2004 INFINITI QX56 torque

ASSEMBLY
AT-317
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
b.4WD models
i. Install gasket to transmission case.
CAUTION:

Do not reuse gasket.

Complete remove all moisture, oil and old gasket, etc.
From the transmission case and adapter case assembly
mounting surfaces.
ii. Install adapter case assembly to transmission case.
iii. Install bracket.
iv. Tighten adapter case assembly mounting bolts to specified
torque.
CAUTION:
Do not reuse self-sealing bolt.
35. Install needle bearing in drum support edge surface.
CAUTION:
Apply petroleum jelly to needle bearing.
SCIA5231E
SCIA5205E
Adapter case assembly mounting bolt:
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt:
: 61 N·m (6.2 kg-m, 45 ft-lb)
SCIA5203E
SCIA5198E

AT-322
ASSEMBLY
Revision: August 20072004 QX56
53. Adjust brake band.
a. Loosen lock nut.
b. Tighten band servo anchor end pin to specified torque.
c. Back of band servo anchor end pin three turns.
d. Holding band servo anchor end pin, tighten lock nut to specified
torque. Refer to AT-261, "
Components" .
AdjustmentUCS002JR
TOTAL END PLAY

Measure clearance between front sun gear and bearing race for
oil pump cover.

Select proper thickness of bearing race so that end play is within
specifications.
1. Measure dimensions “K” and “L” and then calculate dimension
“J”.
a. Measure dimension “K”.: 5.0 N·m (0.51 kg-m, 44 in-lb)
SCIA2809E
SCIA2810E
SCIA5350E
SCIA5351E

ASSEMBLY
AT-325
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
3. Install oil pump assembly in transmission case.
CAUTION:
Apply ATF to oil pump radial bearing.
4. Apply recommended sealant (Genuine RTV Silicone Sealant or
equivalent. Refer to GI-45, "
Recommended Chemical Products
and Sealants" .) to oil pump assembly as shown in illustration.
CAUTION:
Complete remove all moisture, oil and old sealant, etc.
From the oil pump mounting bolts and oil pump mounting
bolt mounting surfaces.
5. Tighten oil pump mounting bolts to specified torque. Refer to AT-
261, "Components" .
CAUTION:
Apply ATF to oil pump bushing.
6. Install O-ring to input clutch assembly.
CAUTION:

Do not reuse O-ring.

Apply ATF to O-ring.
7. Install converter housing to transmission case.
CAUTION:
Do not reuse self-sealing bolt.
SCIA2 811 E
SCIA5321E
SCIA2300E
SCIA5 011 E
Converter housing mounting bolt:
: 52 N·m (5.3 kg-m, 38 ft-lb)
Self-sealing bolt:
: 61 N·m (6.2 kg-m, 45 ft-lb)
SCIA5171E

AT-326
ASSEMBLY
Revision: August 20072004 QX56
8. Make sure that brake band does not close turbine revolution
sensor hole.
9. Install control valve with TCM.
a. Install A/T fluid temperature sensor 2 to bracket.
b. Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM. Tighten A/T fluid temperature sensor 2 mount-
ing bolt to the specified torque. Refer to AT-261, "
Components"
.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
c. Install O-ring to A/T assembly harness connector.
CAUTION:

Do not reuse O-ring.

Apply ATF to O-ring.
d. Install control valve with TCM in transmission case.
CAUTION:

Make sure that turbine revolution sensor securely installs
turbine revolution sensor hole.

Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.

Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.
SCIA5034E
SCIA5264E
SCIA5301E
SCIA5155E
SCIA5034E

ASSEMBLY
AT-327
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56

Assemble it so that manual valve cutout is engaged with
manual plate projection.
e. Install bolts A, B and C to control valve with TCM.
f. Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After
that tighten them in order (1 → 2 → 3), and then tighten other
bolts.
g. Tighten control valve with TCM mounting bolts to the specified
torque. Refer to AT-261, "
Components" .
10. Connect A/T fluid temperature sensor 2 connector.
11. Securely fasten A/T fluid temperature sensor 2 harness with ter-
minal clip.
SCIA5035E
Bolt symbol Length: mm (in) Number of bolts
A 42 (1.65) 5
B 55 (2.17) 6
C 40 (1.57) 1
SCIA5025E
SCIA5037E
SCIA5023E
SCIA5146E

ASSEMBLY
AT-329
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
17. Install oil pan to transmission case.
a. Install oil pan gasket to oil pan.
CAUTION:

Do not reuse oil pan gasket.

Install it in the direction to align hole positions.

Complete remove all moisture, oil and old gasket, etc. From the oil pan gasket mounting sur-
faces.
b. Install oil pan (with oil pan gasket) to transmission case.
CAUTION:

Install it so that drain plug comes to the position as
shown in the figure.

Be careful not to pinch harnesses.

