2004 INFINITI QX56 headlamp
[x] Cancel search: headlampPage 1854 of 3371
FRONT BUMPER
EI-13
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: August 20072004 QX56
FRONT BUMPERPFP:F2022
Removal and InstallationEIS002X7
REMOVAL
1. Remove side screws from fascia assembly.
2. Remove screws from front of fender protector. Refer to EI-23, "
FENDER PROTECTOR" .
1. Lower energy absorber 2. Front bumper side bracket RH 3. Front bumper stay RH
4. Upper bumper reinforcement 5. Plastic clip 6. Upper energy absorber (part of
upper bumper reinforcement)
7. Fastener 8. Front fascia assembly 9. Front fascia bracket
10. Front undercover 11. Fog/turn lamp 12. Fog/turn lamp LH/RH finisher
13. Spring nut 14. Front bumper stay LH 15. Front bumper side bracket LH
16. Plastic clip 16. Headlamp finisher (RH shown)
WIIA0260E
Page 1861 of 3371
EI-20
FRONT FENDER
Revision: August 20072004 QX56
FRONT FENDERPFP:63100
Removal and InstallationEIS002XB
1. Remove headlamp. Refer to LT- 3 3 , "Removal and Installation" .
2. Remove over fender. Refer to EI-21, "
OVER FENDER" .
3. Remove fender protector. Refer to EI-23, "
FENDER PROTECTOR" .
4. Remove hood stay. Refer to BL-12, "
HOOD" .
5. Remove front fender.
Installation is in the reverse order of removal.
WIIA0263E
Page 2242 of 3371
IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
H
H/AIM - Wiring diagram ...................................... LT-66
H/LAMP - Wiring diagram .................................. LT-10
Handling precautions for plastics ..................... BL-189
Harness connector ............................................ PG-68
Harness layout .................................................. PG-40
Hazard warning lamp ......................................... LT-80
Headlamp ............................................................. LT-6
Headlamp aiming control ................................... LT-65
Headlamp leveler - See Headlamp aiming control . LT-
65
Headlamp removal and installation .................... LT-33
Heated oxygen sensor 2 (bank 1) .... EC-186, EC-196,
EC-383
, EC-395
Heated oxygen sensor 2 (bank 2) .... EC-186, EC-196,
EC-383
, EC-395
Heated oxygen sensor 2 heater (bank 1) ........ EC-138
Heated oxygen sensor 2 heater (bank 2) ........ EC-138
Heated seat ....................................................... SE-89
Heater and cooling unit (Heater core) . ATC-144, ATC-
147
Heater unit (heater core) ............... ATC-144, ATC-147
Height (Dimensions) ........................................... GI-49
HFC134a (R134a) system identification ........... ATC-7
HFC134a (R134a) system precaution ............... ATC-5
HFC134a (R134a) system service procedure ATC-162
HFC134a (R134a) system service tools ......... ATC-14
HFC134a system service equipment precaution ATC-
11
High and low reverse clutch solenoid valve .... AT-163,
AT-166
Horn ................................................................ WW-56
HORN - Wiring diagram .................................. WW-56
How to erase DTC for OBD system .................. EC-62
HSEAT - Wiring diagram ................................... SE-91
I
I/MIRR - Wiring diagram ................................... GW-76
IATS - Wiring diagram ..................................... EC-162
ICC - Wiring diagram ....................................... ACS-20
ICC/BS - Wiring diagram ................................. EC-527
ICC/SW - Wiring diagram ................................ EC-512
ICCBOF - Wiring diagram ............................... EC-614
Identification plate .............................................. GI-47
Idle air volume learning ..................................... EC-44
Idle mixture ratio ................................................ EC-33
Idle speed .......................................................... EC-33
Idle speed control (ISC) .................... EC-342, EC-344
Ignition coil .......................................... EM-26, EC-583
Ignition control system .................................... EC-583
Ignition key hole illumination ............................ LT-129
Ignition timing .................................................... EC-33
IGNSYS - Wiring diagram ............................... EC-584
ILL - Wiring diagram ......................................... LT-158
Illumination ....................................................... LT-152
Illumination control .............................. LT-152, LT-169
In vehicle sensor ........................... ATC-128, ATC-137
In-cabin Microfilter ............................................. MA-20
INJECT - Wiring diagram ................................. EC-596
Injector ............................................................. EC-595
Input clutch solenoid valve ................. AT-145, AT-148
Instrument panel .................................................. IP-10
Instrument panel speaker .................................. AV-46
INT/L - Wiring diagram ..................................... LT-135
Intake air temperature sensor ............ EC-161, EC-181
Intake door control linkage adjustment . ATC-78, ATC-
80
Intake door motor ........................... ATC-76, ATC-151
Intake manifold .................................................. EM-15
Intake sensor ................................ ATC-133, ATC-139
Intelligent cruise control (ICC) system ............... ACS-6
Interior ................................................................. EI-34
Interior lamp ...................................................... LT-129
Interior lamp on-off control ................................ LT-129
Internal gear (Transfer) ..................................... TF-127
IPDM (Intelligent power distribution module engine
room) ................................................................. PG-17
IVIS (Infiniti vehicle immobilizer system) precautions ...
