2004 ISUZU TF SERIES change wheel

6E–66 4JA1/4JH1 ENGINE DRIVEABILITY AND EMISSIONS
Throttle Position Sensor (TPS)
The TPS is a potentiometer connected to throttle shaft
on the throttle body. It is installed to the main TPS and
idle switch.
The engine control module (ECM) monitors the voltage
on the signal line and calculates throttle position. As the
throttle valve angle is changed when accelerator pedal
moved. The TPS signal also changed at a moved
throttle valve. As the throttle valve opens, the output
increases so that the output voltage should be high.
The engine control module (ECM) calculates fuel
delivery based on throttle valve angle.
Crankshaft Position (CKP) Sensor
The CKP sensor is located on top of the flywheel
housing of the flywheel and fix ed with a bolt.
The CKP sensor is of the magnet coil type. The
inductive pickup sensors four gaps in the flywheel
ex citer ring and is used to determine the engine speed
and engine cylinder top dead center (TDC). (1) Throttle Position Sensor (TPS)
(2) Idle Switch

1 2
Characteristic of TPS -Reference-
0 0.51 1.52 2.53 3.54 4.5
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
Pedal Position (%) (Tech2 Readin
g
Output Voltage (V)
(1) Crankshaft Position (CKP) Sensor
(2) Fly wheel with sensor slot

1 2

6C-12 ENGINE FUEL (6VE1 3.5L)
Removal
CAUTION: When repair to the fuel system has been
completed, start engine and check the fuel system
for loose connection or leakage. For the fuel system
diagnosis, see Section “Driveability and Emission".
1. Disconnect battery ground cable.
2. Loosen slowly the fuel filler cap.
NOTE: To prevent spouting out fuel to change the
pressure in the fuel tank.
NOTE: Cover opening of the filler neck to prevent any
dust entering.
3. Jack up the vehicle.
4. Support underneath of the fuel tank with a lifter.
5. Remove the inner liner of the wheel house on rea
r
left side.
6. Remove fasten bolt to the filler neck from the
body.
7. Disconnect the quick connector (8) into the fuel
tube from the fuel pipe and the evapo tube from
evapo joint connector.
NOTE: Cover the quick connector to prevent any dus
t
entering and fuel leaking.
NOTE: Refer to “Fuel Tube/Quick Connector Fittings” in
this section when performing any repairs.
8. Remove fasten bolt (1) to the tank band and the
tank band (2).
9. Disconnect the pump and sender connector on the
fuel pump and remove the harness from weld clip
on the fuel tank.
10. Lower the fuel tank (6).
NOTE: When the fuel tank is lowered from the vehicle,
don’t scratch each hose and tube by around other pars.


Installation
1. Rise the fuel tank into position.
NOTE: Ensure hoses and tubes do not foul on othe
r
component.
2. Connect the pump and sender connector to the
fuel pump and install harness to into the plastic clip
welded to the top of the fuel tank..
NOTE: The connector must be certainly connected
against stopper.
Ensure tank band anchor mates with guide hole on
frame.
3. Install the tank band to fasten bolt.
Torque: 68 N




m (6.9kg




m/50 lb ft)
NOTE: The anchor of the tank band must be certainly
installed to guide hole on frame.
4. Connect the quick connector from the fuel tube to
the fuel pipe and the evapo tube from evapo join
t
connector.
NOTE: Pull off the left checker into the fuel pipe.
NOTE: Refer to “Fuel Tube/Quick Connector Fittings” in
this section when performing any repairs.
5. Install the filler neck to the body by bolt.
6. Install the inner liner of the wheel house on rea
r
side.
7. Remove lifter to support underneath of the fuel
tank.
8. Put back the vehicle.
9. Tigten the filler cap until at least three clicks are
heard.
10. Connect the battery ground cable.