Complete remove all moisture, oil and old gasket, etc.
From the oil pan mounting surfaces.
c. Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Refer to AT- 2 6 1 , "
Components" .
CAUTION:
Do not reuse oil pan mounting bolts.
18. Install drain plug to oil pan. Tighten drain plug to the specified
torque. Refer to AT-261, "
Components" .
CAUTION:
Do not reuse drain plug gasket.
19. Install torque converter.
a. Pour ATF into torque converter.

Approximately 2 liter (2-1/8 US qt, 1-3/4 Imp qt) of fluid is
required for a new torque converter.

When reusing old torque converter, add the same amount
of fluid as was drained.
b. Install torque converter while aligning notches of torque con-
verter with notches of oil pump.
CAUTION:
Install torque converter while rotating it.
SCIA2308E
SCIA4 113 E
SAT4 2 8DA
SCIA5010E

AT-330
ASSEMBLY
Revision: August 20072004 QX56
c. Measure distance “A” to check that torque converter is in proper
position.
Distance “A”:
: 24.0 mm (0.94 in) or more
SAT0 1 7B

SERVICE DATA AND SPECIFICATIONS (SDS)
AT-331
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: August 20072004 QX56
SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
General SpecificationsUCS002J T
*1: Refer to MA-10, "Fluids and Lubricants" .
Vehicle Speed When Shifting GearsUCS002JU
NORMAL MODE

At half throttle, the accelerator opening is 4/8 of the full opening.
TOW MODE

At half throttle, the accelerator opening is 4/8 of the full opening. Applied model 4x2 4x4
Automatic transmission model RE5R05A
Transmission model code number 95X13 95X14
Stall torque ratio2.0: 1
Transmission gear ratio1st 3.827
2nd 2.368
3rd 1.519
4th 1.000
5th 0.834
Reverse 2.613
Recommended fluid NISSAN Matic Fluid J*1
Fluid capacity 10.6 liter (11-1/4 US qt, 9-3/8 Imp qt)
CAUTION:

Use only Genuine NISSAN ATF Matic Fluid J. Do not mix with other fluid.

Using automatic transmission fluid other than Genuine NISSAN an ATF Matic Fluid J will deteriorate in driveability and
automatic transmission durability, and may damage the automatic transmission, which is not covered by the warranty.
Final
gear
ratioThrottle positionVehicle speed km/h (MPH)
D
1 →D2D2 →D3D3 →D4D4 →D5D5 →D4D4 →D3D3 →D2D2 →D1
2.937Full throttle 70 - 74
(44 - 46)112 - 120
(70 - 75)176 - 186
(110 - 116)249 - 259
(155 - 161)245 - 255
(152 - 159)166 - 176
(103 - 110)100 - 108
(62 - 67)43 - 47
(27 - 30)
Half throttle 46 - 50
(28 - 31)74 - 82
(46 - 51)103 - 113
(64 - 70)135 - 145
(84 - 90)109 - 119
(68 - 74)69 - 79
(43 - 49)44 - 52
(27 - 32)11 - 1 5
(7 - 10)
3.357Full throttle 61 - 65
(38 - 41)97 - 105
(61 - 66)153 - 163
(95 - 102)236 - 246
(147 - 153)232 - 242
(144 - 151)143 - 153
(89 - 95)87 - 95
(54 - 59)43 - 47
(27 - 29)
Half throttle 41 - 45
(26 - 28)66 - 74
(41 - 46)89 - 99
(56 - 62)117 - 127
(73 - 79)95 - 105
(59 - 65)59 - 69
(37 - 43)38 - 46
(24 - 29)11 - 1 5
(7 - 10)
Final
gear
ratioThrottle positionVehicle speed km/h (MPH)
D
1 →D2D2 →D3D3 →D4D4 →D5D5 →D4D4 →D3D3 →D2D2 →D1
2.937Full throttle 70 - 74
(44 - 46)112 - 120
(70 - 75)176 - 186
(110 - 116)249 - 259
(155 - 161)245 - 255
(152 - 159)166 - 176
(103 - 110)100 - 108
(62 - 67)43 - 47
(27 - 30)
Half throttle 50 - 54
(31 - 34)81 - 89
(50 - 55)113 - 123
(70 - 76)135 - 145
(84 - 90)109 - 119
(68 - 74)68 - 78
(42 - 48)44 - 52
(27 - 32)11 - 1 5
(7 - 10)
3.357Full throttle 61 - 65
(38 - 41)97 - 105
(61 - 66)153 - 163
(95 - 102)236 - 246
(147 - 153)232 - 242
(144 - 151)143 - 153
(89 - 95)87 - 95
(54 - 59)43 - 47
(27 - 29)
Half throttle 43 - 47
(27 - 29)72 - 80
(45 - 50)98 - 108
(61 - 67)117 - 127
(73 - 79)95 - 105
(59 - 65)59 - 69
(37 - 43)37 - 45
(23 - 28)11 - 1 5
(7 - 10)