GI-3
J
Jacking points ..................................................... GI-40
Junction box (J/B) .............................................. PG-76
K
Key illumination ................................................ LT-129
Keyless entry system - See Multi-remote control system
BL-44
Knock sensor (KS) ........................................... EC-250
KS - Wiring diagram ........................................ EC-251
L
Length (Dimensions) .......................................... GI-49
License lamp .................................................... LT-108
Lifting points ....................................................... GI-41
Line pressure solenoid valve ........................... AT-124
Line pressure switch (Transfer) .......................... TF-95
Line pressure test (A/T) ..................................... AT-59
Liquid gasket application ......................... LU-2, FFD-2
Location of electrical units ................................. PG-64
Low coast brake solenoid valve .......... AT-169, AT-172
Low tire pressure warning system ...................... WT-7
Low tire pressure warning system - trouble diagnoses
WT-10
Low tire pressure warning system - Wiring diagram .....
WT-10
Lubricant (R134a) A/C ..................................... ATC-22
Lubricants .......................................................... MA-10
Lubrication circuit (engine) .................................. LU-5
Lubrication oil A/C ........................................... ATC-22
Lubrication-locks, hinges and hood latches ....... MA-30
Page 2432 of 3371
LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION LT
A
B
LT
Revision: August 20072004 QX56 PRECAUTIONS .......................................................... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 4
General precautions for service operations ............. 5
Wiring Diagrams and Trouble Diagnosis .................. 5
HEADLAMP (FOR USA) ............................................ 6
Component Parts and Harness Connector Location ..... 6
System Description .................................................. 6
OUTLINE ............................................................... 6
XENON HEADLAMP ............................................. 7
BATTERY SAVER CONTROL .............................. 8
AUTO LIGHT OPERATION ................................... 8
VEHICLE SECURITY SYSTEM (PANIC ALARM) ..... 8
CAN Communication System Description ................ 8
Schematic ................................................................ 9
Wiring Diagram — H/LAMP — ............................... 10
Terminals and Reference Values for BCM ............. 14
Terminals and Reference Values for IPDM E/R ..... 15
How to Proceed With Trouble Diagnosis ................ 15
Preliminary Check .................................................. 16
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 16
CONSULT-II Function (BCM) ................................. 18
CONSULT-II OPERATION .................................. 18
WORK SUPPORT ............................................... 19
DATA MONITOR ................................................. 19
ACTIVE TEST ..................................................... 20
SELF-DIAGNOSTIC RESULTS .......................... 20
CONSULT-II Function (IPDM E/R) ......................... 21
CONSULT-II OPERATION .................................. 21
DATA MONITOR ................................................. 22
ACTIVE TEST ..................................................... 22
Headlamp HI Does Not Illuminate (Both Sides) ..... 23
Headlamp HI Does Not Illuminate (One Side) ....... 25
High Beam Indicator Lamp Does Not Illuminate .... 26
Headlamp LO Does Not Illuminate (Both Sides) .... 26
Headlamp LO Does Not Illuminate (One Side) ...... 28
Headlamps Do Not Turn OFF ................................ 29
Aiming Adjustment ................................................. 31LOW BEAM AND HIGH BEAM ........................... 31
Bulb Replacement .................................................. 32
HEADLAMP (OUTER SIDE), FOR LOW BEAM ... 32
HEADLAMP (INNER SIDE), FOR HIGH BEAM ... 32
FRONT PARKING LAMP (INNER OR OUTER) ... 32
FRONT SIDE MARKER LAMP ........................... 32
Removal and Installation ........................................ 33
REMOVAL ........................................................... 33
INSTALLATION ................................................... 33
Disassembly and Assembly .................................... 33
HEADLAMP (FOR CANADA) - DAYTIME LIGHT
SYSTEM - .................................................................. 34
Component Parts and Harness Connector Location ... 34
System Description ................................................. 35
OUTLINE ............................................................. 35
DAYTIME LIGHT OPERATION ........................... 35
COMBINATION SWITCH READING FUNCTION ... 35
AUTO LIGHT OPERATION ................................. 35
CAN Communication System Description .............. 35
Schematic ............................................................... 36
Wiring Diagram — DTRL — ................................... 37
Terminals and Reference Values for BCM .............. 41
How to Proceed With Trouble Diagnosis ................ 42
Preliminary Check .................................................. 42
CHECK BCM CONFIGURATION ........................ 42