6E-70 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Fuel Quality
Fuel quality is not a new issue for the automotive
industry, but its potential for turning on the MIL (“Check
Engine" lamp) with OBD systems is new.
Fuel additives such as “dry gas" and “octane
enhancers" may affect the performance of the fuel. The
Reed Vapor Pressure of the fuel can also create
problems in the fuel system, especially during the spring
and fall months when severe ambient temperature
swings occur. A high Reed Vapor Pressure could sho
w
up as a Fuel Trim DTC due to excessive canister
loading. High vapor pressures generated in the fuel
tank can also affect the Evaporative Emission
diagnostic as well.
Using fuel with the wrong octane rating for your vehicle
may cause driveability problems. Many of the majo
r
fuel companies advertise that using “premium" gasoline
will improve the performance of your vehicle. Mos
t
premium fuels use alcohol to increase the octane rating
of the fuel. Although alcohol-enhanced fuels may raise
the octane rating, the fuel's ability to turn into vapor in
cold temperatures deteriorates. This may affect the
starting ability and cold driveability of the engine.
Low fuel levels can lead to fuel starvation, lean engine
operation, and eventually engine misfire.
Non-OEM Parts
All of the OBD diagnostics have been calibrated to run
with OEM parts.
Aftermarket electronics, such as cellular phones,
stereos, and anti-theft devices, may radiate EMI into the
control system if they are improperly installed. This may
cause a false sensor reading and turn on the MIL
(“Check Engine" lamp).
Environment
Temporary environmental conditions, such as localized
flooding, will have an effect on the vehicle ignition
system. If the ignition system is rain-soaked, it can
temporarily cause engine misfire and turn on the MIL
(“Check Engine" lamp).
Vehicle Marshaling
The transportation of new vehicles from the assembly
plant to the dealership can involve as many as 60 key
cycles within 5Km miles of driving. This type o
f
operation contributes to the fuel fouling of the spark
plugs and will turn on the MIL (“Check Engine" lamp).

Poor Vehicle Maintenance
The sensitivity of OBD diagnostics will cause the MIL
(“Check Engine" lamp) to turn on if the vehicle is no
t
maintained properly. Restricted air filters, fuel filters,
and crankcase deposits due to lack of oil changes o
r
improper oil viscosity can trigger actual vehicle faults
that were not previously monitored prior to OBD. Poo
r
vehicle maintenance can not be classified as a
“non-vehicle fault", but with the sensitivity of OBD
diagnostics, vehicle maintenance schedules must be
more closely followed.
Severe Vibration
The Misfire diagnostic measures small changes in the
rotational speed of the crankshaft. Severe driveline
vibrations in the vehicle, such as caused by an
excessive amount of mud on the wheels, can have the
same effect on crankshaft speed as misfire.
Related System Faults
Many of the OBD system diagnostics will not run if the
ECM detects a fault on a related system or component.
One example would be that if the ECM detected a
Misfire fault, the diagnostics on the catalytic converte
r
would be suspended until Misfire fault was repaired. If
the Misfire fault was severe enough, the catalytic
converter could be damaged due to overheating and
would never set a Catalyst DTC until the Misfire faul
t
was repaired and the Catalyst diagnostic was allowed to
run to completion. If this happens, the customer may
have to make two trips to the dealership in order to
repair the vehicle.
Maintenance Schedule
Refer to the Maintenance Schedule.
Visual/Physical Engine Compartment
Inspection
Perform a careful visual and physical engine
compartment inspection when performing any
diagnostic procedure or diagnosing the cause of an
emission test failure. This can often lead to repairing a
problem without further steps. Use the following
guidelines when performing a visual/physical inspection:

Inspect all vacuum hoses for punches, cuts,
disconnects, and correct routing.

Inspect hoses that are difficult to see behind othe
r
components.

Inspect all wires in the engine compartment fo
r
proper connections, burned or chafed spots, pinched
wires, contact with sharp edges or contact with ho
t
exhaust manifolds or pipes.

6C-14 ENGINE FUEL (C24SE)
Removal
CAUTION: When repair to the fuel system has been
completed, start engine and check the fuel system
for loose connection or leakage. For the fuel system
diagnosis, see Section “Driveability and Emission".
1. Disconnect battery ground cable.
2. Loosen slowly the fuel filler cap.
NOTE: To prevent spouting out fuel to change the
pressure in the fuel tank.
NOTE: Cover opening of the filler neck to prevent any
dust entering.
3. Jack up the vehicle.
4. Support underneath of the fuel tank with a lifter.
5. Remove the inner liner of the wheel house on rea
r
left side.
6. Remove fasten bolt to the filler neck from the
body.
7. Disconnect the quick connector (8) into the fuel
tube from the fuel pipe and the evapo tube from
evapo joint connector.
NOTE: Cover the quick connector to prevent any dus
t
entering and fuel leaking.
NOTE: Refer to “Fuel Tube/Quick Connector Fittings” in
this section when performing any repairs.
8. Remove fasten bolt (1) to the tank band and the
tank band (2).
9. Disconnect the pump and sender connector on the
fuel pump and remove the harness from weld clip
on the fuel tank.
10. Lower the fuel tank (6).
NOTE: When the fuel tank is lowered from the vehicle,
don’t scratch each hose and tube by around other pars.


