2004 INFINITI FX35 pg power

TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC ITEMS
ACS-53
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
12. CHECK ICC BRAKE HOLD RELAY

Check continuity between ICC brake hold relay terminal 1 and
terminal 2.
OK or NG
OK >> GO TO 13.
NG >> Replace ICC brake hold relay. Erase DTC and perform
ICC system running test. Then perform self-diagnosis of
ICC system again.
13. CHECK ICC UNIT STANDARD VOLTAGE
With CONSULT-II
1. Connect connectors of ICC unit and stop lamp switch.
2. Active test (STOP LAMP: STP LMP DRIVE ON) with CONSULT-
II, check voltage between ICC unit harness connector M89 ter-
minal 47 (W/R) and ground.
OK or NG
OK >> GO TO 14.
NG >> Replace ICC unit. Erase DTC and perform ICC system
running test. Then perform self-diagnosis of ICC system
again.
14. CHECK ICC BRAKE HOLD RELAY POWER SUPPLY CIRCUIT
1. Check voltage between ICC brake hold relay harness connector
E14 terminal 6 (GY) and ground.
OK or NG
OK >> GO TO 15.
NG >>

Malfunctions of fuse or ICC brake hold relay power
supply harness.

After repair, erase DTC and perform ICC system run-
ning test. Then, perform self-diagnosis of ICC system
again. Continuity should exist.
SKIA6662E
47 - Ground Approx. 12V (during active
test)
SKIA3075E
6 - Ground Approx. 12V
SKIA1198E

TROUBLE DIAGNOSIS FOR SYMPTOMS
ACS-59
[ICC]
C
D
E
F
G
H
I
J
L
MA
B
ACS
Revision: 2004 November 2004 FX35/FX45
TROUBLE DIAGNOSIS FOR SYMPTOMSPFP:00007
Symptom ChartAKS006ZN
Symptoms Reference page
OperationON/OFF switch does not switch ON.Symptom 1
ACS-60
ON/OFF switch does not switch OFF.Symptom 1
ACS-60
Cruise does not function for setting (powering functions).Symptom 2
ACS-60
CANCEL switch does not function.Symptom 3
ACS-61
Resume does not function.Symptom 3
ACS-61
The set speed does not increase.Symptom 3
ACS-61
The set distance to the vehicle ahead cannot be changed.Symptom 3
ACS-61
The ICC is not cancelled when the gear is in other than D.Symptom 4
ACS-62
Display/ChimeThe ICC system display does not appear.Check combination meter.
Refer to DI-13, "
How to Pro-
ceed With Trouble Diagnosis"
Chime does not function.Symptom 5
ACS-62
Control Driving force is hunting.Symptom 6
ACS-63
Function to detect the vehicle
aheadThe system frequently cannot detect the vehicle ahead.Symptom 7
ACS-63
The distance to detect the vehicle ahead is short.Symptom 7
ACS-63
The system misidentifies a vehicle even though there is no
vehicle ahead.

Refer to ACS-12, "LASER
BEAM AIMING ADJUST-
MENT"

Refer to ACS-9, "ICC Sys-
tem Running Test"
The system misidentifies a vehicle in the next lane.

Refer to ACS-12, "LASER
BEAM AIMING ADJUST-
MENT"

Refer to ACS-9, "ICC Sys-
tem Running Test"
The system does not detect a vehicle at all.Symptom 8
ACS-63

ACS-60
[ICC]
TROUBLE DIAGNOSIS FOR SYMPTOMS
Revision: 2004 November 2004 FX35/FX45
Symptom 1: ON/OFF Switch Does Not Switch ON*1 . ON/OFF Switch Does Not
Switch OFF
*2 .AKS006ZO
NOTE:

*1:The ICC system display in the combination meter does not illuminate.

