2004 INFINITI QX56 Air

BL-128
AUTOMATIC BACK DOOR SYSTEM
Revision: August 20072004 QX56
Cinch Latch Motor System InspectionEIS002TC
1. CINCH LATCH MOTOR CIRCUIT INSPECTION
1. Turn ignition switch OFF.
2. Disconnect back door latch and back door control unit.
3. Check continuity between back door control unit connector (A)
B55 terminals 11, 12 and back door latch (cinch latch motor)
connector (B) D503 terminals 1, 2.
4. Check continuity between back door latch (cinch latch motor)
connector (B) D503 terminals 1, 2 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace harness.
2. CINCH LATCH MOTOR OPERATION INSPECTION
Connect battery power to terminals 1 and 2 on the back door latch
and check motor operation.
OK or NG
OK >> GO TO 3.
NG >> Replace the back door latch.
3. CINCH LATCH MOTOR SIGNAL INSPECTION
1. Reconnect back door latch and back door control unit.
2. While fully opening and closing the back door, check voltage
between back door control unit connector B55 terminals 11, 12
and ground.
OK or NG
OK >> Cinch latch motor circuit is OK.
NG >> Replace the back door control unit.1 (L) - 12 (L) : Continuity should exist.
2 (Y) - 11 (Y) : Continuity should exist.
1 (L) - ground : Continuity should not exist.
2 (Y) - ground : Continuity should not exist.
LIIA2263E
1 (+) - 2 (-) : It operates.
1 (-) - 2 (+) : It operates. (Reverse rotation)
LIIA1937E
11 (Y) - Ground
12 (L) - Ground
LIIA0836ESIIA1480E

IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-149
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: August 20072004 QX56
4. CHECK GROUND CIRCUIT FOR BCM
1. Turn ignition switch OFF.
2. Check continuity between BCM connector M18 terminal 67 and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair or replace harness. Ref. part No. C3
5. REPLACE BCM
1. Replace BCM. Ref. part No. A
2. Perform initialization with CONSULT-II.
For initialization, refer to “CONSULT-II Operation Manual NATS-IVIS/NVIS”.
Does the engine start?
Yes >> BCM is malfunctioning.
No >> ECM is malfunctioning.

Replace ECM. Ref. part No. B

Perform initialization or re-communicating function.

For initialization, refer to “CONSULT-II Operation Manual NATS-IVIS/NVIS”.

For re-communicating function, refer to BL-140, "ECM Re-communicating Function" .
Diagnostic Procedure 2EIS002TV
Self-diagnostic results:
“DIFFERENCE OF KEY” displayed on CONSULT-II screen
1. CONFIRM SELF-DIAGNOSTIC RESULTS
Confirm SELF-DIAGNOSTIC RESULTS “DIFFERENCE OF KEY”
displayed on CONSULT-II screen.
Is CONSULT-II screen displayed as above?
Yes >> GO TO 2.
No >> GO TO BL-146, "
SYMPTOM MATRIX CHART 1" . 67 (B) - Ground : Continuity should exist.
LIIA1040E
PIIA1261E

IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-153
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: August 20072004 QX56
4. CHECK POWER SUPPLY FOR NATS ANTENNA AMP.
1. Turn ignition switch ON.
2. Check voltage between NATS antenna amp. connector M21 terminal 1 and ground.
OK or NG
OK >> GO TO 5.
NG >> Repair or replace fuse or harness. Ref. part No. E3
5. CHECK NATS ANTENNA AMP. SIGNAL LINE- 1
Check voltage between NATS antenna amp. connector M21 terminal
2 and ground with analog tester.
OK or NG
OK >> GO TO 6.
NG >>

Repair or replace harness. Ref. part No. E1
NOTE:
If harness is OK, replace BCM, refer to BCS-19, "
Removal and Installation of BCM" . Perform
initialization with CONSULT-II. For initialization, refer to “CONSULT-II Operation Manual NATS-
IVIS/NVIS”. 1 (W) - Ground : Battery voltage
LIIA1498E
LIIA1642E
Connector terminals
(wire colors)
Position of ignition key cylinderVoltage (V)
(Approx.)
( + ) ( - )
2 (G) GroundBefore inserting ignition key Battery voltage
After inserting ignition keyPointer of tester should move for approx. 30 seconds,
then return to battery voltage
Just after turning ignition
switch ONPointer of tester should move for approx. 1 second,
then return to battery voltage

BL-154
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
Revision: August 20072004 QX56
6. CHECK NATS ANTENNA AMP. SIGNAL LINE- 2
Check voltage between NATS antenna amp. connector M21 terminal
4 and ground with analog tester.
OK or NG
OK >> GO TO 7.
NG >>

Repair or replace harness. Ref. part No. E2
NOTE:
If harness is OK, replace BCM, refer to BCS-19, "
Removal and Installation of BCM" . Perform
initialization with CONSULT-II. For initialization, refer to “CONSULT-II Operation Manual NATS-
IVIS/NVIS”.
7. CHECK NATS ANTENNA AMP. GROUND LINE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect NATS antenna amp.
3. Check continuity between NATS antenna amp. connector M21 terminal 3 and ground.
OK or NG
OK >> NATS antenna amp. is malfunctioning. Ref. part No. E6
NG >>

