2004 ISUZU TF SERIES stop start

7A3-18 ON-VEHICLE SERVICE (AW30 –40LE)

“ L" Range Test
1. While running above 80 km/h (50 mph) in the “D"
range, release your foot from the accelerator pedal
and shift into the “L" range.
Then check to see that the 2 
1 downshift occurs at
the specified point shown on the automatic shift
diagram.



RUW37ASH000601
2. While running in the “L" range, check to see that
there is no upshift to 2nd gear.
3. While running in the “L" range, release the
accelerator pedal and check the engine braking
effect.
4. Check for abnormal noise during acceleration and deceleration.







RUW37ASH000701

“ R" Range Test
Shift into the “R" range and, while starting at full throttle,
check for slipping.




RUW37ASH000801
“ P" Range Test
Stop the vehicle on a grade (more than 9%) and afte
r
shifting into the “P" range, release the parking brake.
Then check to see that the parking lock pawl holds the
vehicle in place.

DIAGNOSIS (JR405E) 7A2-3
PAGE
No. B12: NOISE OR VIBRATION IS GENERATED AT STARTING..................................7A2-107
No. C1: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFTED UP TO 1st TO 2
nd........7A2-108
No. C2: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFTED UP TO 2nd TO 3
rd.......7A2-108
No. C3: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFTED UP TO 3rd TO 4
th........7A2-108
No. C4: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFT DOWN ................................7A2-108
OR KICK-DOWN TO 4th TO 3
rd.................................................................................7A2-108
No. C5: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFT DOWN OR KICK-DOWN
TO 4th TO 2
nd..............................................................................................................................7A2-108
No. C6: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFT DOWN OR KICK-DOWN
TO 3rd TO 2
nd.............................................................................................................................7A2-108
No. C7: ENGINE RACE UP (SLIP) WHEN GEAR IS SHIFT DOWN TO 4th OR 3
rd
TO 1
st............................................................................................................................................7A2-108
No. C8: ENGINE RACE UP (SLIP) OTHERS.........................................................................7A2-108
No. C9: BARKING FEEL WHEN GEAR IS SHIFTED UP TO 1st TO 2
nd.........................7A2-111
No. C10: BARKING FEEL WHEN GEAR IS SHIFTED UP TO 2nd TO 3
rd......................7A2-111
No. C11: BARKING FEEL WHEN GEAR IS SHIFTED UP TO 3rd TO 4
th.......................7A2-111
No. C12: LARGE SHOCK WHEN GEAR IS SHIFTED TO 1st TO 2
ND OR 2nd TO 1st..7A2-114
No. C13: LARGE SHOCK WHEN GEAR IS SHIFTED TO 2nd TO 3
rd OR 3rd TO 2nd.7A2-114
No. C14: LARGE SHOCK WHEN GEAR IS SHIFTED TO 3rd TO 4th TO 3
rd................7A2-114
No. C15: LARGE SHOCK WHEN KICK-DOWN....................................................................7A2-114
No. C16: LARGE SHOCK WHEN NO ACCELERATION.....................................................7A2-114
No. C17: LARGE SHOCK WHEN GEAR IS SHIFTED DOWN TO 2nd TO
1st IN L RANGE..........................................................................................................................7A2-114
No. C18: LARGE SHOCK (OTHER)........................................................................................7A2-114
No. C19: LARGE SHOCK WHEN VEHICLE SPEED IS DOWNED BY NO
ACCELERATOR PANEL OR VEHICLE IS STOPPED........................................................7A2-114
No. C20: LARGE LOCK-UP SHOCK.......................................................................................7A2-114
No. C21: SHIFT DOWN OR ENGINE OVER-RUN WHEN THE ACCELERATION
PANE IS STEPPED ON IN 4th GEAR....................................................................................7A2-114
NO. D1: FAULTY GEAR SHIFTING (DIFFERENT FROM SHIFT PATTERN)............... 7A2-115
NO. D2: GEAR IS SHIFTED FREQUENTLY ................................................................. 7A2-120