*2:The ICC system display in the combination meter remains powered.
1. CHECK ON/OFF SWITCH
With CONSULT-II

With data monitor, check that ON/OFF switch operates normally.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
2. CHECK CONNECTOR ICC UNIT
1. Turn ignition switch OFF.
2. Disconnect ICC unit connector.
3. Check connector housing for disconnected, loose, bent, and collapsed terminals.
OK or NG
OK >> GO TO 3.
NG >>

Poor connector connection.

Repair ICC unit connector. After repair, erase DTC and perform ICC system running test. Then
perform self-diagnosis of ICC system again.
3. DIAGNOSIS CHECK
With CONSULT-II

Perform self-diagnosis with CONSULT-II.Is“CAN COMM CIRCUIT”indicated?
YES or NO
YES >> Refer toACS-41, "DTC 20 CAN COMM CIRCUIT"
NO >> Refer toACS-45, "DTC 46 OPERATION SW CIRC"
Symptom 2: The ICC System Cannot Be Set (ON/OFF Switch Turns On/Off).AKS006ZP
The ICC cannot be set in the following cases.

When the vehicle speed is not in range of approx. 25 MPH (40 km/h) to 90 MPH (144 km/h).

When the A/T selector lever is in gears other than ‘D’.

While the brake is in operation.
1. CHECK OF CAUSE OF AUTOMATIC CANCELLATION
With CONSULT-II
1. With “CAUSE OF AUTO-CANCEL” in work support, check if any cause of cancellation exists.
OK or NG
OK >>
Cancel with appropriate cause.

For causes A, B, or C, go to specified diagnosis.
A:“OPE SW VOLT CIRC” : Refer to ACS-45, "
DTC 46 OPERATION SW CIRC" .
B:“ VHCL SPD UNMATCH” : Refer to ACS-42, "
DTC 41 VHCL SPEED SE CIRC" .
C:“IGN LOW VOLT” : Refer to ACS-42, "
DTC 31 POWER SUPPLY CIR, DTC 34
POWER SUPPLY CIR 2" .
NG >> GO TO 2.

