2004 MERCEDES-BENZ CL-Class light

2 IntroductionSymbolsYou will find the following symbols in these
operating instructions:
* The asterisk identifies optional
equipment. Since not all models
have the same standard equip-
ment, your COMAND system equip-
ment may deviate from some
descriptions and illustrations.

This symbol points to instructions for
you to follow.

A number of these symbols appearing
in succession indicates a multiple-step
procedure.
The continuation symbol
marks an interrupted proce-
dure which will be continued
on the next page.
(
page 3) This symbol tells you where
to look for further infor-
mation on this subject.
-> This symbol is used in the
glossary. It indicates that
the term immediately follo-
wing the symbol is also exp-
lained in the glossary.
Display
Messages, menu items or
soft key names appearing in
the COMAND color display
are printed in the type
shown here.
Warning
G
Warning notices draw your attention to ha-
zards that may endanger your health or life,
or the health or life of others.!Highlights hazards that may result in
damage to your COMAND.iHelpful hints or further information you
may find useful.


Symbols

36 AudioRadio operationYou can use the following functions:
Saving stations manually (FM, AM)

Saving stations automatically FM, AM
(page 37)

Selecting a station from the FM/AM
Preset menu (
page 38)

Selecting a station from the FM/AM
Auto presets (
page 38)Saving stations manually (FM, AM)
In the Radio main menu

Activate the desired waveband
(page 32).

Press one of the number keys, e.g. 2,
longer than 2 seconds.
You will hear a confirmation beep if the
beep tones option was activated in the
system settings (
page 199).
The radio saves the current station at
the memory preset selected. The me-
mory preset selected will appear in the
status line, e.g. “FM2”.On the memory list

Activate the desired waveband
(page 32).

Press the
Presets
soft key.
The memory Preset menu will appear.

Use H, h or g, G to highlight
the desired memory preset.

Press E
longer than 2 seconds.
The current station will be saved at the
memory preset selected.
You will hear a confirmation beep if the
beep tones option was activated in the
system settings (
page 199).
Memory functions
iThere are 10 presets available (1 -
9, 0).
An existing entry is overwritten in the
memory list when a new input is given.

38 AudioRadio operationSelecting a station from the preset
menu (FM, AM)
Activate the FM or AM memory
(page 36).
You can use one of the following two ways
to select a station from the FM/AM
presets

Press the corresponding number key,
e.g. 3, to select the desired station.
or

Use H, h or g, G to highlight a
memory preset in the FM/AM preset
list.

Press E.
In both cases, you will see the Radio
main menu
automatically after 8 seconds

if you press the
Back
soft key.
The Radio main menu indicating the
memory preset number appears.Selecting a station from the FM/AM
autostore presets

Activate the FM or AM autostore pre-
sets (
page 37).

Use H, h or g, G to highlight a
memory position.

Press E.
You will see the Radio main menu
automatically after 8 seconds

if you press the
Back
soft key.

40 AudioTape operation
Do not expose the tapes to direct
sunlight or high temperatures.

Do not leave tapes near magnetic fields
or magnets.

Ensure that the tape is adequately
tightened before you insert it into the
tape slot.

Do not touch the tape with your fingers.

Do not insert a tape if its label is not
stuck on properly.

Press A.
The Audio menu will appear
(page 30).

Press the
Tape
soft key.
The Tape main menu will appear.
Tape main menu
E.g.:
Tape
= Tape operation switched on

Side 1
= Side display
Tape inserted:
Tape operation begins with the track
last played.
No tape inserted:
The message
No tape
will appear.

Insert a cassette (
page 41).
In the case of a device or tape error:
The message
Tape error
will appear.
Notes on tape careWarning
G
In order to avoid distraction which could
lead to an accident, the driver should insert
tapes with the vehicle at a standstill and
operate the audio system only if permitted
by road, weather and traffic conditions.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your car covers a
distance of 50 feet (approximately 14 m)
every second.
Switching tape operation on
iThe
Sound
soft key will appear if the
COMAND is provided with sound
functions* (page 27).
iThe telephone and navigation functions
can be used while a tape is playing.

