2004 INFINITI QX56 turn signal

AT-230
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: August 20072004 QX56
9. DETECT MALFUNCTIONING ITEM

Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to AT-68,
"Symptom Chart" (Symptom No.17).
OK or NG
OK >> GO TO 7.
NG >> Repair or replace damaged parts.
Vehicle Does Not Decelerate By Engine BrakeUCS002J 2
SYMPTOM:
No engine brake is applied when the gear is shifted from the 22 to 11 .
DIAGNOSTIC PROCEDURE
1. CHECK SELF-DIAGNOSIS RESULTS
Perform self-diagnosis.
Do the self-diagnosis results indicate PNP switch, ATF pressure switch 5?
YES >> Check the malfunctioning system. Refer to AT-109, "DTC P0705 PARK/NEUTRAL POSITION
SWITCH" , AT-181, "DTC P1845 ATF PRESSURE SWITCH 5" .
NO >> GO TO 2.
2. CHECK 1ST POSITION SWITCH CIRCUIT
With CONSULT-II
1. Turn ignition switch “ON”.
2. Select "ECU INPUT SIGNALS" in "DATA MONITOR" mode for
"A/T" with CONSULT-II.
3. Read out "OVERDRIVE SW" switch moving selector lever to
each position.
Without CONSULT-II
1. Turn ignition switch “ON”. (Do not start engine)
2. Check voltage between A/T device harness connector terminal
and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace damaged parts.
Monitor item Condition Display value
1 POSITION SWWhen setting the selector
lever to "1" position.ON
When setting selector
lever to other positions.OFF
LCIA0339E
Item Connector No.Te r m i n a l N o .
(Wire color)ConditionData
(Approx.)
1st position
switchM2037 (Y/G) -
GroundWhen setting
the selector
lever to "1"
position.0V
When setting
selector lever
to other posi-
tions.Battery volt-
age
LCIA0341E

AT-238
A/T SHIFT LOCK SYSTEM
Revision: August 20072004 QX56
Shift Lock Control Unit Reference ValuesUCS002J 9
SHIFT LOCK HARNESS CONNECTOR TERMINALS LAYOUT
SHIFT LOCK CONTROL UNIT INSPECTION TABLE
Data are reference values.
NOTE:
Confirm that the pointer swings only momentarily because the output time is so short. If the inspection is done with an oscilloscope, it
should be observed that the power source voltage lasts for 3.5 to 10 ms.
LCIA0327E
TER-
MINAL
NO.WIRE
COLORITEM CONDITIONVOLTAGE
(V)
1 Y/R Power sourceIgnition switch: “ON” Battery voltage
Ignition switch: “OFF” Battery voltage
2L/R Detention switch
(for key)When selector lever is not in "P" position with key inserted. Battery voltage
Except the above Approx. 0V
3GRDetention switch
(for shift)When selector lever is not in "P" position Battery voltage
Except the above Approx. 0V
4 R/G Stop lamp switchWhen brake pedal is depressed Battery voltage
When brake pedal is released Approx. 0V
5W/RVehicle speed sig-
nal——
——
6 G/R Ignition signalIgnition switch: “OFF” Approx. 0V
Ignition switch: “ON” Battery voltage
7 R/W Shift lock solenoidWhen brake pedal is depressed with ignition switch "ON". Approx. 0V
When brake pedal is depressed. Battery voltage
8 B Ground — Approx. 0V
9 G/W Key lock solenoidWhen the selector lever is set to a position other than the “P”
position, and the key switch is turned from “ON” to “OFF”Battery voltage for
approx. 0.1 sec.
(Note)
Except the above Approx. 0V
10 W/G Key unlock solenoidWhen ignition switch is not in "ON” position with key inserted.Battery voltage for
approx. 0.1 sec.
(Note)
Except the above Approx. 0V

ATC-24
AIR CONDITIONER CONTROL
Revision: August 20072004 QX56
AIR CONDITIONER CONTROLPFP:27500
DescriptionEJS002BW
The front air control provides automatic regulation of the vehicle's interior temperature. The system is based
on the driver's and passenger's selected "set temperature", regardless of the outside temperature changes.
This is done by utilizing a microcomputer that is part of the front air control, which receives input signals from
the following five sensors:

Ambient sensor

In-vehicle sensor

Intake sensor

Optical sensor (one sensor for driver and passenger side)

PBR (position balanced resistor)
The front air control uses these signals (including the set temperature) to automatically control:

Outlet air volume

Air temperature

Air distribution
The front air control also provides separate regulation of the vehicle's interior temperature for the rear passen-
ger area. The system is based on the temperature and rear blower settings selected on the front air control
rear fan switch (front) and rear temperature/mode dial (front), or from the rear fan switch (rear) and rear tem-
perature/mode dial (rear) on the rear air control, when the rear fan switch (front) is set to the rear (R) position.
The front air control or rear air control is used to select:

Outlet air volume

Air temperature/mode distribution
OperationEJS002BX
AIR MIX DOORS CONTROL
The air mix doors are automatically controlled so that in-vehicle temperature is maintained at a predetermined
value by the temperature setting, ambient temperature, in-vehicle temperature and amount of sunload.
FAN SPEED CONTROL
Blower speed is automatically controlled based on temperature setting, ambient temperature, in-vehicle tem-
perature, intake temperature, amount of sunload and air mix door position.
When AUTO switch is pressed, the blower motor starts to gradually increase air flow volume (if required).
When engine coolant temperature is low, the blower motor operation is delayed to prevent cool air from flow-
ing.
INTAKE DOOR CONTROL
The intake door is automatically controlled by the temperature setting, ambient temperature, in-vehicle tem-
perature, intake temperature, amount of sunload and ON-OFF operation of the compressor.
MODE DOOR CONTROL
The mode door is automatically controlled by the temperature setting, ambient temperature, in-vehicle temper-
ature, intake temperature and amount of sunload.
DEFROSTER DOOR CONTROL
The defroster door is controlled by turning the defroster dial to front defroster.

AIR CONDITIONER CONTROL
ATC-25
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
MAGNET CLUTCH CONTROL
When the A/C or DEF switch is activated, the front air control outputs a compressor ON signal to the BCM.
Upon receiving this input, the BCM sends a compressor ON signal to the ECM via CAN communication lines.
The ECM then judges whether the compressor can be turned ON, based on each sensor status (refrigerant
pressure sensor signal, throttle angle sensor, etc.). If it determines the compressor can be turned ON, a com-
pressor ON signal is sent to the IPDM E/R via CAN communication lines.
Upon receipt of a compressor ON signal, the IPDM E/R turns ON the A/C relay which engages the magnet
clutch and operates the A/C compressor.
SELF-DIAGNOSTIC SYSTEM
A self-diagnostic system is built into the front air control to quickly locate the cause of symptoms. Refer to
ATC-53, "
A/C System Self-diagnosis Function"
WJIA0751E

TROUBLE DIAGNOSIS
ATC-33
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
TROUBLE DIAGNOSISPFP:00004
CONSULT-II Function (BCM)EJS002C4
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II BASIC OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect CONSULT-II and CON-
SULT-II CONVERTER to the data link connector, then turn the
ignition switch ON.
2. Touch “START (NISSAN BASED VHCL)”.
3. Touch “BCM” on “SELECT SYSTEM” screen. If “BCM” is not
indicated, go to GI-39, "
CONSULT-II Data Link Connector (DLC)
Circuit" .
BCM diagnostic
test itemDiagnostic mode Description
Inspection by partWORK SUPPORTSupports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR Displays BCM input/output data in real time.
ACTIVE TEST Operation of electrical loads can be checked by sending drive signal to them.
SELF-DIAG RESULTS Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR The result of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER BCM part number can be read.
CONFIGURATION Performs BCM configuration read/write functions.
BBIA0369E
BCIA0029E
BCIA0030E

ATC-54
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
Using Confirmation/Adjustment Mode (NAVI)
NOTE:
Ambient temperature must be at least 10° C (50° F) to run self-diagnosis.
1. Start engine.
2. Turn the audio system off.
3. While pressing the "PAUSE/MUTE" button, turn the volume con-
trol dial clockwise or counterclockwise for 30 clicks or more.
(When the self diagnosis mode is started, a short beep will be
heard.)