AT-2Revision: 2004 November 2004 FX35/FX45Wiring Diagram — AT — PNP/SW .......................113
Diagnostic Procedure ...........................................114
DTC P0720 VEHICLE SPEED SENSOR A/T (REV-
OLUTION SENSOR) ...............................................116
Description ............................................................116
CONSULT-II Reference Value ..............................116
On Board Diagnosis Logic ....................................116
Possible Cause .....................................................116
DTC Confirmation Procedure ...............................116
Wiring Diagram — AT — VSSA/T .........................118
Diagnostic Procedure ...........................................119
DTC P0725 ENGINE SPEED SIGNAL ...................121
Description ............................................................121
CONSULT-II Reference Value ..............................121
On Board Diagnosis Logic ....................................121
Possible Cause .....................................................121
DTC Confirmation Procedure ...............................121
Diagnostic Procedure ...........................................121
DTC P0740 TORQUE CONVERTER CLUTCH
SOLENOID VALVE .................................................123
Description ............................................................123
CONSULT-II Reference Value ..............................123
On Board Diagnosis Logic ....................................123
Possible Cause .....................................................123
DTC Confirmation Procedure ...............................123
Diagnostic Procedure ...........................................124
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP) .125
Description ............................................................125
CONSULT-II Reference Value ..............................125
On Board Diagnosis Logic ....................................125
Possible Cause .....................................................125
DTC Confirmation Procedure ...............................125
Diagnostic Procedure ...........................................126
DTC P0745 LINE PRESSURE SOLENOID VALVE .127
Description ............................................................127
CONSULT-II Reference Value ..............................127
On Board Diagnosis Logic ....................................127
Possible Cause .....................................................127
DTC Confirmation Procedure ...............................127
Diagnostic Procedure ...........................................128
DTC P1701 TRANSMISSION CONTROL MODULE
(POWER SUPPLY) ..................................................129
Description ............................................................129
On Board Diagnosis Logic ....................................129
Possible Cause .....................................................129
DTC Confirmation Procedure ...............................129
Wiring Diagram — AT — POWER ........................130
Diagnostic Procedure ...........................................131
DTC P1702 TRANSMISSION CONTROL MODULE
(RAM) ......................................................................133
Description ............................................................133
On Board Diagnosis Logic ....................................133
Possible Cause .....................................................133
DTC Confirmation Procedure ...............................133
Diagnostic Procedure ...........................................133
DTC P1703 TRANSMISSION CONTROL MODULE
(ROM) ......................................................................134
Description ............................................................134
On Board Diagnosis Logic ....................................134Possible Cause .....................................................134
DTC Confirmation Procedure ................................134
Diagnostic Procedure ............................................134
DTC P1704 TRANSMISSION CONTROL MODULE
(EEPROM) ...............................................................135
Description ............................................................135
On Board Diagnosis Logic ....................................135
Possible Cause .....................................................135
DTC Confirmation Procedure ................................135
Diagnostic Procedure ............................................135
DTC P1705 THROTTLE POSITION SENSOR ........136
Description ............................................................136
CONSULT-II Reference Value ...............................136
On Board Diagnosis Logic ....................................136
Possible Cause .....................................................136
DTC Confirmation Procedure ................................136
Diagnostic Procedure ............................................136
DTC P1710 A/T FLUID TEMPERATURE SENSOR
CIRCUIT ..................................................................139
Description ............................................................139
CONSULT-II Reference Value ...............................139
On Board Diagnosis Logic ....................................139
Possible Cause .....................................................139
DTC Confirmation Procedure ................................139
Wiring Diagram — AT — FTS ...............................140
Diagnostic Procedure ............................................141
Component Inspection ..........................................142
DTC P1716 TURBINE REVOLUTION SENSOR ....143
Description ............................................................143
CONSULT-II Reference Value ...............................143
On Board Diagnosis Logic ....................................143
Possible Cause .....................................................143
DTC Confirmation Procedure ................................143
Diagnostic Procedure ............................................144
DTC P1721 VEHICLE SPEED SENSOR MTR .......145
Description ............................................................145
CONSULT-II Reference Value ...............................145
On Board Diagnosis Logic ....................................145
Possible Cause .....................................................145
DTC Confirmation Procedure ................................145
Diagnostic Procedure ............................................146
DTC P1730 A/T INTERLOCK .................................147
Description ............................................................147
On Board Diagnosis Logic ....................................147
Possible Cause .....................................................147
DTC Confirmation Procedure ................................147
Judgement of A/T Interlock ...................................147
Diagnostic Procedure ............................................148
DTC P1731 A/T 1ST ENGINE BRAKING ...............150
Description ............................................................150
CONSULT-II Reference Value ...............................150
On Board Diagnosis Logic ....................................150
Possible Cause .....................................................150
DTC Confirmation Procedure ................................150
Diagnostic Procedure ............................................151
DTC P1752 INPUT CLUTCH SOLENOID VALVE ..152
Description ............................................................152
CONSULT-II Reference Value ...............................152
On Board Diagnosis Logic ....................................152