Installation
1. Rise the fuel tank into position.
NOTE: Ensure hoses and tubes do not foul on othe
r
component.
2. Connect the pump and sender connector to the
fuel pump and install harness to into the plastic clip
welded to the top of the fuel tank..
NOTE: The connector must be certainly connected
against stopper.
Ensure tank band anchor mates with guide hole on
frame.
3. Install the tank band to fasten bolt.
Torque: 68 N




m (6.9kg




m/50 lb ft)
NOTE: The anchor of the tank band must be certainly
installed to guide hole on frame.
4. Connect the quick connector from the fuel tube to
the fuel pipe and the evapo tube from evapo join
t
connector.
NOTE: Pull off the left checker into the fuel pipe.
NOTE: Refer to “Fuel Tube/Quick Connector Fittings” in
this section when performing any repairs.
5. Install the filler neck to the body by bolt.
6. Install the inner liner of the wheel house on rea
r
side.
7. Remove lifter to support underneath of the fuel
tank.
8. Put back the vehicle.
9. Tigten the filler cap until at least three clicks are
heard.
10. Connect the battery ground cable.

0B-4 MAINTENANCE AND LUBRICATION




I : Inspect and correct or replace as necessary A : Adjust
R : Replace or change T : Tighten to specified torque L : Lubricate
SERVICE INTERVAL:
1,000 km 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100(Use odometer reading
1,000 miles 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60or months whichever
comes fi rst)
or months 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
SERVICE BRAKES Brake fluid I - - I - - - I - - - I - - - I - - - I Brake sy stem for fluid l eakage I I I I I I I I I I I I I I I I I I I I Brake functi on I I I I I I I I I I I I I I I I I I I I * Rear brake lining and drum wear - I - I - I - I - I - I - I - I - I - I * Front disc brake pads and discs - I - I - I - I - I - I - I - I - I - I Brake pedal travel and free play I I I I I I I I I I I I I I I I I I I I Pipes and hoses loose connections
or damage I I - I - I - I - I - I - I - I - I - I
PARKING BRAKE Parki ng brake functi on I I I I I I I I I I I I I I I I I I I I Parki ng brake l ever travel I I I I I I I I I I I I I I I I I I I I Cables for looseness or damage
and guide for damage I I I I I I I I I I I I I I I I I I I I
Ratchet for wear or damage - I - I - I - I - I - I - I - I - I - I SUSPENSION Leaf / Coil / Torsion bar springs for
damage I I - I - I - I - I - I - I - I - I - I
Mount for l ooseness or damage I I - I - I - I - I - I - I - I - I - I Shock absorbers for oil leakage - I - I - I - I - I - I - I - I - I - I Shock absorbers mount for
looseness - I - I - I - I - I - I - I - I - I - I
Rubber bushes of suspension wear
or damage - I - I - I - I - I - I - I - I - I - I
Spring action for loss of balance
due to weakening - - - I - - - I - - - I - - - I - - - I
Joint ball rubber boot for damage - I - I - I - I - I - I - I - I - I - I WHEELS Wheel nuts T T - T - T - T - T - T - T - T - T - T Wheel disc for damage I I - I - I - I - I - I - I - I - I - I Hub bearing grease - - - - - R - - - - - R - - - - - R - - Front and rear hub bearing for
looseness - I - I - I - I - I - I - I - I - I - I
Tire pressure and damage I I - I - I - I - I - I - I - I - I - I Tire rotation (Rotate as required) OTHERS Bolts and nuts on chassis and body I I - I - I - I - I - I - I - I - I - I Lube front free – wheding hubs - - - - - L - - - - - L - - - - - L - -

