2004 ISUZU TF SERIES wiring

3B-58 POWER-ASSISTED STEERING SYSTEM

16. Remove steering column cover.
17. Disconnect the wiring harness connectors located
under the steering column.
18. Remove the combination switch assembly with SRS
coil.
NOTE: The SRS coil is a part of the combination switch
assembly, which can not be replaced separately.
Therefore, be sure not to remove the SRS coil from the
combination switch assembly.
430R300014
19. Remove snap ring.
20. Remove cushion rubber.
21. Remove shift lock cable (For A/T).
22. Disconnect the starter switch harness connecto
r
located under the steering column, then remove
lock cylinder assembly.

23.
Apply a setting mark (1) across the universal joint
and transfer gear to reassemble the parts in thei
r
original position, then remove steering column
assembly and second shaft.
NOTE: A setting mark can be easily made if the shaft is
withdrawn a little by loosening the steering shaft
universal joint.



RTW33BSH000501

Inspection
If the abnormal conditions are found through inspection,
replace the steering column assembly.

Column Capsule
Check capsules on steering column bracket assembly;
all must be securely seated in bracket slots and
checked for any loose conditions when pushed or pulled
by hand.
431RW030

POWER-ASSISTED STEERING SYSTEM 3B-59

Check clearance between capsule and bracket. If must
be within 1mm (0.039 in).
431RW031

Column Universal Joint (between the
power steering unit and the steering shaft)
If the resistance is felt when checked by rotate the joint,
replace the lower second steering shaft.

Shaft Universal Joint (between the lower
second steering shaft and the second
steering shaft)
If the resistance is felt when checked by rotate the joint,
replace the second steering shaft assembly.

Tilt Mechanism
Tilt mechanism should moves smoothly.
While locked the tilt mechanism, be sure the steering
column latch securely by pushing the steering wheel
upward and downward.

Installation
1. Align the setting marks on the second steering shaft
and the steering column assembly (applied at
disassembly).
2. Connect the steering column assembly to the second
steering shaft. Tighten the bolts to the specified
torque.
Torque: 26 - 36 N




m (2.7 – 3.7 kg




m/20 - 27 lb ft)
3. Thread the steering column assembly through the
hole in the dashpanel. Temporarily tighten the
steering column and the second steering shaft fixing
bolt.
4. Connect the lower second steering shaft and the
second steering shaft. Tighten the universal joint
bolts to the specified torque.
Torque: 26 - 36 N




m (2.7 – 3.7 kg




m/20 - 27 lb ft)
5. Tighten the steering column fixing bolt (pedal brkt
side) to the specified torque (This bolt was
temporarily tighten in Step 3).
Torque: 18 -23 N




m (1.8 – 2.3 kg




m/13 - 17 lb ft)

6. Tighten the second steering shaft fixing bolt to the
specified torque (This bolt was temporarily tightened
in Step 3)
Torque: 18 -23 N




m (1.8 – 2.3 kg




m/13 - 17 lb ft)
7. Tighten the steering column fixing bolt (dashpanel
side) to the specified torque (This bolt was
temporarily tighten in Step 3).
Torque: 18 -23 N




m (1.8 – 2.3 kg




m/13 - 17 lb ft)
8. Install combination switch and SRS coil assembly.
After installation of combination switch assembly,
connect the combination switch wiring harness
connector and the SRS 2-way connector located
under the steering column.

3C-8 FRONT SUSPENSION


FRONT SUSPENSION
(4




2 Except High Ride Suspension)
CONTENTS

Service Precaution............................................. 3C-8
Shock Absorber ................................................. 3C-9
Shock Absorber and Associated Parts ........... 3C-9
Removal ......................................................... 3C-9
Installation....................................................... 3C-10
Shock Absorber with Coil Spring .................... 3C-12
Stabilizer Bar ..................................................... 3C-15
Stabilizer Bar and Associated Parts ............... 3C-15
Removal ......................................................... 3C-15
Inspection and Repair..................................... 3C-15
Installation....................................................... 3C-16
Knuckle .............................................................. 3C-17
Knuckle and Associated Parts........................ 3C-17
Removal ......................................................... 3C-17
Inspection and Repair..................................... 3C-18
Installation....................................................... 3C-18
Upper Control Arm ............................................. 3C-19
Upper Control Arm and Associated Parts ...... 3C-19
Removal ......................................................... 3C-19
Inspection and Repair..................................... 3C-20
Installation....................................................... 3C-20

