2004 ISUZU TF SERIES battery replacement

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-369
CRANKSHAFT POSITION (CKP)
SENSOR

Location
Right-hand side of the cylinder block.

Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect connector from the CKP sensor.
3. Loosen a bolt and remove the CKP sensor from
the cylinder block.
NOTE:
Use caution to avoid any hot oil that might drip out.




Installation Procedure
1. Install the CKP sensor to the cylinder block.
Before installation, apply small amount of engine
oil to the O-ring.
2. Tighten CKP sensor by a bolt with specified
tightening torque.
Tightening Torque





Bolt: 10N




m (1.0kgf




m).
3. Connect a sensor connector to the CKP sensor.
4. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.

CAMSHAFT POSITION (CMP)
SENSOR

Location
The rear of right bank of the cylinder head.

Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect connector from the CMP sensor.
3. Loosen a bolt and remove the CMP sensor from
the cylinder head.





Installation Procedure
1. Install the CMP sensor to the cylinder head.
Before installation, apply small amount of engine
oil to the O-ring.
2. Tighten CMP sensor by a bolt with specified
tightening torque.
Tightening Torque





Bolt: 10N




m (1.0kgf




m)
3. Connect a sensor connector to the CMP sensor.
4. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.

6E-370 3.5L ENGINE DRIVEABILITY AND EMISSIONS
ENGINE COOLANT TEMPERATURE
(ECT) SENSOR

Location
Installed to the thermostat housing.

Removal Procedure
1. Disconnect the negative battery cable.
2. Drain enough engine coolant so that the coolan
t
level will be below the ECT sensor.
3. Disconnect connector from the ECT sensor.
4. Loosen and remove the ECT sensor from the
thermostat housing.
NOTE:
Cool down the engine before above procedures are
carried out.










Installation Procedure
1. Apply sealer to threads of screw at the ECT
sensor.
2. Tighten the ECT sensor with specified tightening
torque.
Tightening Torque





13N




m (1.3kgf




m)
3. Connect a ECT sensor connector to the ECT
sensor.
4. Fill the engine coolant.
5. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.
Verify no engine coolant leaking from the senso
r
threads after replacement.


MASS AIR FLOW (MAF) SENSOR &
INTAKE AIR TEMPERATURE (IAT)
SENSOR
Location
Installed to the intake duct housing.

Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect a MAF & IAT sensor connector from
the MAF & IAT sensor.
3. Loosen two screws and remove the MAF & IAT
sensor from the intake duct.





Installation Procedure
1. Install the MAF & IAT sensor into intake air duct.
2. Tighten MAF & IAT sensor by two screws.
Tightening Torque : 1.5 N




m (0.15 kgf




m)
3. Connect a sensor connector to the MAF & IAT
sensor.
4. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-371
THROTTLE POSITION SENSOR
(TPS)

Location
Installed on the throttle body.

Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the TPS connector.
3. Loosen two screws and remove TPS from the
throttle body.




Installation Procedure
1. Temporary tighten the TPS by two screws.
2. Connect a TPS connectors to the TPS.
3. Connect the Tech2 to the vehicle.
4. Connect the negative battery cable.
5. Select "Data Display" with the Tech2.
6. Check the throttle position data and adjust the TPS
position.
7. Tighten two screws.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.



IDLE AIR CONTROL (IAC) VALVE

Location
Installed on the throttle body.

Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the IAC valve connector.
3. Loosen two screws and remove IAC valve from
the throttle body.




Cleaning and Inspection
1. Clean the IAC valve O-ring sealing surface, pintle
valve seat and air passage.
2. Use carburetor cleaner and a parts cleaning brush
to remove carbon deposit.
Do not use a cleaner that contain methyl ethyl
ketone. This is an extremely strong solvent and no
t
necessary for this type of deposit.
3. Shiny spots on the pintle are normal and do no
t
indicate misalignment or a bent pintle shaft.
4. Inspect the IAC valve O-ring for cuts, cracks o
r
distortion.

6E-372 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Measurement
In order to install a new IAC valve, messier the distance
between the tip of the pintle and the mounting flange. I
f
that measurement is 28mm (1.1in.) or less, the valve
need no adjustment. If the measurement is greater than
28mm (1.1in.), apply finger pressure and retract the
valve. The force required to retract the pintle on a ne
w
valve will not damage the valve, shaft, or pintle.




28mm(1.1in.)
or less


Installation Procedure
1. Tighten the IAC valve by two screws.
2. Connect a IAC valve connector to the IAC valve.
3. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.


HEATED OXYGEN SENSOR (HO2S)

Location
Installed on the exhaust pipe for each bank.

Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the O2 sensor connector.
3. Loosen and remove the O2 sensor from the
exhaust pipe.



Bank 1 Heated Oxygen Sensor (Right bank)



Bank 2 Heated Oxygen Sensor (Left bank)

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-373
Inspection
 Inspect the louvered end of the sensor for grease,
dirt, excessive carbon build up or othe
r
contamination.
 A special anti-seize compound is used on the O2
sensor threads. This compound consists of glass
breads suspended in a liquid graphite solution.
The graphite burns away with engine heat, but the
glass breads will remain, marking the senso
r
easier to remove.
 New or service sensors will already have the
compound applied to the threads. If a sensor is
removed and is to be reinstalled for any reason,
the threads must have anti-seize compound
applied.