0B-6 MAINTENANCE AND LUBRICATION




I : Inspect and correct or replace as necessary A : Adjust
R : Replace or change T : Tighten to specified torque L : Lubricate
SERVICE INTERVAL:
1,000 km 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100(Use odometer reading or
1,000 miles 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60months whichever comes
fi rst)
or months 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
PROPELLER SHAFT Loose connections (4JH1-TC) - I - I - I - I - I - I - I - I - I - I Loose connections (4JA1-TC) - - I - - I - - I - - I - - I - - I - - * Universal joints and splines for wear (4JH1-TC) - I - I - I - I - I - I - I - I - I - I * Universal joints and splines for wear (4JA1-TC) - - I - - I - - I - - I - - I - - I - - 4WD Universal joints and sliding
sleeve (4JH1-TC) - L - L - L - L - L - L - L - L - L - L FRONT AND REAR AXLE * Differential gear oil (Front and rear) (4JH1-TC) - R - I - - - R - - - I - - - R - - - I * Differential gear oil (Front and rear) (4JA1-TC) - - R - - I - - R - - I - - R - - I - - Oil leakage (4JH1-TC) I I I I I I I I I I I I I I I I I I I I Oil leakage (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Shift on the fly system Gear oil (4JH1-TC) I - - I - - - I - - - I - - - I - - - I Gear oil (4JA1-TC) - - - - - - - - I - - - - - - - - I - - Front axle shaft rubber boot for
damage (4JH1-TC) - - - I - - - I - - - I - - - I - - - I Front axle shaft rubber boot for
damage (4JA1-TC) - - - - - - - - I - - - - - - - - I - - Axle case for distortion or damage (4JH1-TC) - - - I - - - I - - - I - - - I - - - I Axle case for distortion or damage (4JA1-TC) - - - - - - - - I - - - - - - - - I - - Axle shafts for distortion or damage (4JH1-TC) - - - I - - - I - - - I - - - I - - - I Axle shafts for distortion or damage (4JA1-TC) - - - - - - - - I - - - - - - - - I - - STEERING Power steering fluid (4JH1-TC) I I I I I I R I I I I I I R I I I I I I Power steering fluid (4JA1-TC) - - - - - - - - - - - I - - - - - - - - Oil leakage (4JH1-TC) I I I I I I I I I I I I I I I I I I I I Oil leakage (4JA1-TC) - - I - - R - - I - - R - - I - - R - - * Steering system for looseness or
damage (4JH1-TC) - I - I - I - I - I - I - I - I - I - I * Steering system for looseness or
damage (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Power steering hose (4JH1-TC) - I - I - I - I - I - I - R - I - I - I Power steering hose (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Steering wheel play (4JH1-TC) I I I I I I I I I I I I I I I I I I I I Steering wheel play (4JA1-TC) - - I - - I - - I - - R - - I - - I - - Steering function (4JH1-TC) I I I I I I I I I I I I I I I I I I I I Steering function (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Right and left turning radius (4JH1-TC) - - - I - - - I - - - I - - - I - - - I Right and left turning radius (4JA1-TC) - - - - - - - - I - - - - - - - - I - - Wheel alignment (4JH1-TC) - - - I - - - I - - - I - - - I - - - I Wheel alignment (4JA1-TC) - - - - - - - - I - - - - - - - - I - - Joint ball for oil leakage or damage (4JH1-TC) - I - I - I - I - I - I - I - I - I - I Joint ball for oil leakage or damage (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Joint ball rubber boot for damage (4JH1-TC) - I - I - I - I - I - I - I - I - I - I Joint ball rubber boot for damage (4JA1-TC) - - I - - I - - I - - I - - I - - I - -

0B-8 MAINTENANCE AND LUBRICATION




I : Inspect and correct or replace as necessary A : Adjust
R : Replace or change T : Tighten to specified torque L : Lubricate
SERVICE INTERVAL:
1,000 km 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100(Use odometer reading or
1,000 miles 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60months whichever comes
fi rst)
or months 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
WHEELS Wheel nuts (4JH1-TC) T T - T - T - T - T - T - T - T - T - T Wheel nuts (4JA1-TC) - - T - - T - - T - - T - - T - - T - - Wheel disc for damage (4JH1-TC) I I - I - I - I - I - I - I - I - I - I Wheel disc for damage (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Hub bearing grease (4JH1-TC) - - - - - R - - - - - R - - - - - R - - Hub bearing grease (4JA1-TC) - - - - - R - - - - - R - - - - - R - - Front and rear hub bearings for
looseness (4JH1-TC) - I - I - I - I - I - I - I - I - I - I Front and rear hub bearings for
looseness (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Tire pressure and damage (4JH1-TC) I I - I - I - I - I - I - I - I - I - I Tire pressure and damage (4JA1-TC) - - I - - I - - I - - I - - I - - I - - OTHERS Bolts and nuts on chassis and body (4JH1-TC) I I - I - I - I - I - I - I - I - I - I Bolts and nuts on chassis and body (4JA1-TC) - - I - - I - - I - - I - - I - - I - - Lube front free - wheeling hubs - - - - - L - - - - - L - - - - - L - -