7A2-4 DIAGNOSIS (JR405E)
PAGE
NO. D3: GEAR SHIFT POINT IS LOW OR HIGH AT ALL POINT................................. 7A2-120
NO. D4: GEAR SHIFT POINT IS LOW OR HIGH AT LIMITED POINT ......................... 7A2-120
NO. D5: NO KICK-DOWN .............................................................................................. 7A2-120
NO. E1: NO GEAR SHIFT .............................................................................................. 7A2-121
NO. E2: ONLY 4TH GEAR (O/D) IS NOT SELECTABLE ............................................. 7A2-124
NO. E3: GEAR IS SHIFTED 2ND TO 3RD IN 2 RANGE ............................................... 7A2-126
NO. E4: GEAR IS SHIFTED 1ST TO 2ND IN L RANGE................................................ 7A2-126
NO. E5: GEAR IS SHIFTED 3RD TO 4TH IN 3 RANGE................................................ 7A2-126
NO. F1: LOW MAXIMUM SPEED OR POOR ACCELERATION ................................... 7A2-127
NO. F2: ENGINE RACES UP DURING ACCELERATION (SLIP) ................................. 7A2-130
NO. F3: NOISE OR VIBRATION DURING THE RUNNING IN R, D, 3, 2 OR L
RANGE .......................................................................................................................... 7A2-130
NO. F4: ENGINE BRAKE DOES NOT APPLY IN L RANGE......................................... 7A2-130
NO. F5: ENGINE STALLS BEFORE VEHICLE STOPS FROM RUNNING ................... 7A2-131
NO. G1: VEHICLE MOVES IN P RANGE OR PARKING GEAR IS NOT
DISENGAGED OTHER THAN P RANGE ..................................................................... 7A2-131
NO. G2: CREEP FORCE IS LARGE.............................................................................. 7A2-131
NO. G3: CREEP FORCE IS SMALL .............................................................................. 7A2-132
NO. G4: LARGE NOISE DURING IDLING WITH THE VEHICLE IN STOP STATE ...... 7A2-133
NO. H1: JUDDER OCCURS AT THE LOCK-UP ........................................................... 7A2-133
NO. H2: LARGE LOCK-UP SHOCK .............................................................................. 7A2-133
NO. H3: LOCK-UP POINT IS HIGH OR LOW ............................................................... 7A2-133
NO. I1: NO LOCK-UP .................................................................................................... 7A2-134
NO. J1: OIL LEAKS FROM BREATHER ....................................................................... 7A2-136
NO. J2: OIL LEAKS BETWEEN ENGINE AND CONVERTER HOUSING .................... 7A2-136
NO. J3: OIL LEAKS BETWEEN MAIN CASE AND CONVERTER HOUSING.............. 7A2-136
NO. J4: OIL LEAKS BETWEEN MAIN CASE AND REAR HOUSING .......................... 7A2-136
NO. J5: OIL LEAKS FROM OIL PAN ............................................................................ 7A2-136
NO. J6: OIL LEAKS FROM MANUAL SHAFT OIL SEAL ............................................. 7A2-136
NO. J7: OIL LEAKS FROM OIL COOLER PIPE JOINT................................................ 7A2-136
NO. Z1: TRANSMISSION OVERHEAT .......................................................................... 7A2-136
NO. Z2: MODE LAMP (POWER DRIVE OR 3RD START) DOES NOT LIGHT UP
WHEN THE POWER MODE OR 3RD START MODE IS TURNED ON........................ 7A2-137

DIAGNOSIS (JR405E) 7A2-31
CONNECTOR LIST
TCM
No. Connector face No. Connector face
B-23
Green
Meter-A B-73

SilverWeld splice 3 (Earth)
B-24
Green
Meter-B C-2
SilverEngine room-RH ground
B-50
White
Power/3rd start switch C-44
WhiteStop lamp switch
B-54
White
J/B I2 C-56
(4JH1-TC)
ECM-A
B-56
White
J/B I4 C-57
(4JH1-TC)
ECM-B
B-58
Black
Check connector C-94
(6VE1)
(4JH1-TC)
Gray TCM
B-62
White
Ignition switch (IGSUB : G1) C-95
(6VE1)
(4JH1-TC)
WhiteTCM
B-63
White
Ignition switch (IGSUB : G2) C-107
WhiteJ/B E2
B-64
Silver
Weld splice 1 (Illumination) C-109
SilverBody-LH ; ground
B-68
(4JH1TC,
6VE1)
White Immobilizer C/U E-10

SilverEngine; ground

DIAGNOSIS (JR405E) 7A2-79

Step Action Yes No
1 Turn the key switch on and check the DTC. Is only the DTC for
low & reverse brake fail-safe valve failure outputted?
Go to Step 2
Go to Other DTC
Section
2 Clear the DTC from the memory. Turn the key switch off once,
and then start the engine. Does the CHECK TRANS blink
when the D range is selected and about 10 seconds elapsed?
Go to Other DTC
Section Go to Step 3
3 Run the vehicle, shift the gear from 1st to 4th, stop the vehicle,
and again shift the gear from 1st to 4th. Does the CHECK
TRANS blink at this time?
Go to Step 4
The low & reverse
brake fail-safe valve
may be faulty
temporarily.
Go to step 5
4 Turn the key switch on and check the DTC. Is only the DTC for
the low & reverse brake fail-safe valve failure outputted?
Repair or replace the
control valve.
Go to Step 5
Go to Other DTC
Section
5 Clear the DTC from the memory and perform the work after
repair. Is the same DTC code outputted again in the
subsequent DTC check?
Replace the TCM Go to Step 6
6 Are the other DTCs outputted?
Go to Other DTC
Section Action is completed

