2004 ISUZU TF SERIES diesel

7B1-70 MANUAL TRANSMISSION

4. Install the transmission assembly (18) to the engine.
Tighten the transmission nuts and bolts as shown in
the figure.


Diesel engine
RTW37BLF000901

MANUAL TRANSMISSION 7B1-73

6. Install starter(16).(Diesel engine)
NOTE: Tighten the lower bolt temporarily.
After installing the fuel pipe assembly, tighten the bolt to
the specified torque.
Torque: 76 N




m (7.7 kg




m/56 lb




ft)
7. Install the rear support rubber on the transmission
and tighten the bolts to the specified torque.
Torque: 50 N




m (5.1 kg




m/37 lb




ft)
8. Install the middle part of transmission crossmember
(15) and bolts.
Tighten the nuts to the specified torque.
Torque: 67 N




m (6.8 kg




m/49 lb




ft)
9. Install engine rear mount nuts (14).
Torque: 52 N




m (5.3 kg




m/38 lb




ft)
Remove the transmission jack from transmission
side.
10. Apply grease to top hole portion of the shift fork.
Install slave cylinder (13) and tighten the bolts to the
specified torque.
Torque: 76 N




m (7.7 kg




m/56 lb




ft)
11. Install the fuel pipe brackets on the transmission.
Install the fuel pipe assembly to the fuel pipe
brackets
Torque: Bolt & Nut 76 N




m (7.7 kg




m/56 lb




ft)
Nut 37 N




m (3.8 kg




m/28 lb




ft)
Diesel engine
220R300012

Legend
(1) Bolt
(2) Nut
(3) Fuel Pipe Assembly


6VE1, C24NE
Scan-2
12. Connect transmission harness connectors and clips.
Connector: transfer neutral switch, 2W - 4W switch,
backup switch, transmission neutral switch.
810R300069

Legend
(1) Neutral Switch Connector: Transmission
(2) Backup Switch Connector
(3) Speed Sensor Connector
(4) Actuator Connector
(5) 2W - 4W Switch connector
(6) Neutral Switch Connector: Transfer
13. Apply grease (BESCO L2 or equivalent) on the
splined portion of the output shaft.
14. Connect the transfer to the transmission.

MANUAL TRANSMISSION 7B1-77

Disassembly
1. Clean the exterior of the unit with solvent.
2. Remove the drain plug from the transmission case
and drain the lubricant.
3. Remove the clutch release bearing with spring (5)
from the transmission case.
4. Remove the shift fork, and boot. (Diesel engine,
C24NE)
5. Remove the shift fork snap pin. (6VE1)
6. Remove the shift fork pin and shift fork from the
fulcrum bridge. (6VE1)



RTW47BSH000601

Legend
(1) Shift fork pin
(2) Shift fork
(3) Release bearing
7. Remove the fulcrum bridge from the transmission
case. (6VE1)
RTW37ASH0002

Legend
(1) Fulcrum bridge
8. Remove the front cover (8) and gasket from the
transmission case.
9. Remove snap ring (7) fixing counter front bearing.
10. Use a pair of snap ring pliers to remove the snap
ring (9) fixing top gear bearing.

226RS001
11. Remove gear control box assembly (1).
12. Remove the rear case assembly (2) from the
transmission case (4) and intermediate plate (3).
13. Remove intermediate plate with gear assembly (3)
from transmission case (4).

MANUAL TRANSMISSION 7B1-79

5. Install top gear bearing snap ring (9) and counter
front bearing snap ring (7).


Use a pair of snap ring pliers to install the snap
rings to the mainshaft and countershaft.


The snap rings must be fully inserted into the
bearing snap ring groove.
6. Front cover with oil seal (8).
Front Cover Oil Seal Replacement


Remove the oil seal from the front cover.


Apply engine oil to a new oil seal outer
circumference.

Apply recommended grease to the oil seal lip.


Use the oil seal installer 5-8840-0026-0 to install
the oil seal to the front cover.
220R3000020
8. Apply molybdenum disulfide type grease to the
areas as shown in the figure and install shift fork (6).
(Diesel engine, C24NE)
F07L100026
9. Install the fulcrum bridge to the transmission case.
(6VE1)
Torque: 38 N




m (3.9 kg




m/28 lb




ft)
RTW37ASH0002

Legend
(1) Fulcrum bridge

10. Apply molybdenum disulfide type grease to the pin
hole inner circumferences and thrust surfaces.
(6VE1)
11. Attach the shift fork to the fulcrum bridge and insert
the pin from below of the fulcrum bridge. (6VE1)

11A-4 IMMOBILIZER SYSTEM

Diesel Engine With ECM (4JH1-TC/4JA1-TC)

LTW3BALF000201

IMMOBILIZER SYSTEM 11A-5

Diesel Engine With Engine Immobilizer Unit (4JA1-T Mechanical Control Engine)






RAW4B0LF000101

11A-8 IMMOBILIZER SYSTEM

Diesel Engine With ECM (4JH1-TC/4JA1-TC)


RTW4B0LF000101

IMMOBILIZER SYSTEM 11A-9

Diesel Engine With Engine Immobilizer Unit (4JA1-T Mechanical Control Engine)






RAW4B0LF000401