2004 MITSUBISHI L200 page 20

FOR PLEASANT DRIVING
To listen to the radioEH30BPD
1 - PWR (On-off switch)
2 - VOL (Volume control)
3 - BASS (Bass tone control)/
(PULL) TREB (Treble tone control)
4 - BAL (Left/right balance control)/
(PULL)FADE (Front/rear balance control)*
5 - UML (UKW/MW/LW selection) button
6 - TUNE/SEEK/DISC (Down-step/Down-seek) button
7 - TUNE/SEEK/DISC (Up-step/Up-seek) button
8 - Memory select buttons
9 - Frequency display/Tape travel display window
10 - Preset memory number display
11 - ST (Stereo indicator)
*: Vehicle with 4 speakers only
6-3
H11A341
1,2
3456 7 891011
06engL2_240082_4 22-01-2004 13:07 Page 6-3

FOR PLEASANT DRIVING
1. Press the PWR switch (1) to turn on
the radio.
Press the PWR switch again to switch
it off.
2. Press the UML button (5) to select the
desired band (UKW/MW/LW).
3. Press the TUNE/SEEK button (6 or 7)
or one of the Memory select buttons
(8) to tune to a station.
Refer to “How to adjust the tune” or
“How to enter frequencies in the
memory”.
How to adjust the volume and tone
VOL (Volume control) - 2
Turn the knob clockwise to increase the
volume.
BASS (Bass tone control) - 3
Press the button, and it will pop-up. Rotate
the knob clockwise or counterclockwise to
select the desired bass tone quality.
TREB (Treble tone control) - 3
Press the button, and it will pop-up. Pull
and rotate the knob clockwise or counter-
clockwise to select the desired treble tone
quality.BAL (Left/right balance control) - 4
Press the button, and it will pop-up. Rotate
the knob in either direction to balance the
volume of sound from the left and right
speakers.
FADE (Front/rear balance control)* - 4
Press the button, and it will pop-up. Pull
and turn the knob to the left or right to bal-
ance the volume of the front and rear
speakers.
NOTE
(1) The BASS (3), TREB (3), BAL (4),
and FADE (4) buttons should be ad-
justed after they have been popped
out. After adjusting, keep them
pressed in.
(2) In a two-speaker vehicle, keep the
FADE (front/rear balance control) set-
ting in the middle position. Since no
rear speakers are connected, adjust-
ing the FADE setting towards the “R”
(rear) side could result in a loss of
sound output.
How to adjust the tune
Automatic tuning
After keeping the TUNE/SEEK button
(6 or 7) depressed for more than 1 sec-
ond, remove your fingers from the button,
and reception of a receivable station will
start.
Manual tuning
The frequency changes every time the
TUNE/SEEK button (6 or 7) is pressed.
Press the button to select the desired sta-
tion.
6-4
06engL2_240082_4 22-01-2004 13:07 Page 6-4

FOR PLEASANT DRIVING
How to enter frequencies in the
memory
As many as 12 UKW, 6 MW and 6 LW sta-
tion frequencies can be entered in the
memory.
Follow the steps described below.
1. Press either the TUNE/SEEK button
(6 or 7) to tune the frequency to be
entered in the memory.2. Press one of the Memory select but-
tons (8) until it beeps. The sound will
be momentarily interrupted while the
frequency is being entered into the
memory. The number of the button
corresponding to the entry into the
memory, and the frequency are dis-
played.
3. The preset memory setting is re-
trieved by pressing the button and
then releasing it within 2 seconds.
NOTE
Disconnecting the battery terminal
erases all frequencies stored in the
memory.
6-5
H11A197
06engL2_240082_4 22-01-2004 13:07 Page 6-5

FOR PLEASANT DRIVING
Radio data system (RDS)EH30C-Ea
1 - PTY (Program type) button
2 - TP (Traffic program) button
3 - UM/ (UKW/MW/LW selection) button
4 - TUNE/SEEK (Down-step/Down-seek) button
5 - TUNE/SEEK (Up-step/Up-seek) button
6 - Memory select buttons
7 - Frequency display
8 - PTY (Program type) indicator
9 - RDS (Radio data system) indicator
10 - TP (Traffic program) indicator
11 - AF (automatic retuning function) indicator
12 - REG (Regional program) indicator
6-6
H11A342
12
34 5 6789101112
06engL2_240082_4 22-01-2004 13:07 Page 6-6