Lower Control Arm ............................................. 3C-21
Lower Control Arm and Associated Parts ...... 3C-21
Removal ......................................................... 3C-21
Inspection and Repair..................................... 3C-22
Installation ...................................................... 3C-22
Upper Ball Joint ................................................. 3C-23
Upper Ball Joint and Associated Parts ........... 3C-23
Removal ......................................................... 3C-23
Inspection and Repair..................................... 3C-24
Installation ...................................................... 3C-24
Lower Ball Joint ................................................. 3C-25
Lower Ball Joint and Associated Parts ........... 3C-25
Removal ......................................................... 3C-25
Inspection and Repair..................................... 3C-26
Installation ...................................................... 3C-26
Bump Rubber .................................................... 3C-27
Bump Rubber Joint and Associated Parts...... 3C-27
Removal ......................................................... 3C-27
Inspection and Repair..................................... 3C-27
Installation ...................................................... 3C-27
Special Tools .................................................. 3C-28

Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFE
R
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN
POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM
REPAIRS.



CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, o
r
other corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.

3C-30 FRONT SUSPENSION


FRONT SUSPENSION
(4





2 High Ride Suspension, 4





4)
CONTENTS

Service Precaution............................................. 3C - 29
Shock Absorber ................................................. 3C - 30
Shock Absorber and Associated Parts ........... 3C - 30
Removal ......................................................... 3C - 30
Inspection and Repair..................................... 3C - 30
Installation....................................................... 3C - 30
Stabilizer Bar ..................................................... 3C - 31
Stabilizer Bar and Associated Parts ............... 3C - 31
Removal ......................................................... 3C - 31
Inspection and Repair..................................... 3C - 31
Installation....................................................... 3C - 32
Torsion Bar ........................................................ 3C - 33
Torsion Bar and Associated Parts .................. 3C - 33
Removal ......................................................... 3C - 33
Inspection and Repair..................................... 3C - 34
Installation....................................................... 3C - 34
Knuckle .............................................................. 3C - 36
Knuckle and Associated Parts........................ 3C - 36
Removal ......................................................... 3C - 36
Inspection and Repair..................................... 3C - 38
Installation....................................................... 3C - 38
Upper Control Arm ............................................. 3C - 39
Upper Control Arm and Associated Parts ...... 3C - 39
Removal ......................................................... 3C - 39

Inspection and Repair..................................... 3C - 40
Installation ...................................................... 3C - 41
Lower Control Arm ............................................. 3C - 43
Lower Control Arm and Associated Parts ...... 3C - 43
Removal ......................................................... 3C - 44
Inspection and Repair..................................... 3C - 45
Installation ...................................................... 3C - 45
Upper Ball Joint ................................................. 3C - 47
Upper Ball Joint and Associated Parts ........... 3C - 47
Removal ......................................................... 3C - 47
Inspection and Repair..................................... 3C - 48
Installation ...................................................... 3C - 48
Lower Ball Joint ................................................. 3C - 49
Lower Ball Joint and Associated Parts ........... 3C - 49
Removal ......................................................... 3C - 49
Inspection and Repair..................................... 3C - 50
Installation ...................................................... 3C - 50
Bump Rubber .................................................... 3C - 51
Bump Rubber and Associated Parts .............. 3C - 51
Removal ......................................................... 3C - 51
Inspection and Repair..................................... 3C - 51
Installation ...................................................... 3C - 51
Special Tools .................................................... 3C - 52



Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFE
R
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN
POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM
REPAIRS.



CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, o
r
other corrosion inhibitors) on threaded fasteners o
r
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.

7D-2 TRANSFER CASE

Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFER
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN
POSSIBLE AIR BAG DEPLOYMENT, PERSONAL
INJURY, OR OTHERWISE UNNEEDED SRS SYSTEM
REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or
other corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.