Installation Procedure
1. Install the O2 sensor to the exhaust pipe.
Apply anti-seize compound or the equivalent to the
threads of the oxygen sensor, if necessary.
2. Tighten the O2 sensor with specified tightening
torque.
Tightening Torque





Bolt: 42N




m (4.3kgf




m)
3. Connect a sensor connector to the O2 sensor.
4. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.
Verify no exhaust gas leaking from the senso
r
threads after replacement.



EVAP CANISTER PURGE VALVE
SOLENOID

Location
On the intake manifold.

Removal Procedure
1. Disconenct the negative battery cable.
2. Disconnect a purge solenoid connector from the
purge solenoid.
3. Disconnect two hoses from the purge solenoid
valve.
4. Loosen a bolt and remove the purge solenoid from
the intake manifold.






Installation Procedure
1. Put on the purge solenoid on the intake manifold.
2. Tighten the purge solenoid by a bolt.
3. Connect a connector to the purge solenoid.
4. Connect two hoses to the purge solenoid valve.
5. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.
Verify proper connection of two hoses.

ENGINE COOLING 6B-7
Water Pump
Water Pump and Associated Parts








Legend
1 Water Pump Assembly 2 O-Ring
3 Bolt

2 3 1

















Removal
1. Disconnect battery ground cable.
2. Drain coolant.
3. Disconnect radiator hose (on inlet pipe side).
4. Remove timing belt, refer to "Timing Belt" in this manual.
5. Remove water pump assembly.
Inspection
Make necessary repair and parts replacement if extreme wear
or damage is found during inspection. Should any of the
following problems occur, the entire water pump assembly
must be replaced:

ENGINE COOLING 6B-9
Thermostat





























Removal
1. Disconnect battery ground cable.
2. Drain engine coolant from the radiator and engine.
3. Disconnect radiator hose from the inlet pipe.
4. Remove thermostat housing.
5. Remove thermostat from thermostat housing.
Inspection
Suspend the thermostat in a water-filled container using thin
wire. Place a thermometer next to the thermostat.
Do not directly heat the thermostat.
Gradually increase the water temperature. Stir the water so
that the entire water is same temperature.
Confirm the temperature when the valve first begins to open.
Valve opening temperature 92
 C (197.6
 F)
Confirm the temperature when the valve is fully opened.
Valve full open temperature 107
 C(224.6
 F)
Make necessary repair and parts replacement if extreme wear
or damage is found during inspection.
Installation
1. Before installing thermostat, coat sealing surface with
silicon grease.
2. Install O-ring.
3. Install thermostat housing and tighten bolts to the specified
torque.
Torque: 15 N




m (1.5 kgf




m)
4. Installation rubber hose.
5. Replenish engine coolant (EC).
6. Start engine and check for EC leakage.













Fan Clutch with Cooling Fan
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage or any other abnormal condition are found through
inspection.

Visually inspect for damage, leak (silicon grease) or other
abnormal conditions.
1. Inspection (on-vehicle)
1) Turn the fan clutch by hand when in a low temperature
condition before starting the engine, and confirm that it
can be turned readily.
2) Start the engine to warm it up until the temperature at the
fan clutch portion gets to around 80C. Then stop the
engine and confirm that the fan clutch can be turned with
considerable effort (clutch torque) when turned by hand.

ENGINE FUEL (C24SE) 6C-3


When working on the fuel system, there are several things to
keep in mind:


Any time the fuel system is being worked on, disconnect the
negative battery cable except for those tests where battery
voltage is required.


Always keep a dry chemical (Class B) fire extinguisher near
the work area.

Replace all pipes with the same pipe and fittings that were
removed.

Clean and inspect "O" rings. Replace if required.


Always relieve the line pressure before servicing any fuel
system components.

Do not attempt repairs on the fuel system until you have
read the instructions and checked the pictures relating to
that repair.

Adhere to all Notices and Cautions.
All gasoline engines are designed to use only unleaded
gasoline. Unleaded gasoline must be used for proper emission
control system operation.
Its use will also minimize spark plug fouling and extend engine
oil life. Using leaded gasoline can damage the emission control
system and could result in loss of emission warranty coverage.
All cars are equipped with an Evaporative Emission Control
System. The purpose of the system is to minimize the escape
of fuel vapors to the atmosphere.



Service Precaution
CAUTION:
Always use the correct fastener in the proper location.
When you replace a fastener, use ONLY the exact part
number for that application. ISUZU will call out those
fasteners that require a replacement after removal. ISUZU
will also call out the fasteners that require thread lockers
or thread sealant. UNLESS OTHERWISE SPECIFIED, do
not use supplemental coatings (Paints, greases, or othe
r
corrosion inhibitors) on threaded fasteners or fastene
r
joint interfaces. Generally, such coatings adversely affect
the fastener torque and the joint clamping force, and may
damage the fastener. When you install fasteners, use the
correct tightening sequence and specifications. Following
these instructions can help you avoid damage to parts
and systems.