2004 JEEP GRAND CHEROKEE towing

To Resume Speed
To resume a previously set speed, press and release the
RES´ACCEL button. Resume can be used at any speed
above 30 mph (48 km/h).
To Vary the Speed Setting
When the Speed Control is ON, speed can be increased
by pressing and holding the RES´ACCEL button. When
the button is released, a new set speed will be estab-
lished.
Tapping the RES´ACCEL button once will result in a 2
mph (3 km/h) speed increase. Each time the button is
tapped, speed increases, so tapping the button three
times will increase speed by 6 mph (10 km/h), etc.
To decrease speed while Speed Control is ON and SET,
press and hold the COAST button. Release the button
when the desired speed is reached, and the new speed
will be set.
To Accelerate for Passing
Depress the accelerator as you would normally. When the
pedal is released, the vehicle will return to the set speed.
NOTE:When driving uphill, at elevations above 2,000
feet (610 meters), or when the vehicle is heavily loaded
(especially when towing) the vehicle may slow below the
SET speed. If the vehicle speed drops below 30 mph (48
km/h), the Speed Control will automatically disengage.
If this happens, you can push down on the accelerator
pedal to maintain the desired speed.
Vehicles may exhibit several 4-3 downshifts under the
above conditions. To reduce the frequency of the down-
shifts and to improve vehicle performance, it is advisable
to lock out overdrive. Press the O/D OFF button on the
side of the shift lever.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87
3

7. Oil Pressure Gage
Indicates the engine oil pressure. This gage does
not measure oil level. Pressure varies with engine
speed, temperature, and oil viscosity. Normal oil pressure
will be midway between the lowest and highest limit
marks.
8. Sentry Key Indicator Light Ð If Equipped
Refer to ªSentry Key Immobilizer Systemº in
Section 2 of this manual for more information.
9. Malfunction Indicator Light
This light is part of an onboard diagnostic system
called OBD II which monitors engine and auto-
matic transmission control systems. This light
will illuminate when the ignition is in the ON position
before engine start. If the bulb does not come on when
turning the ignition key from OFF to ON, have the
condition checked promptly.Certain conditions such has a loose or missing gas cap,
poor fuel quality, etc. may illuminate the light after
engine start. The vehicle should be serviced if the light
stays on through several typical driving cycles. In most
situations, the vehicle will drive normally and will not
require towing.
When the engine is running, the ªMalfunction Indicator
Lightº may flash to alert of serious conditions that could
lead to immediate loss of power or severe catalytic
converter damage. The vehicle should be serviced as
soon as possible if this occurs.
10. Cruise Indicator Light
This indicator lights when the electronic speed
control system is turned ON.
11. Check Gages Warning Light
This light illuminates when the voltmeter, oil
pressure, or temperature gages indicate a reading
130 UNDERSTANDING YOUR INSTRUMENT PANEL

either too high or too low. Examine the gages carefully,
and follow the instructions above for each indicated
problem.
NOTE:When the ignition switch is turned to OFF, the
fuel gage, voltmeter, oil pressure, and temperature gages
will not show any readings. When the engine is not
running, turn the ignition switch to ON to obtain accu-
rate readings.
12. Part Time Indicator Light
This light alerts the driver that the vehicle is in
the PART TIME four±wheel drive mode, and
the front and rear driveshafts are mechanically
locked together forcing the front and rear wheels to rotate
at the same speed.
13. Transmission Over Temperature Warning Light
This light indicates that there is excessive transmis-
sion fluid temperature that might occur with severe
usage such as trailer towing or snow plowing. If this lightcomes on, stop the vehicle and run the engine at idle or
faster, with the transmission in N (Neutral) until the light
goes off.
14. Temperature Gage
Indicates engine coolant temperature. Any read-
ing within the normal range indicates that the
cooling system is operating satisfactorily.
The gage pointer will likely indicate a higher temperature
(above center scale) when driving in hot weather, up
mountain grades, or when towing a trailer. It should not
be allowed to exceed the upper limits of the normal
operating range.
If the pointer rises to the 260É (Hot) mark, pull over and
stop the vehicle. Do not turn the engine off. Idle the
vehicle with the air conditioning turned off, until the
pointer drops back into the normal range.
UNDERSTANDING YOUR INSTRUMENT PANEL 131
4