Repair or replace harness.
NOTE:
If harness is OK, replace BCM, perform initialization
with CONSULT-II. For initialization, refer to “CON-
SULT-II Operation Manual NATS-IVIS/NVIS”.
LIIA1643E
Connector terminals
(wire colors)
Position of ignition key cylinderVoltage (V)
(Approx.)
( + ) ( - )
4 (BR) GroundBefore inserting ignition key Battery voltage
After inserting ignition keyPointer of tester should move for approx. 30 seconds,
then return to battery voltage
Just after turning ignition
switch ONPointer of tester should move for approx. 1 second,
then return to battery voltage
3 (B) - Ground : Continuity should exist.
LIIA1283E

IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-155
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: August 20072004 QX56
Diagnostic Procedure 6EIS002TZ
“SECURITY INDICATOR LAMP DOES NOT LIGHT UP”
1. CHECK FUSE
Check 10A fuse [No.19, located in the fuse block (J/B)]
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse.
2. CHECK SECURITY INDICATOR LAMP
1. Start engine and turn ignition switch OFF.
2. Check the security indicator lamp lights up.
OK or NG
OK >> Inspection End.
NG >> GO TO 3.
3. CHECK SECURITY INDICATOR LAMP POWER SUPPLY CIRCUIT
1. Disconnect security indicator lamp.
2. Check voltage between security indicator lamp connector M24
terminal 8 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK BCM (NATS CONTROL UNIT) FUNCTION
1. Connect security indicator lamp.
2. Disconnect BCM.
3. Check voltage between BCM connector M18 terminal 23 and
ground.
OK or NG
OK >> BCM is malfunctioning.

Replace BCM.
Ref. part No. A

Perform initialization with CONSULT-II.

For initialization, refer to “CONSULT-II Operation
Manual NATS-IVIS/NVIS”.
NG >> Check the following:

Harness for open or short between security indicator lamp and BCM (NATS control unit).

Indicator lamp condition Security indicator lamp should light up.
8 (Y/R) - Ground : Battery voltage
LIIA1072E
23 (G/O) - Ground : Battery voltage
LIIA0523E

BL-158
HOMELINK UNIVERSAL TRANSCEIVER
Revision: August 20072004 QX56
Trouble DiagnosesEIS0 02 U2
DIAGNOSTIC PROCEDURE
SYMPTOM: Transmitter does not activate receiver.
Before conducting the procedure given below, make sure that system receiver (garage door opener, etc.)
operates with original, hand-held transmitter. If NG, receiver or hand-held transmitter is at fault, not vehicle
related.
1. ILLUMINATE CHECK

Turn ignition switch OFF.

Does amber light (LED) of transmitter illuminate when any but-
ton is pressed?
YES or NO
YES >> GO TO 2.
NO >> GO TO 3.
2. TRANSMITTER CHECK
Check transmitter with Tool. For details, refer to Technical Service Bulletin.
OK or NG
OK >> Receiver or hand-held transmitter malfunction, not vehicle related.
NG >> Replace transmitter.
3. POWER SUPPLY CHECK
1. Disconnect transmitter.
2. Check voltage between HomeLink® universal transceiver connector R106 terminal 1 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace fuse or harness.
4. GROUND CIRCUIT CHECK
Check continuity between HomeLink® universal transceiver connector R106 terminal 2 (B) and body ground.
OK or NG
OK >> Replace HomeLink® universal transceiver.
NG >> Repair or replace harness.
LIIA1466E
1 (Y/R) - Ground : Battery voltage
LIIA1467E
2 (B) - Ground : Continuity should exist.
LIIA2039E

BL-160
BODY REPAIR
Revision: August 20072004 QX56
BODY REPAIRPFP:60100
Body Exterior Paint ColorEIS0 02 U3
M: Metallic; 2S: 2-Coat Solid, 2P: 2-Coat Pearl; 3P: 3-Coat Pearl; t: New Cross Linking Clear Coat
LIIA1437E
ComponentColor code A14 B18 EY2 G10 J20 K11 K12 Q11
DescriptionOpus
RedCobalt
Blue KashmirLiquid
OnyxJadeSilver
GraphiteSilver
IndulgenceTuscan
Pearl
Clear coat t t t t t t t t
1Outside
mirrorBodyChromium
plateCr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P
Base Black KH3 KH3 KH3 KH3 KH3 KH3 KH3 KH3
2Radiator
grilleCenter
and
emblemChromium
plateCr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P
3 Bumpers Fascias Body color A14 B18 EY2 G10 J20 K11 K12 Q11
4 Valance Black KH3 KH3 KH3 KH3 KH3 KH3 KH3 KH3
5Running
BoardsBody Body color A14 B18 EY2 G10 J20 K11 K12 Q11
Step
padBlack KH3 KH3 KH3 KH3 KH3 KH3 KH3 KH3
6Outside
handlesChromium
plateCr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P
7Side
Guard
MoldingBase Body color A14 B18 EY2 G10 J20 K11 BK12 BQ10
Top
TrimChromium
plateCr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P
8License
plate fin-
isherBase Body color A14 B18 EY2 G10 J20 K11 K12 Q11
Top and
bottom
trimChromium
plateCr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P Cr2P
9Cowl top
coverBody color A14 B18 EY2 G10 J20 K11 K12 Q11
10Rear
spoilerBody color A14 B18 EY2 G10 J20 K11 K12 Q11

BODY REPAIR
BL-161
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: August 20072004 QX56
Body Component PartsEIS002U4
UNDERBODY COMPONENT PARTS
LIIA0908E