2) Undercoating paint should not
be applied to the catalytic con-
verter.
Catalytic converter*EC18A-Pa
In case of the petrol-powered vehicles, for
ordinary use, there are no particular pre-
cautions except that of using unleaded
petrol.
The exhaust gas scavenging device with
catalytic converter is extremely efficient
for the reduction of noxious gases. The
catalytic converter is installed in the ex-
haust system.
It is important to keep the engine properly
tuned to ensure proper catalyst operation
and prevent possible catalyst damage.
5-5
C18A001
05engL2_240082_4 22-01-2004 13:04 Page 5-5

STARTING AND DRIVING
5-6
The catalytic converter itself gets hot
quickly, and may be damaged if overheat-
ed. The following points should be noted
in order to prevent the ignition of unburned
petrol within the catalytic converter.
(1) In case of the petrol-powered vehi-
cles, use UNLEADED PETROL
ONLY of the type of recommended in
“Fuel selection” on page 5-3.
(2) Do not drive with an extremely low
fuel level; running out of fuel could
cause damage to the catalytic con-
verter.
(3) Do not switch OFF the ignition switch
while driving.
(4) Do not try to start the engine by push-
ing the vehicle. If the battery is weak
or discharged, use another battery to
start the engine.
(5) In case of the petrol-powered vehi-
cles, do not idle the engine with any
spark plug wires disconnected or re-
moved such as performing diagnostic
tests.
(6) Do not idle the engine for prolonged
periods during very rough idle or mal-
functioning operating conditions.
(7) Do not race the engine when turning
off the ignition switch to prevent cat-
alytic converter from being damaged
due to unburnt fuel.(8) Stop driving the vehicle if you think
the performance is noticeably low, or
that there is unnecessary engine rota-
tion, or any other engine trouble, such
as with the ignition, etc.
If it is impractical to stop driving imme-
diately, reduce the speed and drive
for only a short time. Have an inspec-
tion made by your nearest authorized
MITSUBISHI dealer as soon as pos-
sible.
(9) In unusual situations involving grossly
malfunctioning engine operation, a
burnt smell may indicate severe and
abnormal catalyst overheating.
If this occurs, the vehicle should be
stopped in a safe place, the engine
switched off and the vehicle allowed
to cool. Once the engine is cool, a
service, including a tune-up to manu-
facturer’s specifications, should be
obtained immediately.Economical drivingEC19AAPa
For economical driving, there are some
technical requirements that have to be
met. The prerequisite for low fuel con-
sumption is a properly adjusted engine. In
order to achieve longer life of the vehicle
and the most economical operation, have
the vehicle serviced by an authorized
MITSUBISHI dealer at regular intervals in
accordance with the service standards.
Fuel economy and generation of exhaust
gas and noise are highly influenced by
personal driving habits as well as the par-
ticular operating conditions. The following
points should be observed in order to min-
imize wear of brakes, tyres and engine as
well as to reduce environmental pollution.
05engL2_240082_4 22-01-2004 13:04 Page 5-6