NTire Spinning........................214
NTread Wear Indicators..................215
NReplacement Tires.....................215
NAlignment And Balance.................217
mTire Pressure Monitor System Ð If Equipped . . . 217
NTire Pressure Monitor System Tire/Wheel
Rotation And Sensor Replacement Ð If
Equipped...........................218
NGeneral Information...................219
mTire Chains...........................220
mTire Rotation Recommendations............220
mFuel Requirements......................221
NReformulated Gasoline.................222
NGasoline/Oxygenate Blends..............222NMMT In Gasoline.....................223
NSulfur In Gasoline.....................223
NMaterials Added To Fuel................224
mFuel Tank Filler Cap (Gas Cap).............224
mTrailer Towing.........................226
NTrailer And Tongue Weight..............228
NCooling System TipsÐTrailer Towing.......229
NMinimum Vehicle Requirements For Trailer
Towing............................230
mRecreational Towing (Behind Motorhome, Etc.) . . 231
NShifting Into Neutral (N)................232
NShifting Out Of Neutral (N)..............233
mSnow Plow...........................234
STARTING AND OPERATING 175
5

²Vehicle speed is above approximately 30 mph (48
km/h).
²Transmission has reached normal operating tempera-
ture.
When frequent transmission shifting occurs while using
overdrive, such as when operating the vehicle under
heavy load conditions (for example, in hilly terrain,
strong head winds, or trailer towing), turning off over-
drive will improve performance and extend transmission
life by reducing excessive shifting and heat buildup.
4th and 5th gears (Overdrive) can be locked out by
pressing the O/D OFF switch located on side of the
gearshift lever. The O/D OFF indicator light will illumi-
nate to show that the switch has been activated. When
the light is on, 4th and 5th gears (Overdrive) are locked
out. Pressing the switch a second time restores the
Overdrive function. The lockout feature is useful when
towing a trailer or carrying a heavy load.The O/D OFF feature must be selected, if desired, each
time the engine is started.
NOTE:If the vehicle is started in cold outside tempera-
tures, shifts into Overdrive may be delayed (4.7L engines
only). Normal Overdrive and shifting operation will
resume when the temperature of the transmission
STARTING AND OPERATING 183
5

N (Neutral)
Neutral Ð Disengages both the front and rear driveshafts
from the powertrain. To be used for flat towing behind
another vehicle. Refer to ªRecreational Towingº in Sec-
tion 5 of this manual.
4LO
Part Time Four Wheel Drive Low Range Ð Low speed 4
wheel drive. Locks the transfer case inter-axle differen-
tial. Forces the front and rear wheels to rotate at the same
speed. Additional traction and maximum pulling power
for loose, slippery road surfaces only. Do not exceed 25
mph (40 km/h).
Shifting Procedure
2WD to 4 PART TIME or 4 PART TIME to 2WD
Shifting between 2WD and 4 PART TIME can be made
with the vehicle stopped or in motion. If the vehicle is in
motion, shifts can be made up to 55 mph (88 km/h). With
the vehicle in motion, two momentary releases of the
accelerator pedal may be required after shifting. This will
STARTING AND OPERATING 189
5

WARNING!
You or others could be injured if you leave the
vehicle unattended with the transfer case in the N
(Neutral) position without first fully engaging the
parking brake. The transfer case N (Neutral) position
disengages both the front and rear driveshafts from
the powertrain and will allow the vehicle to move
regardless of the transmission position. The parking
brake should always be applied when the driver is
not in the vehicle.
Shift Positions
For additional information on the appropriate use of each
transfer case mode position, see the information below:
4 ALL TIME
Normal All Wheel Drive High Range Ð All roads sur-
faces such as ice, snow, gravel, sand, and dry hard
pavement.
N (Neutral)
Neutral Ð Disengages both the front and rear driveshafts
from the powertrain. To be used for flat towing behind
another vehicle. Refer to ªRecreational Towingº in Sec-
tion 5 of this manual.
4LO
Four Wheel Drive Low Range Ð Low speed 4 wheel
drive. Locks the front and rear driveshafts together.
Forces the front and rear wheels to rotate at the same
192 STARTING AND OPERATING

Loading
The vehicle maximum load on the tire must not exceed
the load carrying capacity of the tire on your vehicle. You
will not exceed the tire's load carrying capacity if you
adhere to the loading conditions, tire size and cold tire
inflation pressures specified on the Tire and Loading
Information placard and the Vehicle Loading section of
this manual.
NOTE:Under a maximum loaded vehicle condition,
gross axle weight ratings (GAWR's) for the front and rear
axles must not be exceeded. For further information on
GAWR's, vehicle loading and trailer towing, see the
Vehicle Loading section of this manual.To determine the maximum loading conditions of your
vehicle, locate the statement ªThe combined weight of
occupants and cargo should never exceed XXX kg or XXX
lbs.º on the Tire and Loading Information placard. The
combined weight of occupants, cargo/luggage and
trailer tongue weight (if applicable) should never exceed
the weight referenced here.
Steps for Determining Correct Load Limit
1. Locate the statement ªThe combined weight of occu-
pants and cargo should never exceed XXX poundsº on
your vehicle's placard.
2. Determine the combined weight of the driver and
passengers that will be riding in your vehicle.
208 STARTING AND OPERATING