2004 MITSUBISHI ENDEAVOR air condition

Fig. 86: Checking Connector C
-102

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Are immobilizer-ECU connector C-39 and combination meter
connector C-102 in good condition?
YES: Go to Step 4.
NO: Repair or replace the component(s). Confirm that scan tool MB99
1958 communicates normally.
STEP 4. Check the wiring harness between combination meter connector
C-102 (terminal 19) and immobilizer-ECU connector C-39 (terminal 5).
Fig. 87: Checking Connector C
-39
Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 88: Checking Wiring Harness Between Combination Meter Connector C
-102

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the wiring harness between combination meter connector C-102
(terminal 19) and immobilizer-ECU connector C-39 (terminal 5) in good
condition?
YES: Go to Step 5.
NO: Repair the wiring harness. Confirm the immobilizer indicator light
illuminate normally.
STEP 5. Measure the voltage at combination meter connector C-102 in
order to check the battery circuit of power supply system to the
combination meter.
1. Turn the ignition switch to the "LOCK" (OFF) position.
2. Disconnect combination meter connector C-102, and measure at the
wirin
g harness side.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Fig. 91: Identifying Connector C
-102

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is combination meter connector C-102 in good condition?
YES: Go to Step 7.
NO: Repair or replace the component(s). Confirm the immobilizer
indicator light illuminate normally.
STEP 7. Check the wiring harness between combination meter connector
C-102 (terminal 1) and the battery.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Q: Is the wiring harness between combination meter connector C-102
(terminal 1) and the battery in good condition?
YES: Go to Step 8.
NO: Repair the wiring harness. Check to see that all meters operate.
STEP 8. Retest the system.
Q: Is the malfunction eliminated?
YES: The procedure is complete. (If no malfunctions are found in all
steps, an intermittent malfunction is suspected. Refer to HOW TO USE
TROUBLESHOOTING/ INSPECTION SERVICE POINT
).
NO: Replace the combination meter.
DATA LIST REFERENCE TABLE Fig. 94: Data List Reference Table

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
CHECK AT IMMOBILIZER-ECU < UP TO DECEMBER 2003 > TERMINAL VOLTAGE CHEC
K

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Ignition Switch - Endeavor

Q: Are joint connector (2) C-104 and junction block connector C-211 in
good condition?
YES: Go to Step 3.
NO: Repair or replace the damaged connector(s).
P.00E-2. Check if the all heated door mirrors works normally.
STEP 3. Check the wiring harness between joint connector (2) C-104
(terminal 25) and junction block connector C-211 (terminal 3).
Fig. 4: Identifying Connector C
- 104

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door Mirror - Endeavor

and junction block connector C-211 (terminal 3) in good condition?
YES: Go to Step 4.
NO: Repair the wiring harness as necessary. Check if the all heated door
mirrors works normally.
STEP 4. Check remote controlled mirror (LH) connector E-14.
Fig. 6: Identifying Connector E
- 14

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is remote controlled mirror (LH) connector E-14 in good condition?

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door Mirror - Endeavor

Fig. 9: Identifying Connector C
- 29

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is the wiring harness between joint connector (2) C-104 (terminal 23)
and remote controlled mirror (LH) connector E-14 (terminal 1) in good
condition?
YES: Go to Step 6.
NO: Repair the wiring harness as necessary. Check if the all heated door
mirrors works normally.
STEP 6. Check remote controlled mirror (RH) connector E-01.

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door Mirror - Endeavor

Fig. 10: Identifying Connector E
- 01

Courtesy of MITSUBISHI MOTOR SALES OF AMERICA.
Q: Is remote controlled mirror (RH) connector E-01 in good condition?
YES: Go to Step 7.
NO: Repair or replace the damaged connector. Check if the all heated
door mirrors works normally.
STEP 7. Check the wiring harness between joint connector (2) C-104
(terminal 24) and remote controlled mirror (RH) E-01 (terminal 1).

2004 Mitsubishi Endeavor LS
2004 BODY & ACCESSORIES Door Mirror - Endeavor