2004 MITSUBISHI L200 ECO mode

SEAT AND SEAT BELTS
3-20
Pregnant women restraint
EG28C-Ad
WARNINGSafety belts work for everyone, in-
cluding pregnant women. Pregnant
women should use the available seat
belts. This will reduce the likelihood
of injury to both the woman and the
unborn child. The lap belt should be
worn across the thighs and as snug
against the hips as possible, but not
across the waist. The woman’s doc-
tor should be consulted if there are
any questions.
Seat belt inspectionEG28D-Ad
(1) Check the belts for cuts, worn or
frayed webbing and for cracked or de-
formed metallic parts. Replace the
belt assembly if defective.
(2) A dirty belt should be cleaned with
neutral detergent in warm water. After
rinsing in water, let it dry in the shade.
Do not attempt to bleach or re-dye the
belts because this affects their char-
acteristics.
WARNING(1) All seat belt assemblies includ-
ing retractors and attaching
hardware should be inspected
by an authorized MITSUBISHI
dealer after any collision. We
recommend that seat belt as-
semblies in use during a colli-
sion be replaced unless the col-
lision was minor and the belts
show no damage and continue
to operate properly.
(2) Do not attempt to repair or re-
place any part of the seat belt as-
semblies; this work should be
done by an authorized MITSU-
BISHI dealer. Failure to have an
authorized MITSUBISHI dealer
perform the work could reduce
the effectiveness of the belts
and could result in serious in-
jury in the event of a collision.
Supplemental restraint
system (SRS)-air bag*
EG08G-Mc
The information written in this supplemen-
tal restraint system (SRS) section con-
tains important points concerning the
driver and front passenger air bags.
The SRS air bag is designed to supple-
ment the primary protection of the driver
and front passenger side seat belt sys-
tems by providing those occupants with
protection against head and chest injuries
in certain moderate-to-severe frontal colli-
sions.
The SRS is NOT a substitute for the seat
belts; for maximum protection in all types
of crashes and accidents, seat belts
should ALWAYS be worn by everyone
who drives or rides in this vehicle. (With
infants and small children in child re-
straints and older children buckled in the
rear seat).
03engL2_240082_4 22-01-2004 13:01 Page 3-20

INSTRUMENTS AND CONTROLS
4-15
Double cab
*
1: Vehicles with heavy duty suspension
●: 1 person : Full luggage loading
Switch position 0-Driver only
Switch position 1-Driver + full luggage loading
Switch position 2-Driver + full luggage loading
Switch position 3-Driver + full luggage loading
Switch position 4-Driver + full luggage loading
Windscreen wiper and
washer switch
EE13A-Yc
The windscreen wiper and washer can be
operated with the ignition switch in the
“ON” or “ACC” position.
Move the switch to operate the wind-
screen wipers or spray the washer fluid.
Windscreen wipers
Type 1
- Off
- Intermittent operation at intervals of
approximately 4 seconds
- Slow
- Fast
Type 2
- Off
- Intermittent operation
- Slow
- Fast
E13A035
Type 1
E13A061
Type 2
Vehicle condition
Switch position

2WD “0” “4”, “3*
1

”
4WDExcept for
GLS (A/T)
models“0” “4”, “3*
1

”
GLS
(A/T) models“0” “3”, “2*
1

”
04engL2_240082_4 22-01-2004 13:20 Page 4-15

STARTING AND DRIVING
5-9
mm
*
1: Single cab, double cab
*2: Club cab
NOTE
The values under item 10 are applicable
to unladen vehicles. These values can
also be varied depending on the tyre size,
optional equipment and suspension con-
ditions.
Ignition switchEI01ABGa
1 - The engine is stopped, and the steer-
ing wheel locked. The key can only be
inserted and removed only when the
switch is in this position.
2 - The engine is stopped, but the radio,
cigarette lighter and other electrical
devices can be operated.
3 - The engine is running and all the vehi-
cle’s electrical devices can be oper-
ated.
4 - The starter motor operates. After the
engine has started, release the key
and it will automatically return to the
“ON” position.
Operating hints
(1) Do not let the clutch slip (vehicles with
a manual transmission only) and do
not increase the engine speed more
than necessary when starting.
(2) Be sure that the driving speed does
not exceed the maximum speed for
trailer operation.
(3) To prevent shocks from the overrun
brake, depress the brake pedal lightly
at first and then more strongly.
(4) To make full use of engine braking,
change to a lower gear before de-
scending a slope.
(5) The body, brakes, clutch, and chassis
will be under additional strain when
towing a trailer.
(6) The heavier weight and higher rolling
and air resistance will increase fuel
consumption.
Additional precautions for vehicles
equipped with an automatic transmission
It is recommended to use the “2” position
on slopes or at low speed. Use the “L” po-
sition in mountainous areas in order to
make better use of engine braking and to
assist the brake system. However, be sure
that the speed does not exceed the maxi-
mum speed limit for the selected gear.
For maximum speed, refer to the descrip-
tion of the “Possible driving speed” on
page 5-19.
2WD models4WD models
1 19.5 19.5
214 14
323 23
4 88 188
535 35
660 60
785 85
8 145 145
9 322 275
10 342 to 392 372 to 422
11 965 956*
1, 1,071*2
12 1,287 1,231*1, 1,346*2
13 30 30
14 525 525
15 1,050 1,050
I21A042
2
13
4
05engL2_240082_4 22-01-2004 13:04 Page 5-9