INSPECTION FOR POWER SUPPLY AND
GROUND CIRCUIT ............................................. 42
INSPECTION PARKING BRAKE SWITCH CIR-
CUIT .................................................................... 43
CONSULT-II Functions ........................................... 44
Daytime Light Control Does Not Operate Properly
(Normal Headlamps Operate Properly) .................. 44
Aiming Adjustment .................................................. 46
Bulb Replacement .................................................. 46
Removal and Installation ........................................ 46
Disassembly and Assembly .................................... 46
AUTO LIGHT SYSTEM ............................................. 47
Component Parts and Harness Connector Location ... 47
System Description ................................................. 48
OUTLINE ............................................................. 48
Page 2433 of 3371
LT-2Revision: August 20072004 QX56 COMBINATION SWITCH READING FUNCTION ... 48
EXTERIOR LAMP BATTERY SAVER CONTROL ... 48
DELAY TIMER FUNCTION ................................. 48
CAN Communication System Description .............. 48
Major Components and Functions .......................... 48
Schematic ............................................................... 49
Wiring Diagram — AUTO/L — ................................ 50
Terminals and Reference Values for BCM .............. 53
Terminals and Reference Values for IPDM E/R ...... 54
How to Proceed With Trouble Diagnosis ................ 55
Preliminary Check .................................................. 55
SETTING CHANGE FUNCTIONS ....................... 55
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 55
CONSULT-II Function (BCM) .................................. 57
CONSULT-II OPERATION ................................... 57
WORK SUPPORT ............................................... 58
DATA MONITOR .................................................. 58
ACTIVE TEST ..................................................... 59
SELF-DIAGNOSTIC RESULTS ........................... 59
CONSULT-II Function (IPDM E/R) .......................... 60
CONSULT-II OPERATION ................................... 60
DATA MONITOR .................................................. 61
ACTIVE TEST ..................................................... 61
Trouble Diagnosis Chart by Symptom .................... 62
Lighting Switch Inspection ...................................... 62
Optical Sensor System Inspection .......................... 63
Removal and Installation of Optical Sensor ............ 64
REMOVAL ........................................................... 64
INSTALLATION .................................................... 64
HEADLAMP AIMING CONTROL .............................. 65
System Description ................................................. 65
Wiring Diagram — H/AIM — ................................... 66
Removal and Installation ........................................ 68
Switch Circuit Inspection ........................................ 68
FRONT FOG LAMP .................................................. 69
Component Parts and Harness Connector Location ... 69
System Description ................................................. 69
OUTLINE ............................................................. 69
COMBINATION SWITCH READING FUNCTION ... 70
EXTERIOR LAMP BATTERY SAVER CONTROL ... 70
CAN Communication System Description .............. 70
Wiring Diagram — F/FOG — .................................. 71
Terminals and Reference Values for BCM .............. 73
Terminals and Reference Values for IPDM E/R ...... 74
How to Proceed With Trouble Diagnosis ................ 74
Preliminary Check .................................................. 75
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .................................................................... 75
CONSULT-II Functions ........................................... 76
Front Fog Lamps Do Not Illuminate (Both Sides) ... 76
Front Fog Lamp Does Not Illuminate (One Side) ... 77
Aiming Adjustment .................................................. 78
Bulb Replacement .................................................. 79
Removal and Installation ........................................ 79
TURN SIGNAL AND HAZARD WARNING LAMPS ... 80
Component Parts and Harness Connector Location ... 80
System Description ................................................. 80
OUTLINE ............................................................. 80TURN SIGNAL OPERATION ...............................80
HAZARD LAMP OPERATION .............................81
REMOTE KEYLESS ENTRY SYSTEM OPERA-
TION ....................................................................82
COMBINATION SWITCH READING FUNCTION ...82
CAN Communication System Description ..............82
Wiring Diagram — TURN — ...................................83
Terminals and Reference Values for BCM ..............85
How to Proceed With Trouble Diagnosis ................86
Preliminary Check ...................................................87
CHECK POWER SUPPLY AND GROUND CIR-
CUIT .....................................................................87
CONSULT-II Function (BCM) ..................................88
CONSULT-II OPERATION ...................................88
