2004 DAEWOO NUBIRA lock

1F – 44IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
39Repair the open or short circuit the following termi-
nals.
S Terminal 6 of ECM and terminal 86 of fuel
pump relay.
S Terminal 87 of fuel pump relay and terminal
3 of fuel pump.
Is the repair complete?–Go to Step 2–
40Replace the fuel pump relay.
Is the repair complete?–Go to Step 2–
411. Turn the ignition OFF.
2. Disconnect the fuel inject harness connectors
from all of the fuel injectors.
3. Turn the ignition ON.
4. Connect test light between fuel injector harness
connector 2 and ground.
5. Repeat step 4 for each of the remaining fuel
injectors.
Does the test light on at all of the fuel injectors?–Go to Step 42Go to Step 45
421. Turn the ignition OFF.
2. Connect test light between fuel injector harness
connector 1 and battery positive.
3. Crank the engine.
4. Repeat step 2 and 3 for each of the remaining
fuel injectors.
Does the test light flash for all of the fuel injectors?–Go to Step 43Go to Step 46
43Measure the resistance of each fuel injectors.
Is the resistance within the value specified.
Notice : the resistance will increase slightly at higher
temperature.11.6–12.4WSystem OKGo to Step 44
44Replace any of the fuel injectors with a resistance
out of specification.
Is the repair complete?–Go to Step 2–
451. Inspect the fuse EF22 in engine fuse block.
2. Check for an open between the circuit from
terminal 2 of the four fuel injectors and terminal
87 of main relay.
Is the problem found?–Go to Step 48Go to
”Main Relay
Circuit Check”
46Measure the resistance between following termi-
nals.
S Terminal 2 of injector 1 connector and terminal
59 of ECM connector.
S Terminal 2 of injector 2 connector and terminal
90 of ECM connector.
S Terminal 2 of injector 3 connector and terminal
60 of ECM connector.
S Terminal 2 of injector 4 connector and terminal
89 of ECM connector.
Does the resistance within the specified value?0 WGo to Step 49Go to Step 47
47Repair the open fuel injector harness wire(s).
Is the repair complete?–Go to Step 2–

1F – 54IENGINE CONTROLS
DAEWOO V–121 BL4
NO MALFUNCTION INDICATOR LAMP (1.4L/1.6L DOHC)
Circuit Description
When the ignition is turned ON, the Malfunction Indicator
Lamp (MIL) will be turned ON and remain ON until the en-
gine is running, if no Diagnostic Trouble Codes (DTCs) are
stored. Battery voltage is supplied through the ignition
switch directly to the MIL telltale. The Engine Control Mod-
ule (ECM) controls the MIL by providing a ground path
through the MIL control circuit to turn ON the MIL.
Diagnostic Aids
An open ignition fuse F4 will cause the entire cluster to beinoperative.
Check the battery and ignition feed circuits for poor con-
nections if the MIL is intermittent.
Any circuitry, that is suspected as causing an intermittent
complaint, should be thoroughly checked for backed–out
terminals, improper mating, broken locks, improperly
formed or damaged terminals, poor terminal–to–wiring
connections or physical damage to the wiring harness.

ENGINE CONTROLS 1F – 55
DAEWOO V–121 BL4
No Malfunction Indicator Lamp (1.4L/1.6L DOHC)
StepActionValue(s)YesNo
1Attempt to start the engine.
Does the engine start?–Go to Step 2Go to
”Engine Cranks
But Will Not
Run”
21. Turn the ignition switch to LOCK.
2. Disconnect the Engine Control Module (ECM)
connector.
3. Turn the ignition switch to ON.
4. Connect a test light between the ECM connec-
tor terminal 39 and ground.
Is the test light illuminate?–Go to Step 3Go to Step 6
3Check terminals for damage or poor connection.
Does any problem found?–Go to Step 5Go to Step 4
4Replace the ECM.
Is the replacement complete?–Go to
”On–Board
Diagnostic Sys-
tem Check”–
5Repair any damaged terminals or poor connection.
Is the repair complete?–Go to
”On–Board
Diagnostic Sys-
tem Check”–
6Check the fuse F4.
Is the fuse open?Go to Step 7Go to Step 8
71. Check for a short to ground in the circuit and
repair as needed.
2. Replace the fuse F4.
Is the repair or replacement complete?–Go to
”On–Board
Diagnostic Sys-
tem Check”–
81. Check for an open circuit between fuse F4 and
the ECM connector terminal 39 and repair as
needed.
2. Check the MIL bulb and replace if open.
Is the repair or replacement complete?–Go to
”On–Board
Diagnostic Sys-
tem Check”–