Tape operation

46 AudioCD operation
Only touch the CD on the sides.

Avoid touching the CD surface with
your fingers.

Clean the CD with a dry, lint-free cloth.
Wipe them from the inside to the outer
edge. Never wipe the CD in a circular
motion.

Do not use rubbing alcohol or solvents
to clean the CDs.

Do not expose the CDs to heat or direct
sunlight.

Do not write or put stickers on CD.Tips on caring for your CDs

47 Audio
CD operation
Playback locations for audio CDs are:
the CD drive in the COMAND

the CD changer*.
Differences regarding the CD mode
depending on the audio source are
highlighted.

In the Audio menu (
page 30), press
the
CD
or the
CD
soft key.
CD changer* main menu
CD drive
CD changer*
Switching to CD operation
iThe
CD-Mag
soft key is only assigned
when the CD changer* is active.
The
Sound
soft key appears if the
COMAND is provided with sound
functions* (page 27).
iThe CD drive in the COMAND can
playback audio CDs, MP3-CDs
(page 56). The slot of the drive is
behind the display.
iThe CD changer* can accomodate up
to 6 audio CDs. It is located on the left-
hand side in the trunk.
Loading CDsWarning
G
In order to avoid distraction which could
lead to an accident, the driver should insert
CDs with the vehicle at a standstill and
operate the audio system only if permitted
by road, weather and traffic conditions.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your car covers a
distance of 50 feet (approximately 14 m)
every second. iThe COMAND may be unable to
playback audio CDs provided with copy
protection.

56 AudioMP3-CD operation

Treat MP3-CDs with care to prevent
malfunctions during playback.

Do not scratch, touch or soil your MP3-
CDs.

Do not attach labels to or write on your
MP3-CDs.

From time to time, clean your MP3-CDs
with a commercially available cleaning
cloth. Never wipe circularly, but in a
straight line from inside to outside.

After use, put your MP3-CDs into the
CD box.

Protect your MP3-CDs from high
temperatures and direct sunlight.
General InformationWarning
G
In order to avoid distraction which could
lead to an accident, the driver should insert
CDs with the vehicle at a standstill and
operate the audio system only if permitted
by road, weather and traffic conditions.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your car covers a
distance of 50 feet (approximately 14 m)
every second.
Warning
G
The CD drive and CD changer* are Class 1
laser products. There is a danger of invisible
laser radiation when you open or damage
the cover.
Do not remove the cover. The CD drive and
the CD changer* do not contain any parts
which can be serviced by the user. For safe-
ty reasons, have any necessary service work
performed by qualified personnel.iWhen you create a MP3-CD you can
define structures and input information
in addition to the title information. iThe COMAND plays the tracks on the
MP3-CD in alphabetical order. To
preserve the order on the original CD,
number the tracks in ascending order
when you record them.
Tips on caring for your MP3-CDs

MP3-CD operation

64 AudioDVD operation
From time to time, clean your DVDs
with a commercially available cleaning
cloth. Never wipe circularly, but in a
straight line from inside to outside.

After use, put your DVDs into the DVD
box.

Protect your DVDs from high
temperatures and direct sunlight.

Load a video DVD into the COMAND
(page 65).
or

If a DVD is already loaded, open the Au-
dio menu (
page 30) and press the
DVD
soft key.
If the video DVD meets the playback re-
quirements, playback will begin. If avai-
lable, the DVD menu (
page 70) saved
on the DVD will appear.
DVD playback requirementsiVendors may offer DVDs which do not
comply with the standards.
Sound, picture and other playback
problems may occur when you play
such DVDs.
The COMAND can playback video
DVDs meeting the following
requirements:
Regional code is set (factory
setting)

NTSC or PAL TV standard
The appropriate information is usually
given either on the DVD or the DVD
box. The factory setting of the
COMAND is regional code 1. The
setting can be changed in a Mercedes-
Benz Service Center. This will allow you
to playback video DVDs with other
regional codes, as long as they comply
with the NTSC or PAL TV standard.
iThe COMAND system is capable of
playing DVDs. However, in order to
avoid driver distraction, the video
function is disabled and no images will
be shown on the COMAND screen.Switching to DVD operation