2004 INFINITI QX56 ignition

DI-60
REAR SONAR SYSTEM
Revision: August 20072004 QX56
System DescriptionEKS007ET
FUNCTION
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 12 , located in the fuse block (J/B)]

to sonar control unit terminal 8, and

through 10A fuse [No. 51, located in the IPDM E/R]

to back-up lamp relay terminals 1 and 3.
Ground is supplied

to sonar control unit terminal 6

through body grounds B7 and B19.
With the ignition switch in the ON or START position, and the transmission gear selector lever in the R posi-
tion, power is supplied

to sonar control unit terminal 5

from back-up lamp relay terminal 5.
With power and ground supplied, transmission gear selector lever in R position, and the rear sonar system
OFF switch ON, the rear sonar system will detect obstacles within 1.8 m (5.9 ft.) of the rear sonar sensors.
The vehicle operator is notified of obstacles by varied rate of tone from the sonar buzzer depending on dis-
tance of obstacle being sensed.
REAR SONAR SYSTEM OFF SWITCH
With power and ground supplied to the sonar control unit, transmission gear selector lever in R position, the
sonar system can be disabled and the sonar buzzer silenced by momentarily pressing the rear sonar system
OFF switch. The rear sonar system OFF indicator lamp will be illuminated in the rear sonar system OFF
switch.
To disable the rear sonar system, ground is supplied

to sonar control unit terminal 13

through rear sonar system OFF switch terminal 1

through rear sonar system OFF switch terminal 2

from body grounds M57, M61, and M79.
To light the rear sonar system OFF indicator, power is supplied

to the rear sonar system OFF switch terminal 5

from sonar control unit terminal 4.
Ground is supplied

to the rear sonar system OFF switch terminal 6

from body grounds M57, M61, and M79.
The rear sonar system and buzzer will be disabled and the rear sonar system OFF indicator will be illuminated
until the ignition switch is turned OFF. When the ignition switch is turned ON, the rear sonar system will be
enabled. Depressing the rear sonar system OFF switch momentarily will enable the rear sonar system also.
Enabling the rear sonar system will cause the rear sonar system OFF indicator to go out.
SONAR BUZZER
With power supplied to the sonar control unit and the transmission gear selector lever in R position, a station-
ary object that is at least 7.0 cm (2.8 in.) wide and 1.0 m (39.0 in.) tall and that is closer than 1.8 meters (5.9 ft.)
will be detected by the rear sonar sensors, causing the sonar buzzer to sound a tone. As the vehicle moves
closer to the object, the rate of the tone will increase. When the object is less than 25.0 cm (10 in.) from the
rear bumper, the tone will sound continuously.
Power is supplied

to sonar buzzer terminal +

from sonar control unit terminal 7.
Ground is supplied

to sonar buzzer terminal -

from sonar control unit terminal 3.

DI-64
REAR SONAR SYSTEM
Revision: August 20072004 QX56
Terminals And Reference Value For Sonar Control UnitEKS007EV
How to Proceed With Trouble DiagnosisEKS007EW
1. Confirm the symptom or customer complaint.
2. Understand operation description and function description. Refer to DI-60, "
System Description" .
3. Perform pre-diagnosis inspection. Refer to DI-65, "
Pre-diagnosis Inspection" .
4. Perform self-diagnosis. Refer to DI-65, "
Self-diagnosis Function" .
5. Perform the preliminary check. Refer to DI-67, "
Preliminary Check" .
6. Check symptom and repair or replace the cause of malfunction. Refer to DI-68, "
Symptom Chart" .
7. Does the rear sonar system operate properly? If so, go to 8. If not, go to 3.
8. Clear fault codes. Refer to DI-66, "
IDLING OR CLEARING FAULT CODES MODE" .
9. Inspection End.
TERMINAL
(COLOR)ITEMCONDITION
Reference value (V)
(Approx.) IGNITION
SWITCHOPERATION
3 (R) Sonar buzzer return ON — 0 - 12 (variable)
4 (BR/Y)Rear sonar system
OFF indicator outputONRear sonar system OFF
switch ON 0
OFF 12
5 (G/W) Reverse signal ONTransmission gear
selector leverR position 12
Transmission gear
selector leverNot R position 0
6 (B)Sonar control unit
ground —— 0
7 (L) Sonar buzzer drive
signalON — 12
8 (G/R)Sonar control unit
powerON — 12
9 (GR)Rear sonar sensor
signal - RH outerON