7D1-2 TRANSFER CONTROL SYSTEM

Service Precaution
WARNING:
THIS VEHICLE HAS A SUPPLEMENTAL RESTRAINT
SYSTEM (SRS). REFER TO THE SRS COMPONENT AND
WIRING LOCATION VIEW IN ORDER TO DETERMINE
WHETHER YOU ARE PERFORMING SERVICE ON OR
NEAR THE SRS COMPONENTS OR THE SRS WIRING.
WHEN YOU ARE PERFORMING SERVICE ON OR NEAR
THE SRS COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO FOLLOW
WARNINGS COULD RESULT IN POSSIBLE AIR BAG
DEPLOYMENT, PERSONAL INJURY, OR OTHERWISE
UNNEEDED SRS SYSTEM REPAIRS.

CAUTION:
Always use the correct fastener in the proper location.
When you replace a fastener, use ONLY the exact part
number for that application. ISUZU will call out those
fasteners that require a replacement after removal. ISUZU
will also call out the fasteners that require thread lockers
or thread sealant. UNLESS OTHERWISE SPECIFIED, do
not use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or fastener
joint interfaces. Generally, such coatings adversely affect
the fastener torque and the joint clamping force, and may
damage the fastener. When you install fasteners, use the
correct tightening sequence and specifications. Following
these instructions can help you avoid damage to parts
and systems.

7D1-10 TRANSFER CONTROL SYSTEM

Method of checking the position detection switch harness
Disconnect the vehicle harness connector on the transfer
controller side and the vehicle harness connector on the
transfer actuator side as shown in the wiring diagram, and
check the continuity between the following connector pins and
that there is no continuity between those pins and GND or
power source.
Check that there is continuity between the GND pin and vehicle
GND on the transfer actuator and there is no continuity
between the GND pin and other power source.


RTW47DSF000301

Vehicle harness connector pin No. (connector of mating parts of the harness is shown in this figure)
Name of pin T/F controller side T/F actuator side Remarks
LS1 R-14, 17 5
LS2 R-14, 6 4
LS3 R-14, 15 7
LS4 R-14, 14 6
GND R-15, 1, 9 8

7D1-48 TRANSFER CONTROL SYSTEM
From 4H to 4L; Even after the correction step 3-3(*), 4Lo indicator blinks at 4Hz
Step Action Yes No
1 Is the ignition switch ON? Turn it OFF once. Go to step 2.
2 Turn ON the ignition switch and
check the valve. Do not start
the engine.
Has the valve check for 2
seconds been completed
normally? Go to step 3. Refer to the paragraph about the
indicator when it does not react
when shifted from 2H to 4H.
After taking the remedy, trace
this chart from the beginning.
3 Shift to 2H.
Can be shifted to 2H and then to
4H? Go to step 4. Refer to the paragraph about
shifting from 2H to 4H.
In particular, check if not at the
Check4WD condition, return to
this chart and trace it from the
beginning.
4 Set to N position in case of AT
and set to the neutral position in
case of MT and check if the
lamp blinks at 4Hz after
operation.
Failed T/M position switch and
harness (failure of TM1 and TM2
harness and their related
switches shown in the figure).
Incorrect wiring.
Repair as required and trace this
chart from the beginning. Shift back to 4H and go to step 5.
5 Start the engine and travel the
vehicle.
Does the speedometer run at
this time? Go to step 6. Failure of speed sensor or
disconnection or short of harness
(for the meter).
After repairing, trace this chart
from the beginning.
6 Check the harness between the
transfer controller and speed
sensor.
(Check the engine rotation
detection harness at the same
time.)
Is any trouble noticed? Failed harness between the
transfer controller and speed
sensor.
After repairing, trace this chart
from the beginning.
(Repair the engine rotation
detection unit, if required.) Go to step 7.
7 Travel the vehicle several
meters, stop it, meet the
permission requirements for
operation limits.
Did you wait for several seconds
after the requirements were
met? Failed controller.
Replace the controller and trace
this chart from the beginning. You did not wait for enough time.
Optimum waiting time is 1
second or maximum 3 minutes
depending on the previous
conditions.
Refer to the paragraph about
operation without failure.
*Before determining a trouble (Non-trouble mode)