Shifting from current screen to previous screen is performed
by pressing "PREV" button.
4. The initial self-diagnosis screen will be shown, and items "Self-
Diagnosis (DCU)", "Self-Diagnosis (NAVI)", "Confirmation/
Adjustment" and "CAN DIAG SUPPORT MONITOR" will
become selective.
5. When "Confirmation/Adjustment" is selected on the initial self-
diagnosis screen, the operation will enter CONFIRMATION/
ADJUSTMENT mode. In this mode, check and adjustment of
each item will become possible.
6. The initial trouble diagnosis screen will be shown, and items
"display Diagnosis", "Vehicle Signals", "Auto Climate Control"
and "Navigation" will become selective.
7. Select the "Auto Climate Control" switch on "CONFIRMATION/
ADJUSTMENT" screen to display the "Auto Climate Control"
diagnosis screen to begin diagnosis The front blower speed indi-
cation bars will flash and the ambient temperature display will
indicate 0° during the self-diagnosis. Fault codes (if any are
present) will be displayed in the ambient temperature display area. Refer to ATC-55, "
SELF-DIAGNOSIS
CODE CHART" .
WKIA1504E
SKIA4207E
SKIA4220E

TROUBLE DIAGNOSIS
ATC-65
C
D
E
F
G
H
I
K
L
MA
B
AT C
Revision: August 20072004 QX56
COMPONENT DESCRIPTION
Mode Door Motor
The mode door motor is attached to the heater & cooling unit. It
rotates so that air is discharged from the outlet as indicated by the
front air control. Motor rotation is conveyed to a link which activates
the mode door.
DIAGNOSTIC PROCEDURE FOR MODE DOOR MOTOR
1. CHECK RESULT FROM FRONT AIR CONTROL SELF-DIAGNOSIS
Self-diagnosis code 92 is present. Refer to ATC-53, "
A/C System Self-diagnosis Function" .
YES or NO
YES >> GO TO 2.
NO >> GO TO 3.
2. CHECK POWER SUPPLY AND GROUND CIRCUITS FOR MODE DOOR MOTOR
1. Turn ignition switch OFF.
2. Disconnect front air control connector M49 and mode door
motor connector M142.
3. Check continuity between front air control harness connector
M49 terminal 5 (BR/W) and mode door motor connector M142
terminal 5 (BR/W) and between front air control harness con-
nector M49 terminal 6 (P/L) and mode door motor connector
M142 terminal 6 (P/L).
OK or NG
OK >> Replace mode door motor. Refer to ATC-152, "Removal and Installation" .
NG >> Repair or replace harness as necessary.
3. CHECK PBR REFERENCE SIGNAL VOLTAGE
1. Disconnect mode door motor connector M142.
2. Turn ignition switch ON.
3. Check voltage between mode door motor harness connector
M142 terminal 3 (Y) and ground.
OK or NG
OK >> GO TO 5.
NG >> GO TO 4.
WJIA0587E
5 - 5 : Continuity should exist.
6 - 6 : Continuity should exist.
LJIA0027E
3 - Ground : Approx. 5V
LJIA0028E

ATC-66
TROUBLE DIAGNOSIS
Revision: August 20072004 QX56
4. CHECK PBR REFERENCE VOLTAGE CIRCUIT BETWEEN MODE DOOR AND FRONT AIR CONTROL
1. Turn ignition switch OFF.
2. Disconnect front air control connector M49.
3. Check continuity between mode door motor harness connector
M142 terminal 3 (Y) and front air control harness connector M49
terminal 2 (Y).
OK or NG
OK >> Replace front air control. Refer to ATC-135, "FRONT
AIR CONTROL" .
NG >> Repair or replace harness as necessary.
5. CHECK PBR GROUND REFERENCE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front air control connector M49.
3. Check continuity between mode door motor harness connector
M142 terminal 1 (P) and front air control harness connector M49
terminal 15 (P).
OK or NG
OK >> GO TO 6.
NG >> Repair or replace harness as necessary.
6. CHECK PBR FEEDBACK SIGNAL
1. Reconnect front air control connector and mode door motor connector.
2. Turn ignition switch ON.
3. Check voltage between front air control harness connector M49
terminal 16 (GR) and ground.
4. Press mode switch through all modes.
OK or NG
OK >> Replace front air control. Refer to ATC-135, "FRONT
AIR CONTROL" .
NG >> GO TO 7.
7. CHECK PBR FEEDBACK CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect mode door motor connector M142 and front air con-
trol harness connector M49.
3. Check continuity between mode door motor harness connector
M142 terminal 2 (GR) and front air control harness connector
M49 terminal 16 (GR).
OK or NG
OK >> Replace mode door motor. Refer to ATC-152, "MODE
DOOR MOTOR" .
NG >> Repair or replace harness as necessary.3 - 2 : Continuity should exist.
LJIA0029E
1 - 15 : Continuity should exist.
LJIA0031E
16 - Ground : Approx. 0 - 5V
LJIA0032E
2 - 16 : Continuity should exist.
LJIA0034E