1F – 56IENGINE CONTROLS
DAEWOO V–121 BL4
NO MALFUNCTION INDICATOR LAMP (1.8L DOHC)
Circuit Description
When the ignition is turned ON, the Malfunction Indicator
Lamp (MIL) will be turned ON and remain ON until the en-
gine is running, if no Diagnostic Trouble Codes (DTCs) are
stored. Battery voltage is supplied through the ignition
switch directly to the MIL telltale. The Engine Control Mod-
ule (ECM) controls the MIL by providing a ground path
through the MIL control circuit to turn ON the MIL.
Diagnostic Aids
An open ignition fuse F4 will cause the entire cluster to be
inoperative.
Check the battery and ignition feed circuits for poor con-
nections if the MIL is intermittent.Any circuitry, that is suspected as causing an intermittent
complaint, should be thoroughly checked for backed–out
terminals, improper mating, broken locks, improperly
formed or damaged terminals, poor terminal–to–wiring
connections or physical damage to the wiring harness.
Test Description
Number(s) below refer to the step(s) on the diagnostic
table.
1. If the engine fails to start and the MIL is inopera-
tive, then the fault can be isolated to either the
ECM ignition feed. The battery feed, or a poor
ground at the engine block, or the ECM.
2. Probing the MIL circuit with a test light to ground
stimulates the ECM’s control of the MIL. If the MIL
illuminates, then the malfunction can be isolated to
the control of the MIL or a poor connection at the
MIL terminal to the ECM.

ENGINE CONTROLS 1F – 57
DAEWOO V–121 BL4
No Malfunction Indicator Lamp (1.8L DOHC)
StepActionValue(s)YesNo
1Attempt to start the engine.
Does the engine start?–Go to Step 2Go to
”Engine Cranks
But Will Not
Run”
21. Turn the ignition switch to LOCK.
2. Disconnect the Engine Control Module (ECM)
connector.
3. Turn the ignition switch to ON.
4. Connect a test light between the ECM connec-
tor terminal K64 and ground.
Is the test light illuminate?–Go to Step 3Go to Step 6
3Check terminals for damage or poor connection.
Does any problem found?–Go to Step 5Go to Step 4
4Replace the ECM.
Is the replacement complete?–Go to
”On Board
Diagnostic Sys-
tem Check”–
5Repair any damaged terminals or poor connection.
Is the repair complete?–Go to
”On Board
Diagnostic Sys-
tem Check”–
6Check the fuse F4.
Is the fuse open?Go to Step 7Go to Step 8
71. Check for a short to ground in the circuit and
repair as needed.
2. Replace the fuse F4.
Is the repair or replacement complete?–Go to
”On Board
Diagnostic Sys-
tem Check”
81. Check for an open circuit between fuse F4 and
the ECM connector terminal K64 and repair as
needed.
2. Check the MIL bulb and replace if open.
Is the repair or replacement complete?–Go to
”On Board
Diagnostic Sys-
tem Check”–