DATA MONITOR ..................................................89
ACTIVE TEST ......................................................89
Turn Signal Lamp Does Not Operate ......................90
Rear Turn Signal Lamp Does Not Operate .............91
Hazard Warning Lamp Does Not Operate But Turn
Signal Lamps Operate ............................................92
Turn Signal Indicator Lamp Does Not Operate .......93
Bulb Replacement (Front Turn Signal Lamp) ..........94
Bulb Replacement (Rear Turn Signal Lamp) ..........94
Removal and Installation of Front Turn Signal Lamp ...94
Removal and Installation of Rear Turn Signal Lamp ...94
LIGHTING AND TURN SIGNAL SWITCH ................95
Removal and Installation .........................................95
REMOVAL ............................................................95
INSTALLATION ....................................................95
HAZARD SWITCH .....................................................96
Removal and Installation .........................................96
REMOVAL ............................................................96
INSTALLATION ....................................................96
COMBINATION SWITCH ..........................................97
Wiring Diagram — COMBSW — ............................97
Combination Switch Reading Function ...................98
CONSULT-II Function (BCM) ..................................98
CONSULT-II OPERATION ...................................98
DATA MONITOR ..................................................99
Combination Switch Inspection ............................. 100
Removal and Installation ....................................... 102
Switch Circuit Inspection ....................................... 102
STOP LAMP ............................................................ 103
System Description ............................................... 103
Wiring Diagram — STOP/L — .............................. 104
High-Mounted Stop Lamp ..................................... 105
BULB REPLACEMENT ...................................... 105
REMOVAL AND INSTALLATION ....................... 105
Stop Lamp ............................................................. 105
BULB REPLACEMENT ...................................... 105
REMOVAL AND INSTALLATION ....................... 105
BACK-UP LAMP ..................................................... 106
Wiring Diagram — BACK/L — .............................. 106
Bulb Replacement ................................................. 107
Removal and Installation ....................................... 107
PARKING, LICENSE PLATE AND TAIL LAMPS .... 108
Component Parts and Harness Connector Location . 108
System Description ............................................... 108
OPERATION BY LIGHTING SWITCH ............... 109
Page 2434 of 3371
LT-3
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: August 20072004 QX56 COMBINATION SWITCH READING FUNCTION . 109
EXTERIOR LAMP BATTERY SAVER CONTROL . 109
CAN Communication System Description ............ 109
Schematic ............................................................. 110
Wiring Diagram — TAIL/L — ................................ . 111
Terminals and Reference Values for BCM ............ 114
Terminals and Reference Values for IPDM E/R .... 115
How to Proceed With Trouble Diagnosis ............... 115
Preliminary Check ................................................. 116
CHECK POWER SUPPLY AND GROUND CIR-
CUIT ................................................................... 116
CONSULT-II Functions .......................................... 117
Parking, License Plate and/or Tail Lamps Do Not
Illuminate ............................................................... 117
Parking, License Plate and Tail Lamps Do Not Turn
OFF (After Approx. 10 Minutes) ........................... 120
Front Parking Lamp .............................................. 121
BULB REPLACEMENT ..................................... 121
Tail Lamp .............................................................. 121
BULB REPLACEMENT ..................................... 121
License Plate Lamp .............................................. 121
BULB REPLACEMENT ..................................... 121
REAR COMBINATION LAMP ................................ 122
Bulb Replacement (Turn Signal) .......................... 122
Removal and Installation ...................................... 122
.......................................................................... 122
TRAILER TOW ....................................................... 123
Component Parts and Harness Connector Location . 123
System Description .............................................. 123
TRAILER TAIL LAMP OPERATION .................. 124
TRAILER BRAKE, TURN SIGNAL AND HAZARD
LAMP OPERATION .......................................... 124
TRAILER BRAKE OPERATION ........................ 124
TRAILER POWER SUPPLY OPERATION ........ 124
Schematic ............................................................ 125
Wiring Diagram — T/TOW — ............................... 126
INTERIOR ROOM LAMP ........................................ 129
Component Parts and Harness Connector Location . 129
System Description .............................................. 130POWER SUPPLY AND GROUND ....................130
SWITCH OPERATION ......................................131