FOR PLEASANT DRIVING
RDS uses PI (program identification) sig-
nal and AF(alternative frequency) list
transmitted in addition to the normal UKW
broadcasting programs, and pick up the
UKW stations that are transmitting the
same program from the EON (enhanced
other network) and automatically tunes
to the station with the strongest signal
intensity.
Therefore, you can continue listening to
one program in, for example, a long dis-
tance driving without returning to other
station transmitting the same program
when you are leaving the service area of
the currently receiving station.
The RDS radio also features the limited
reception of the program types, the break-
in reception of the traffic announcement
and emergency broadcast, and the lim-
ited/unlimited reception of the regional
programs.PTY (Program type)
RDS broadcasts are classified according
to program type (PTY) as follows. Use the
TUNE/SEEK button (4 or 5) to select your
desired PTY.
1. SPEECH
2. NEWS
3. AFFAIRS
4. INFO (Information)
5. SPORT
6. EDUCATE (Education)
7. DRAMA
8. CULTURE
9. SCIENCE
10. VARIED
11. MUSIC
12. POP M
13. ROCK M
14. M.O.R.M. (Middle of road music)
15. LIGHT M (Light/classic)
16. CLASSIC
17. OTHER M (Other music)
NOTE
If “1” or “11” is selected, the program
search is made widely under the category
of speech or music.Automatic retuning function
The automatic retuning function finds sta-
tions that are broadcasting the same pro-
gram and automatically tunes to the sta-
tion with the strongest signal.
Press the UML button (3) for more than 2
seconds, and the AF indicator (11) will illu-
minate in display (7). Press the UML but-
ton for more than 2 seconds again to re-
set.
PI (Program identification)
When listening to stations programmed
into the Memory select buttons (6), you
may listen to broadcasts with the same PI.
If the very same station as memorized
cannot be received, a station broadcast-
ing the same program in the same net-
work is automatically selected. The dis-
play (7) will then show the REG indicator
(12).
6-7
06engL2_240082_4 22-01-2004 13:07 Page 6-7

FOR PLEASANT DRIVING
To search for a broadcast of desired pro-
gram type:
1. Press the PTY button (1)
2. Press the TUNE/SEEK button (4 or 5)
for less than 1 second at a time to se-
lect your desired PTY.
3. Two seconds after a desired PTY has
been selected, the radio will begin to
search for a broadcast of your se-
lected PTY.
During search, “PTY” on the display
blinks, and the radio will begin to
search for a broadcast of your se-
lected PTY.
4. When the radio picks up a station with
your desired PTY, the display will
show the name of the station.NOTE
(1) If the TUNE/SEEK button (4 or 5) is
pressed for more than 1 second, the
radio will try to find out another broad-
cast of the same program type as cur-
rently selected.
(2) If no station is found with your desired
PTY, the display will show “EMPTy”
for around 5 seconds, and the radio
will return to the previous station.How to enter PTYs in the memory
As many as 6 PTYs can be entered in the
memory.
Follow the steps described below.
1. Press either the TUNE/SEEK button
(4 or 5) to tune the PTY to be entered
in the memory.
2. Press one of the Memory select but-
tons (6) until it beeps. The sound will
be momentarily interrupted while the
PTY is being entered into the mem-
ory. The number of the button corre-
sponding to the entry into the mem-
ory, and the PTY are displayed.
3. The preset memory setting is re-
trieved by pressing the button and
then releasing it within 2 seconds.
NOTE
Disconnecting the battery terminal
erases all PTYs stored in the memory.Traffic information
The radio will automatically tune in to traf-
fic information broadcasts while receiving
UKW broadcasts, playing cassettes or
CD. To select this function, follow the in-
structions below:
1. Press the TP button (2). The display
will show “TP” (10). If the RDS data
can be read, the display will show
“RDS” (9). If not, the display will show
“NO RDS” for about 5 seconds.
6-8
H11A200H11A199
06engL2_240082_4 22-01-2004 13:07 Page 6-8

FOR PLEASANT DRIVING
2. If the radio detects traffic information
on either the station currently se-
lected or on another station, the dis-
play will show “TRAF INF” for 5 sec-
onds followed by a 2-second indica-
tion of the frequency. Then, it will
show the name of the station broad-
casting the traffic information to which
you will listen. If the volume level is
too low to hear the traffic information,
the radio will automatically optimize
the volume level. When the traffic in-
formation broadcast is over, the previ-
ously received program will be recov-
ered automatically.
3. Press the TP button (2) to return to
the previous condition.Emergency broadcasts
If an emergency broadcast is caught while
receiving a UKW broadcast or playing
back a cassette tape or CD with the igni-
tion switch in “ACC” or “ON” position, the
display will show “ALARM” and the emer-
gency broadcast will interrupt the current
program. If the volume level is too low to
hear the emergency broadcasts, the radio
will automatically optimize the volume
level. When the emergency broadcast is
over, the previously received program will
be recovered automatically.
6-9
H11A204
06engL2_240082_4 22-01-2004 13:07 Page 6-9

FOR PLEASANT DRIVING
To listen to a tapeEH30D-F
1 - Cassette eject button
2 - Cassette slot
3 - APS (Auto program sensor rewind) button
4 - APS (Auto program sensor forward) button
5 - (Fast rewind) button
6 - (Fast forward) button
7 - RPT (Repeat) button
8 - (Dolby noise reduction) button
9 - TAPE button
10 - (Tape direction selection) button
11 - Tape travel display window
12 - RPT (Repeat mode) indicator
13 - (Dolby noise reduction) indicator
6-10
H11A343
12
9103 4 5 6 7 8 11 12 13
06engL2_240082_4 22-01-2004 13:07 Page 6-10