DIAGNOSIS (JR405E) 7A2-81

Step Action Yes No
1 Turn the key switch on and check the DTC. Is only the DTC for
2-4 brake fail-safe valve failure outputted?
Go to Step 2
Go to Other DTC
Section
2 Clear the DTC from the memory. Turn the key switch off once,
and then start the engine. Does the CHECK TRANS blink when
the D range is selected and about 10 seconds elapsed?
Go to Other DTC
Section Go to Step 3
3 Run the vehicle, shift the gear from 1st to 4th, stop the vehicle,
and again shift the gear from 1st to 4th. Does the CHECK
TRANS blink at this time?
Go to Step 4
The 2-4 brake fail-safe
valve may be faulty
temporarily.
Go to step 5
4 Turn the key switch on and check the DTC. Is only the DTC for
the 2-4 brake fail-safe valve failure outputted?
Repair or replace the
control valve.
Go to Step 5
Go to Other DTC
Section
5 Clear the DTC from the memory and perform the work after
repair. Is the same DTC code outputted again in the
subsequent DTC check?
Replace the TCM Go to Step 6
6 Are the other DTCs outputted?
Go to Other DTC
Section Action is completed

DIAGNOSIS (JR405E) 7A2-89
Symptom Condition Description
Faulty during the
running Low maximum speed or poor acceleration Starting acceleration is poor. F1
Acceleration is slow though the accelerator
pedal is stepped on during the running.
Engine races up during acceleration (slip)
The engine speeds up but vehicle speed
does not increase when the accelerator
pedal is stepped on at the starting.
F2

Only the engine speeds up but vehicle
speed does not increase when the
accelerator pedal is stepped on for
acceleration during the running.

Noise or vibration during the running in R, D,
3, 2, or L range
Noise or vibration is generated in the vicinity
of AT during the running. F3
Engine brake does not in apply L range
The engine brake does not apply, allowing
the vehicle to run freely when the
accelerator pedal is released at low speed in
L range.
F4
Engine stalls before vehicle stops from
running
The engine stalls simultaneously with the
vehicle stop when the brake pedal is
stepped on to stop the vehicle during the
running.
F5
Faulty in the
stopping
Vehicle moves in P range, or parking gear is
not disengaged other than P range
Vehicle moves though it stops at a slope
and P range is selected. G1

The engine stalls and vehicle does not move
though other than P range is selected and
the accelerator pedal is stepped on.

Creep force is large
Vehicle accelerates in D, 3, 2, L, and R
ranges though the accelerator pedal is not
stepped on.
G2
Creep force is small Vehicle does not move though a run range
is selected on a flat road during the idling. G3
Large noise during idling with the vehicle in
stop state
The transmission is noisy during the idling
speed in all ranges. G4
Faulty lock-up Judder occurs at the lock-up The vehicle body judders at lock-up. H1
Large lock-up shock Large shock is felt at lock-up. H2
Lock-up point is high or low Lock-up point is excessive high or low. H3
No lock-up No lock-up Lockup is not performed in spite of the lock-
up area. I1

DIAGNOSIS (JR405E) 7A2-97
No. B2: Poor Acceleration at Starting

Description:

Starting acceleration is poor.

Diagnosis Hints:

In addition to the low engine output, faulty gear shifting of AT or fixing at the 3rd position may be possible.
Therefore, in case of such a trouble that "maximum speed is low, and acceleration is poor", it should be cleared
up whether the trouble is originated from the engine system of AT system by a running test, inspection of stall
revolution, etc.

Possible Cause:

Clogged air cleaner, out of injection timing, dropped compression pressure, etc.

Fixing at 3rd position (fail-safe activated).
Since the gear is fixed at the 3rd position because of the fail-safe function, a trouble that "Maximum
speed is low, and acceleration is poor" is resulted. In this case, the DTC is memorized.
When TCM stops operation because of faulty TCM ground, the gear is fixed at the 3rd position because
of a mechanical reason. In this case, no DTC is memorized.

Disordered inhibitor switch.

Incorrect properties of throttle opening signal (serial communication) of throttle position sensor.
Throttle opening signal (serial communication) of the throttle position sensor does not change in
proportion to the throttle opening. In this case, fixing at the high or low gear results in such a trouble
that "Maximum Speed is Low and Acceleration is Poor".

Slip of clutch (low clutch, high clutch).

If slip of clutch is caused, a DTC (gear ratio error) is stored.

Dropped line pressure.

Trouble in the torque converter system (faulty operation).

Step Action Yes No
1 Test Drive.
Is the gear smoothly shifted in the order of 1st to 2nd, 2nd to 3rd,
3rd to 4th gear and lock up?

Clogged air cleaner,
out of injection
timing, dropped
compression
pressure, etc.

Go to Step 2
2 Gear ratio trouble diagnosis.
Travel in the following sequence for about 7 seconds or more in
each range: Start in the L range (1st) to 2 range (2nd) to 3 range
(3rd) to D range (4th) (to detect the gear ratio trouble exactly, this
process should be carried out)
Go to Step 3 Go to Step 3
3 Are any DTCs stored?
Go to DTC Chart Go to Step 4