INDEX FOR DTC
AT-5
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
INDEX FOR DTCPFP:00024
Alphabetical Index ACS0079V
NOTE:
If DTC “U1000” is displayed with other DTC, first perform the trouble diagnosis for “DTC U1000 CAN
COMMUNICATION LINE”. Refer to AT- 1 0 5
.
*1: These numbers are prescribed by SAE J2012.
*2: For VQ35DE engine.
*3: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL.Items
(CONSULT-II screen terms) DTC
Reference page OBD-II Except OBD-II
CONSULT-II (GST*1) CONSULT-II only “A/T”
A/T 1ST E/BRAKING — P1731AT- 1 5 0
ATF PRES SW 1/CIRC — P1841AT- 1 7 8
ATF PRES SW 3/CIRC — P1843AT- 1 8 0
ATF PRES SW 5/CIRC — P1845AT- 1 8 2
ATF PRES SW 6/CIRC — P1846AT- 1 8 4
A/T INTERLOCK P1730 P1730AT- 1 4 7
A/T TCC S/V FNCTN P0744 P0744 AT- 1 2 5
ATF TEMP SEN/CIRC P0710 P1710AT- 1 3 9
CAN COMM CIRCUIT U1000 U1000AT- 1 0 5
D/C SOLENOID/CIRC P1762 P1762AT- 1 6 0
D/C SOLENOID FNCTN P1764 (*3) P1764 AT- 1 6 2
ENGINE SPEED SIG P0725 (*2) P0725AT- 1 2 1
FR/B SOLENOID/CIRC P1757 P1757AT- 1 5 6
FR/B SOLENOID FNCT P1759 P1759 AT- 1 5 8
HLR/C SOL/CIRC P1767 P1767AT- 1 6 4
HLR/C SOL FNCTN P1769 (*3) P1769 AT- 1 6 6
I/C SOLENOID/CIRC P1752 P1752AT- 1 5 2
I/C SOLENOID FNCTN P1754 (*3) P1754 AT- 1 5 4
L/PRESS SOL/CIRC P0745 P0745AT- 1 2 7
LC/B SOLENOID/CIRC P1772 P1772AT- 1 6 8
LC/B SOLENOID FNCT P1774 P1774 AT- 1 7 0
MANU MODE SW/CIR — P1815AT- 1 7 2
PNP SW/CIRC P0705 P0705AT- 11 2
STARTER RELAY/CIRC — P0615AT- 1 0 8
TCC SOLENOID/CIRC P0740 P0740AT- 1 2 3
TCM·EEPROM — P1704AT- 1 3 5
TCM-POWER SUPPLY — P1701AT- 1 2 9
TCM·RAM — P1702AT- 1 3 3
TCM·ROM — P1703AT- 1 3 4
TP SEN/CIRC A/T P1705 (*2) P1705AT- 1 3 6
TURBINE REV S/CIRC P1716 P1716AT- 1 4 3
VEH SPD SE/CIR·MTR — P1721AT- 1 4 5
VEH SPD SEN/CIR AT P0720 P0720AT- 11 6

AT-6
INDEX FOR DTC
Revision: 2004 November 2004 FX35/FX45
DTC No. Index ACS0079W
NOTE:
If DTC “U1000” is displayed with other DTC, first perform the trouble diagnosis for “DTC U1000 CAN
COMMUNICATION LINE”. Refer to AT- 1 0 5
.
*1: These numbers are prescribed by SAE J2012.
*2: For VQ35DE engine.
*3: These malfunctions cannot be displayed MIL if another malfunction is assigned to MIL.DTC
Items
(CONSULT-II screen terms)Reference page OBD-II Except OBD-II
CONSULT-II GST (*1) CONSULT-II only “A/T”
— P0615 STARTER RELAY/CIRCAT-108
P0705 P0705 PNP SW/CIRCAT- 11 2
P0710 P1710 ATF TEMP SEN/CIRCAT-139
P0720 P0720 VEH SPD SEN/CIR ATAT- 11 6
P0725 (*2) P0725 ENGINE SPEED SIGAT-121
P0740 P0740 TCC SOLENOID/CIRCAT-123
P0744 P0744 A/T TCC S/V FNCTNAT-125
P0745 P0745 L/PRESS SOL/CIRCAT-127
— P1701 TCM-POWER SUPPLYAT-129
— P1702 TCM·RAMAT-133
— P1703 TCM·ROMAT-134
— P1704 TCM·EEPROMAT-135
P1705 (*2) P1705 TP SEN/CIRC A/TAT-136
P1716 P1716 TURBINE REV S/CIRCAT-143
— P1721 VEH SPD SE/CIR·MTRAT-145
P1730 P1730 A/T INTERLOCKAT-147
— P1731 A/T 1ST E/BRAKINGAT-150
P1752 P1752 I/C SOLENOID/CIRCAT-152
P1754 (*3) P1754 I/C SOLENOID FNCTNAT-154
P1757 P1757 FR/B SOLENOID/CIRCAT-156
P1759 (*3) P1759 FR/B SOLENOID FNCTAT-158
P1762 P1762 D/C SOLENOID/CIRCAT-160
P1764 (*3) P1764 D/C SOLENOID FNCTNAT-162
P1767 P1767 HLR/C SOL/CIRCAT-164
P1769 P1769 HLR/C SOL FNCTNAT-166
P1772 P1772 LC/B SOLENOID/CIRCAT-168
P1774 P1774 LC/B SOLENOID FNCTAT-170
— P1815 MANU MODE SW/CIRCAT-172
— P1841 ATF PRES SW 1/CIRCAT-178
— P1843 ATF PRES SW 3/CIRCAT-180
— P1845 ATF PRES SW 5/CIRCAT-182
— P1846 ATF PRES SW 6/CIRCAT-184
U1000 U1000 CAN COMM CIRCUITAT-105