ROOM LAMP TIMER OPERATION ..................131
INTERIOR LAMP BATTERY SAVER CONTROL .132
Schematic .............................................................133
Wiring Diagram — INT/L — ..................................135
Terminals and Reference Values for BCM ............142
How to Proceed With Trouble Diagnosis ..............142
Preliminary Check ................................................143
INSPECTION FOR POWER SUPPLY AND
GROUND CIRCUIT ...........................................143
CONSULT-II Function (BCM) ...............................144
CONSULT-II OPERATION .................................144
WORK SUPPORT .............................................145
DATA MONITOR ...............................................145
ACTIVE TEST ...................................................146
Room/Map Lamp Control Does Not Operate .......146
Personal Lamp Control Does Not Operate (Room/
Map Lamps Operate) ............................................148
All Step/Foot/Puddle Lamps Do Not Operate .......149
All Interior Room Lamps Do Not Operate .............150
Ignition Keyhole Illumination Control Does Not
Operate .................................................................150
ILLUMINATION .......................................................152
Component Parts and Harness Connector Location .152
System Description ...............................................152
ILLUMINATION OPERATION BY LIGHTING
SWITCH ............................................................153
EXTERIOR LAMP BATTERY SAVER CONTROL .154
CAN Communication System Description ............154
Schematic .............................................................155
Wiring Diagram — ILL — ......................................158
Removal and Installation ......................................169
ILLUMINATION CONTROL SWITCH ................169
BULB SPECIFICATIONS ........................................170
Headlamp .............................................................170
Exterior Lamp .......................................................170
Interior Lamp/Illumination .....................................170
Page 2436 of 3371
PRECAUTIONS
LT-5
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: August 20072004 QX56
General precautions for service operationsEKS007RV
Never work with wet hands.
Xenon headlamp includes high voltage generating part. Be sure
to disconnect battery negative cable (negative terminal) or
power fuse before removing, installing, or touching the xenon
headlamp (including lamp bulb).
Turn the lighting switch OFF before disconnecting and connect-
ing the connector.
When turning the xenon headlamp on and while it is illuminated,
never touch the harness, bulb, and socket of the headlamp.
When checking the headlamp on/off operation, check it on vehi-
cle and with the power connected to the vehicle-side connector.
Do not touch the headlamp bulb glass surface with bare hands or allow oil or grease to get on it. Do not
touch the headlamp bulb just after the headlamp is turned off, because it is very hot.
Install the xenon headlamp bulb socket correctly. If it is installed
improperly, high-voltage leak or corona discharge may occur
that can melt the bulb, connector, and housing. Do not illuminate
the xenon headlamp bulb out of the headlamp housing. Doing
so can cause fire and harm your eyes.
When the bulb has burned out, wrap it in a thick vinyl bag and
discard. Do not break the bulb.
Leaving the bulb removed from the headlamp housing for a long
period of time can deteriorate the performance of the lens and
reflector (dirt, clouding). Always prepare a new bulb and have it
on hand when replacing the bulb.
Do not use organic solvent (paint thinner or gasoline) to clean
lamps and to remove old sealant.
Wiring Diagrams and Trouble DiagnosisEKS0079O
When you read wiring diagrams, refer to the following:
Refer to GI-15, "How to Read Wiring Diagrams" in GI section.
Refer to PG-4, "POWER SUPPLY ROUTING CIRCUIT" for power distribution in PG section.
When you perform trouble diagnosis, refer to the following:
Refer to GI-11, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES" in GI section.
Refer to GI-27, "How to Perform Efficient Diagnosis for an Electrical Incident" in GI section.
WKIA0460E
EL-3422D
Page 2437 of 3371
LT-6
HEADLAMP (FOR USA)
Revision: August 20072004 QX56
HEADLAMP (FOR USA)PFP:26010
Component Parts and Harness Connector LocationEKS0079P
System DescriptionEKS0079Q
Control of the headlamp system operation is dependent upon the position of the combination switch (lighting
switch). When the lighting switch is placed in the 2ND position, the BCM (body control module) receives input
requesting the headlamps (and tail lamps) illuminate. This input is communicated to the IPDM E/R (intelligent
power distribution module engine room) across the CAN communication lines. The CPU (central processing
unit) of the IPDM E/R controls the headlamp high and headlamp low relay coils. When energized, these relays
direct power to the respective headlamps, which then illuminate.
OUTLINE
Power is supplied at all times
to headlamp high relay, located in the IPDM E/R, and
to headlamp low relay, located in the IPDM E/R, and
to ignition relay, located in the IPDM E/R, and
through 20A fuse (No. 53, located in the IPDM E/R)
to CPU of the IPDM E/R, and
through 10A fuse [No. 19, located in the fuse block (J/B)]
WKIA3392E