MAINTENANCE AND LUBRICATION 0B-9


Diesel Engine model (Engine oil that meet or exceeds ACEA B3 specification)
I : Inspect and correct or replace as necessary A : Adjust
R : Replace or change T : Tighten to specified torque L : Lubricate


SERVICE INTERVAL:
1,000 km 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100(Use odometer reading or
1,000 miles 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60months whichever comes
fi rst)
or months 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 102 108 114 120
DIESEL ENGINE * Engine oil - - - R - - - R - - - R - - - R - - - R* Engine oil filter - - - R - - - R - - - R - - - R - - - ROil leakage and contamination - - - I - - - I - - - I - - - I - - - I Idling speed and acceleration - - - I - - - I - - - I - - - I - - - I Fan belt tension and damage - - - I - - - I - - - I - - - I - - - I Exhaust system - - - I - - - I - - - I - - - I - - - I All hoses and pipes in engine
compartment for clog of damage
-
-
-
I
-
-
-
I
-
-
-
I
-
-
-
I
-
-
-
I
Valve clearance - - - A - - - A - - - A - - - A - - - A * Air cleaner element - - - I - - - I - - - R - - - I - - - I Fuel filter - - - - - - - - - - - R - - - - - - - - Engine coolant concentration - - - I - - - I - - - I - - - I - - - I Cooling system for water leakage - - - I - - - I - - - I - - - I - - - I CLUTCH Clutch fluid - - - I - - - I - - - I - - - I - - - I Clutch pedal travel and play - - - I - - - I - - - I - - - I - - - I TRANSMISSION OR TRANSMISSION
WITH TRANSFER CASE
* Manual transmission with fluid - - - R - - - I - - - R - - - I - - - I * Transfer case oil - - - R - - - I - - - R - - - I - - - I Oil leakage - - - I - - - I - - - I - - - I - - - I Gear control mechanism for
looseness - - - - - - - - - - - I - - - - - - - -
* AT Automatic transmissi on fl ui d - - - - - - - - - - - I - - - - - - - - * AT Transfer case oil - - - R - - - I - - - R - - - I - - - R PROPELLER SHAFT Loose connections - - - I - - - I - - - I - - - I - - - I * Universal joints and splines for wear - - - I - - - I - - - I - - - I - - - I 4WD Universal joints and sliding
sleeve - - - L - - - L - - - L - - - L - - - L
FRONT AND REAR AXLE * Differential gear oil (Front and rear) - - - R - - - I - - - R - - - I - - - ROil leakage - - - I - - - I - - - I - - - I - - - I Shift on the fly system Gear oi l - - - - - - - - - - - I - - - - - - - - Front axle shaft rubber boot for
damage - - - - - - - - - - - I - - - - - - - I
Axle case for distortion or damage - - - - - - - - - - - I - - - - - - - I Axle shafts for distortion or damage - - - - - - - - - - - I - - - - - - - I STEERING Power steering fluid - - - I - - - R - - - I - - - R - - - I Oil leakage - - - I - - - I - - - I - - - I - - - I * Steering system for looseness or
damage - - - I - - - I - - - I - - - I - - - I
Power steering hose - - - I - - - I - - - I - - - R - - - I Steering wheel play - - - I - - - I - - - I - - - I - - - I Steeri ng function - - - I - - - I - - - I - - - I - - - I Right and left turning radius - - - - - - - - - - - I - - - - - - - - Wheel al i gnment - - - - - - - - - - - I - - - - - - - - Joi nt ball for oil l eakage or damage - - - I - - - I - - - I - - - I - - - I Joi nt ball rubber boot for damage - - - I - - - I - - - I - - - I - - - I