PRECAUTIONS
AT-9
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
Service Notice or PrecautionsACS002L7
ATF COOLER SERVICE
If A/T fluid contains frictional material (clutches, bands, etc.), or if an A/T is repaired, overhauled, or replaced,
inspect and clean the A/T fluid cooler mounted in the radiator or replace the radiator. Flush cooler lines using
cleaning solvent and compressed air after repair. For A/T fluid cooler cleaning procedure, refer to AT- 1 4 , "
A/T
Fluid Cooler Cleaning" . For radiator replacement, refer to CO-14, "RADIATOR" (for VQ35DE) or CO-39,
"RADIATOR" (for VK45DE).
OBD-II SELF-DIAGNOSIS

A/T self-diagnosis is performed by the TCM in combination with the ECM. The results can be read through
the blinking pattern of the A/T CHECK indicator or the malfunction indicator lamp (MIL). Refer to the table
on AT- 9 4 , "
SELF-DIAGNOSTIC RESULT MODE" for the indicator used to display each self-diagnostic
result.

The self-diagnostic results indicated by the MIL are automatically stored in both the ECM and TCM mem-
ories.
Always perform the procedure on AT- 3 9 , "
HOW TO ERASE DTC" to complete the repair and avoid
unnecessary blinking of the MIL.
For details of OBD-II, refer to EC-53, "
ON BOARD DIAGNOSTIC (OBD) SYSTEM" (for VQ35DE) or EC-703,
"ON BOARD DIAGNOSTIC (OBD) SYSTEM" (for VK45DE).

Certain systems and components, especially those related to OBD, may use the new style slide-
locking type harness connector. For description and how to disconnect, refer to PG-74, "
HAR-
NESS CONNECTOR" .
Wiring Diagrams and Trouble DiagnosisACS002L8
When you read wiring diagrams, refer to the following:

GI-15, "How to Read Wiring Diagrams".

PG-3, "POWER SUPPLY ROUTING CIRCUIT" for power distribution circuit.
When you perform trouble diagnosis, refer to the following:

GI-11, "How to Follow Trouble Diagnoses".

GI-27, "How to Perform Efficient Diagnosis for an Electrical Incident".

PREPARATION
AT-11
D
E
F
G
H
I
J
K
L
MA
B
AT
Revision: 2004 November 2004 FX35/FX45
Commercial Service ToolsACS0079Y
Tool nameDescription
Power toolLoosening bolts and nuts
Drift
a: 22mm (0.87 in) dia.Installing manual shaft oil seals
Drift
a: 64 mm (2.52 in) dia.Installing rear oil seal (AWD models)
PBIC0190E
NT083
SCIA5338E