Rear sonar system OFF switch ON

Transmission gear selector lever in R
position

No obstacles12
10 (P)Rear sonar sensor
signal - LH outerON

Rear sonar system OFF switch ON

Transmission gear selector lever in R
position

No obstacles12
11 ( O )Rear sonar sensor
signal - LH innerON

Rear sonar system OFF switch ON

Transmission gear selector lever in R
position

Distance obstacles12
12 (LG)Rear sonar sensor
signal - RH innerON

Rear sonar system OFF switch ON

Transmission gear selector lever in R
position

Distance obstacles12
13 (LG)Rear sonar system
OFF switch signalONRear sonar system OFF
switchON 0
OFF 12
15 (Y)Rear sonar sensor
groundON — 0
16 (LG/B)Rear sonar sensor
powerON Ignition switch ON 12

REAR SONAR SYSTEM
DI-65
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
Pre-diagnosis InspectionEKS007EX
SENSOR STATUS CHECK

Check that the rear sonar sensor is properly aligned (bumper is not misaligned, no deformation in sensor
mounting area.

Check that snow, mud, or other foreign objects are not adhering to the rear sonar sensor.

Check that there is no deformation, scratches, or other damage to the rear sonar sensor.

Check that water has not accumulated in the rear sonar sensor.
CAUTION:
Use water, cotton swab, or other soft material for cleaning the sensor.
1. Check that there are no obstacles within each rear sonar sensor's detection range.
2. Check that there are no nearby ultrasound sources (such as the sounds of vehicle horns, motorcycle
engines, or truck air brakes).
3. Check that the vehicle is on a level surface.
Self-diagnosis FunctionEKS007EY
There are four modes of self-diagnosis; entering diagnostics, requesting number of fault codes, requesting
fault codes, and idling or clearing fault codes. These steps must be followed in order. Self-diagnosis can be
manually exited by turning the ignition switch OFF, or selecting reverse gear. Self-diagnosis will exit unless a
fault code request occurs before a message is repeated five times without acknowledgement.
ENTERING DIAGNOSTICS MODE
1. Turn ignition switch ON. Rear sonar system OFF switch indica-
tor lamp illuminates for three seconds and then turns off.
2. Immediately push rear sonar system OFF switch ten times
within five seconds.
3. The sonar buzzer will sound once and the rear sonar system
OFF indicator will flash once.
REQUESTING NUMBER OF FAULT CODES MODE
1. While in diagnostic mode, push rear sonar system OFF switch
once.
2. The sonar buzzer will sound once.
3. Rear sonar system OFF indicator will flash once and sonar
buzzer will sound once for each fault code detected.
4. There will be a four second pause.
5. The number of fault codes will repeat five times then pause.
NOTE:
Self-diagnosis will exit unless requesting fault codes occurs
before five repeats ends.
Detection range
Rear sonar sensors Approx. 1.8 m (5.9 ft.) maximum
LKIA0389E
LKIA0388E

REAR SONAR SYSTEM
DI-67
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
Preliminary CheckEKS007EZ
INSPECTION FOR POWER SUPPLY AND GROUND CIRCUIT
1. CHECK FUSES

Check for blown rear sonar system fuses.
Refer to DI-62, "
Wiring Diagram — SONAR —" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of problem before installing new fuse. Refer to PG-4,
"POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Disconnect sonar control unit connector.
2. Check voltage between sonar control unit connector B56 termi-
nal 8 (G/R) and ground.
OK or NG
OK >> GO TO 3.
NG >> Check harness for open between sonar control unit and fuse.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between sonar control unit B56 terminal 6 and
ground.
OK or NG
OK >> Inspection End.
NG >> Check harness ground circuit.
Unit Power Source Fuse
Sonar control unit ON or START 12
Terminals Ignition switch position
(+)
(-) ON or START
ConnectorTe r m i n a l
(Wire color)
B56 8 (G/R) Ground Battery voltage
WKIA1145E
Te r m i n a l s
Continuity (+)
(–)
ConnectorTe r m i n a l
(Wire color)
B56 6 (B) Ground Yes
WKIA1146E

DI-72
REAR VIEW MONITOR
Revision: August 20072004 QX56
REAR VIEW MONITORPFP:28260
System DescriptionEKS007R4

When the A/T selector is in the reverse position, the display shows view to the rear of the vehicle.

Lines which indicate the vehicle clearance and distances are displayed on the monitor.
POWER SUPPLY AND GROUND
Power is supplied at all times

through 20A fuse [No. 31, located in the fuse and fusible link box]

to rear view camera control unit terminal 1.
When ignition switch is in ACC or ON position, power is supplied

through 10A fuse [No. 4, located in the fuse block (J/B)]

to rear view camera control unit terminal 2.
Ground is supplied

to rear view camera control unit terminal 3 and

to rear view camera terminal 2

through grounds B7 and B19.
AV COMMUNICATION LINE
Rear view camera control unit is connected to the following units with AV communication line. Each unit trans-
mits/receives data with AV communication line.