STARTING AND DRIVING
5-13 Starting (diesel-powered vehicles)
EI02BAH
1. Insert the ignition key and fasten the
seat belt.
2. Apply the parking brake.
3. Depress and hold the brake pedal.
4. Place the gearshift lever (manual
transmission) in the “N” (Neutral) or
the selector lever (automatic trans-
mission) in the “P” (PARK) position.
5. Fully depress the clutch pedal (man-
ual transmission).
6. After turning the ignition key to the
“ON” position, make certain that all
warning lamps are functioning prop-
erly before starting the engine.
7. Turn the ignition key to the “START”
position without depressing the accel-
erator pedal, and release it when the
engine starts.8.
Operate the accelerator pedal as de-
scribed below in accordance with the
atmospheric temperature and/or en-
gine condition and then start the en-
gine.
(1) When the atmospheric temperature is
moderate or the engine is warm, start
the engine without depressing the
accelerator pedal.
(2) When the atmospheric temperature is
low and the engine is cold, start the
engine while following the proce-
dures:
• 2WD with turbocharger, 4WD with
catalytic converter
While depressing the accelerator
pedal, start the engine.
• 2WD without turbocharger, 4WD
without catalytic converter
Start the engine without depress-
ing the accelerator pedal. NOTE
(1) If the engine is cold, the diesel pre-
heat warning lamp is on for a longer
time.
(2) When the engine has not been start-
ed within about 5 seconds
after the diesel preheat warning lamp
went out, return the ignition key to the
“LOCK” position. Then, turn the key to
the “ON” position to preheat the en-
gine again.
(3) When the engine is warm, the diesel
preheat warning lamp does not come
on even if the ignition key is placed in
the “ON” position.
Start the engine by turning the
ignition key right to the “START” posi-
tion.
I27A032
PN
05engL2_240082_4 22-01-2004 13:04 Page 5-13

STARTING AND DRIVING
5-17 Selector positions
EI04B-Cp
P - PARK
This position locks the transmission to
prevent the vehicle from moving. The en-
gine can be started in this position.
R - REVERSE
Move the lever to this position only after
the vehicle has come to a complete stop.
CAUTIONNever shift into the “P” (PARK) or
“R” (REVERSE) position while the
vehicle is in motion. If the lever is
shifted into the “P” or “R” position
while the vehicle is in motion, the
transmission may be damaged.
N - NEUTRAL
At this position the transmission is disen-
gaged. It is the same as the neutral posi-
tion on a manual transmission, and should
be used when the vehicle is stationary for
an extended length of time during driving,
such as in a traffic jam.
L - LOW
This position is for driving up very steep
hills and for engine braking at low speeds
when descending steep gradients.
WARNINGThis position can be used for max-
imum engine braking.
Be very careful not to shift into “L”
suddenly. Sudden engine braking
may cause the tyres to slip.
Select this position according to the
road conditions and vehicle speed.
WARNING(1) Never move the selector lever to
the “N” position while driving. A
serious accident could occur
since you could accidentally
move the lever into the “P” or
“R” position, and engine brak-
ing would not be provided.
(2) The engine should be started in
the “P” (PARK) position, not in
the “N” (NEUTRAL) position.
(3) Always keep your right foot on
the brake pedal when the vehicle
is in “N” (NEUTRAL), or when
shifting into or out of “N” (NEU-
TRAL), to minimize the risk of
loss of control.
D - DRIVE
This position is for normal driving. The
transmission automatically selects a suit-
able gear for your speed and acceleration.
2 - SECOND
This position is for extra power when driv-
ing up moderately steep hills, and for en-
gine braking when descending moder-
ately steep gradients.
05engL2_240082_4 22-01-2004 13:05 Page 5-17