ENGINE CONTROLS 1F – 59
DAEWOO V–121 BL4
Malfunction Indicator Lamp On Steady (1.4L/1.6L DOHC)
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) system
check.
Is the check complete.–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition switch to LOCK.
2. Install the scan tool to the Data Link Connector
(DLC).
3. Command the Malfunction Indicator Lamp
(MIL) ON and OFF.
Does the MIL turn ON and OFF when commanded?–Go to Step 7Go to Step 3
31. Turn the ignition switch to LOCK.
2. Disconnect the Engine Control Module (ECM)
connector.
3. Turn the ignition switch to ON.
Is the MIL off?–Go to Step 6Go to Step 4
4Check the MIL control circuit for a short to ground
and repair as needed.
Is the repair complete?–Go to Step 7Go to Step 5
5Replace the instrument panel cluster. Refer to Sec-
tion 9E, Instrumentation/Driver Information.
Is the repair complete?–Go to Step 7–
6Replace the ECM.
Is the repair complete?–Go to Step 7–
71. Using the scan tool, clear the Diagnostic
Trouble Codes(DTCs).
2. Attempt to start the engine.
Does the engine start and continue to run?–Go to Step 8Go to Step 1
81. Allow the engine to idle until normal operating
temperature is reached.
2. Check if any DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

ENGINE CONTROLS 1F – 61
DAEWOO V–121 BL4
Malfunction Indicator Lamp On Steady (1.8L DOHC)
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) system
check.
Is the check complete.–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Turn the ignition switch to LOCK.
2. Install the scan tool to the Data Link Connector
(DLC).
3. Command the Malfunction Indicator Lamp
(MIL) ON and OFF.
Does the MIL turn ON and OFF when commanded?–Go to Step 7Go to Step 3
31. Turn the ignition switch to LOCK.
2. Disconnect the Engine Control Module (ECM)
connector.
3. Turn the ignition switch to ON.
Is the MIL off?–Go to Step 6Go to Step 4
4Check the MIL control circuit for a short to ground
and repair as needed.
Is the repair complete?–Go to Step 7Go to Step 5
5Replace the instrument panel cluster. Refer to
Section 9E, Instrumentation/Driver Information.
Is the repair complete?–Go to Step 7–
6Replace the ECM.
Is the repair complete?–Go to Step 7–
71. Using the scan tool, clear the Diagnostic
Trouble Codes(DTCs).
2. Attempt to start the engine.
Does the engine start and continue to run?–Go to Step 8Go to Step 1
81. Allow the engine to idle until normal operating
temperature is reached.
2. Check if any DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
” Applicable
DTC table”System OK

ENGINE CONTROLS 1F – 71
DAEWOO V–121 BL4
MAIN RELAY CIRCUIT CHECK (1.4L/1.6L DOHC)
Circuit Description
When the ignition is turned On or to the START position,
the main relay is energized. The main relay then supply
voltage to the engine fuse block fuse Ef11. The Electronic
Ignition (EI) system ignition coil, Evaporative Emission
(EVAP) Canister Purge Solenoid and Heated Oxygen
Sensor (HO2S) are supplied voltage through the engine
fuse block fuse Ef11. The fuel injectors are supplied volt-
age through the engine fuse block fuse Ef11.Diagnostic Aids
S An intermittent problem may be caused by a poor
connection, rubbed through wire insulation, or a
broken wire inside the insulation.
S A fault main relay will cause a no start condition.
There will be no voltage supplied to the EI system
ignition coil, or the fuel injectors. Without voltage
supplied to these components, they will not oper-
ate.
Main Relay Circuit Check (1.4L/1.6L DOHC)
StepActionValue(s)YesNo
11. Turn the ignition OFF.
2. Disconnect the engine fuse block fuse Ef11.
3. Turn the ignition ON.
4. With a test light connected to the ground,
probe the fuse terminals nearest the main relay
for fuse Ef11.
Is the light on at both terminal?–System OKGo to Step 2
2Is the light on at only one terminal?–Go to Step 3Go to Step 4
3Repair the open in the wiring between the main relay
connector terminal 87 and the fuse Ef11.
Is the repair complete?–System OK–