NAVI control unit

Display unit

Display control unit

AV switch
REAR VIEW CAMERA OPERATION
When ignition switch is in ON or START position, power is supplied

through 10A fuse (No. 51, located in the IPDM E/R)

to back-up lamp relay terminals 1 and 3.
When A/T selector lever is in reverse position, power is supplied

through back-up lamp relay terminal 2

to TCM terminal 7.
Then, when back-up lamp relay is energized,

from back-up lamp relay terminal 5

to rear view camera control unit terminal 4.
Then, rear view camera control unit is sent camera ON signal

through rear view camera control unit terminal 8

to rear view camera terminal 1.
An image taken by rear view camera is sent

through rear view camera terminals 3 and 4

to rear view camera control unit terminals 10 and 9.
Then an image is sent

through rear view camera control unit terminals 11 and 12

to the display unit terminals 4 and 15.
An image of rear view will be projected on the display.
Side Distance Guideline
When A/T selector lever is in reverse position, rear view camera control unit is sent rear view camera guideline
image

through rear view camera control unit terminals 11 and 12

to the display unit terminals 4 and 15.

DI-78
REAR VIEW MONITOR
Revision: August 20072004 QX56
Terminals and Reference Value for Rear View Camera Control UnitEKS007R8
Te r m i n a l
No.Wire
colorItemCondition
Reference value (V)
(Approx.) Ignition
switchOperation
1 Y Battery power OFF — Battery voltage
2 V ACC power ACC — Battery voltage
3 B Ground ON — 0
4 G/W Reverse signal input ONA/T selector lever R position Battery voltage
A/T selector lever in other than R
position0
5 BR AV Control ONA/T selector lever R position 0
—0
6G/WDDL — — —
8 Y Camera power output ON A/T selector lever R position 6
9 — Camera image input (–) ON — 0
10 G Camera image input (+) ON A/T selector lever R position
11 — Shield ground — — —
12 W Composite image output ON A/T selector lever R position
SKIA4894E
SKIA4896E

REAR VIEW MONITOR
DI-79
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
CONSULT-II Function (REARVIEW CAMERA)EKS007R9
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II BASIC OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1. With the ignition switch OFF, connect “CONSULT-II” and “CON-
SULT-II CONVERTER” to the data link connector, then turn igni-
tion switch ON.
2. Touch “START (NISSAN BASED VHCL)”.
3. Touch “REARVIEW CAMERA” on “SELECT SYSTEM” screen. If
“REARVIEW CAMERA” is not indicated, go to GI-39, "
CON-
SULT-II Data Link Connector (DLC) Circuit" .
REARVIEW CAMERA
diagnostic modeDescription
WORK SUPPORTSupports inspection and adjustments. Commands are transmitted to the rearview camera control unit
for setting the status suitable for required operation, input/output signals are received from the rear-
view camera control unit and received data is displayed.
DATA MONITOR Displays rearview camera control unit input/output data in real time.
ECU PART NUMBER Rearview camera control unit part number can be read.
BBIA0369E
BCIA0029E
BCIA0030E

REAR VIEW MONITOR
DI-81
C
D
E
F
G
H
I
J
L
MA
B
DI
Revision: August 20072004 QX56
Side Distance Guideline CorrectionEKS007RA
This mode is used to modify the side distance guidelines if they are dislocated from the rear view monitor
image, because of variations of body/camera mounting conditions.
SIDE DISTANCE GUIDELINE CORRECTION PROCEDURE
1. Create a correction line to modify the screen.
Draw lines on the rearward of the vehicle passing through the
following points: 200 mm (7.87 inch) from both sides of the vehi-
cle, and

*1: 0.5 m (1.5 feet)

*2: 1 m (3 feet)

*3: 2 m (7 feet)

*4: 3 m (10 feet)
and from the rear end of the bumper
2. With the ignition switch OFF, connect “CONSULT-II” and “CON-
SULT-II CONVERTER” to the data link connector, then turn igni-
tion switch ON. Touch “REARVIEW CAMERA” on “SELECT
SYSTEM” screen.
CAUTION:
Stop engine for safety when correcting side distance guide-
line.
3. Shift the A/T select lever to R position.
4. Touch “SELCT GUIDELINE PATTERN” on “SELECT WORK
ITEM” screen.
SKIA5637E
SKIA6103E
SKIA5638E