FOR PLEASANT DRIVING
2 - Blower lever
There are 4 blower speeds for control
of the amount of air flow.
The setting for ordinary use should be
the first or second speed.
3 - Temperature control dial
The heater will not operate if the dial
is set all the way to the left.
The air flow temperature will gradually
increase as the dial is turned to the
right.
NOTE
When the engine coolant temperature is
low, temperature of air introduced into the
passenger compartment does not change
even if the temperature control dial is
moved to the high temperature side.A: From front and side demister
B: From side ventilators
C: From under the instrument panel
D: From centre ventilators
(1) *: means a small amount of air flow
(2)
mode: the amount of air flow varies
according to the position of mode selection
dial.
6-20
H16A119
A
BA
A
C
CB D
H03A017
Mode SelectionAir Outlets
B D

A* B* C* D*
C A* B*
A* B* C*
A B*
06engL2_240082_4 22-01-2004 13:07 Page 6-20

FOR PLEASANT DRIVING
4 - Mode selection dial
Main flow directions:
(Face position)
Air flows to the upper part of the pas-
senger area.

(Foot/Face position)
Air flows to the upper part of the pas-
senger compartment, and the leg
area.
(Foot position)
Air flows to the front and rear leg ar-
eas.
(Foot/demister position)
Air flows to the front and rear leg ar-
eas, and windscreen and door win-
dows.
(Demister position)
Air flows to the windscreen and the
door windows.
NOTE
At the foot position and foot/face position,
a small amount of air will be directed to the
windscreen and the door windows.
Leg area heatingEH03B-Bd
Set the mode selection dial and air selec-
tion lever to the positions shown in the il-
lustration.
Adjust the temperature by turning the tem-
perature control dial clockwise or anti-
clockwise.
Select the desired blower speed.
NOTE
When the maximum heating is needed,
set the blower speed at 3rd position. 5 - Air selection lever
(Outside position)
Outside air is introduced into the
passenger compartment.
(Recirculation position)
Air is recirculated inside the pas-
senger compartment.
NOTE
Normally, use the “ ” (outside) position
to keep the windshield and side windows
clear and quickly remove fog or frost from
the windscreen.
If high cooling performance is desired, or if
the outside air is dusty or otherwise conta-
minated, use the “ ” (recirculation) po-
sition. But in this case, set the air selection
lever to the “ ” (outside) position peri-
odically to ventilate so that the window
does not become fogged up.
CAUTIONUse of the “ ” (recirculation) posi-
tion for extended time causes the
windows to fog up.
6-21
H03B030
LHD
06engL2_240082_4 22-01-2004 13:07 Page 6-21

FOR PLEASANT DRIVING
Cooling (vehicles with
air conditioning)
EH04FBA
Set the mode selection dial and air selec-
tion lever to the positions shown in the il-
lustration and push the air conditioning
switch (A).
Adjust the temperature by turning the tem-
perature control dial clockwise or anti-
clockwise. Select the desired blower
speed.
Automatic air conditioning*
EH14A-Ta
By simply pressing the “AUTO” button and
select the desired temperature, the air
conditioning operates to cool or warm
automatically in order to maintain the
selected temperature.
You can also operate it manually if neces-
sary.
The air conditioning can only be operated
while the engine is running.
CAUTIONWhen using the air conditioning, the
idling speed may slightly increase
as the air conditioning compressor
is switched on/off automatically.
Especially for vehicles with an auto-
matic transmission, while the vehi-
cle is stationary, fully depress the
brake pedal to prevent the vehicle
from creeping.
NOTE
If the outside air is dusty or otherwise con-
taminated, or if increased cooling perfor-
mance is desired, set the air selection
lever to the “ ” (recirculation) position
and the temperature control dial all the
way to the left.
Set the “
”(outside) position periodi-
cally to increase ventilation so that the
windows do not become fogged up.
CAUTIONWhen using the air conditioning, the
idling speed may slightly increase
as the air conditioning compressor
is switched on/off automatically.
Especialy for vehicles with an auto-
matic transmission, while the vehi-
cle is stationary, fully depress the
brake pedal to prevent the vehicle
from creeping.
6-25
H04F114
A
LHD
H04F115
A
RHD
06engL2_240082_4 22-01-2004 13:07 Page 6-25