0B – 12IGENERAL INFORMATION
DAEWOO V–121 BL4
OWNER INSPECTIONS AND SERVICES
WHLE OPERATING THE VEHICLE
Horn Operation
Blow the horn occasionally tomake sure it works. Check
all the button locations.
Brake System Operation
Be alert for abnormal sounds, increased brake pedal trav-
el or repeated pulling to one side when braking. Also, if the
brake warning light goes on, or flashes, something may be
wrong with part of the brake system.
Exhaust System Operation
Be alert to any changes in the sound of the system or the
smell of the fumes. These are signs that the system may
be leaking or overheating. Have the system inspected and
repaired immediately.
Tires,Wheels and Alignment Operation
Be alert to any vibration of the steering wheel or the seats
at normal highway speeds. This may mean a wheel needs
to be balanced. Also, a pull right or left on a straight, level
road may show the need for a tire pressure adjustment or
a wheel alignment.
Steering System Operation
Be alert to changes in the steering action. An inspection
is needed when the steering wheel is hard to turn or has
too much free play, or if unusual sounds are noticed when
turning or parking.
Headlight Aim
Take note of the light pattern occasionally. Adjust the
headlights if the beams seem improperly aimed.
AT EACH FUEL FILL
A fluid loss in any (except windshield washer) system may
indicate a problem. Have the system inspected and re-
paired immediately.
Engine Oil Level
Check the oil level and add oil if necessary. The best time
to check the engine oil level is when the oil is warm.
1. After stopping the engine, wait a few minutes for
the oil to drain back to the oil pan.
2. Pull out the oil level indicator (dip stick).
3. Wipe it clean, and push the oil level indicator back
down all the way.
4. Pull out the oil level indicator and look at the oil lev-
el on it.
5. Add oil, if needed, to keep the oil level above the
MIN line and within the area labeled ”Operating
Range.” Avoid overfilling the engine, since this may
cause engine damage.
6. Push the indicator all the way back down into the
engine after taking the reading.If you check the oil level when the oil is cold, do not run the
engine first. The cold oil will not drain back to the pan fast
enough to give a true oil level reading.
Engine Coolant Level and Condition
Check the coolant level in the coolant reservoir tank and
add coolant if necessary. Inspect the coolant. Replace
dirty or rusty coolant.
Windshield Washer Fluid Level
Check the washer fluid level in the reservoir. Add fluid if
necessary.
AT LEAST MONTHLY
Tire And Wheel Inspection and Pressure
Check
Check the tires for abnormal wear or damage. Also check
for damaged wheels. Check the tire pressure when the
tires are cold (check the spare also, unless it is a stow-
away). Maintain the recommended pressures that are on
the tire placard that is in the glove box.
Light Operation
Check the operation of the license plate light, the head-
lights (including the high beams), the parking lights, the
fog lights, the taillight, the brake lights, the turn signals, the
backup lights and the hazard warning flasher.
Fluid Leak Check
Periodically inspect the surface beneath the vehicle for
water, oil, fuel or other fluids, after the vehicle has been
parked for a while. Water dripping from the air conditioning
system after use is normal. If you notice fuel leaks or
fumes, find the cause and correct it at once.
AT LEAST TWICE A YEAR
Power Steering System Reservoir Level
Check the power steering fluid level. Keep the power
steering fluid at the proper level. Refer to Section 6A, Pow-
er Steering System.
Brake Master Cylinder Reservoir Level
Check the fluid and keep it at the proper level. A low fluid
level can indicate worn disc brake pads which may need
to be serviced. Check the breather hole in the reservoir
cover to be free from dirt and check for an open passage.
Clutch Pedal Free Travel
Check clutch pedal free travel and adjust as necessary.
Measure the distance from the center of the clutch pedal
to the outer edge of the steering wheel with the clutch ped-
al not depressed. Then measure the distance from the
center of the clutch pedal to the outer edge of the steering
wheel with the clutch pedal fully depressed. The difference
between the two values must be greater than 130 mm
(5.19 inches).
Weather–Strip Lubrication
Apply a thin film silicone grease using a clean cloth.
ANTILOCK BRAKE SYSTEM 4F – 47
DAEWOO V–121 BL4
J3B14F10
EBCM
ORN/
BLK
LT BLULT B L U
BLK/ WHT
C201 C202
141
40
19
61
G1062
4
15A Ef13
6
C10211
S30114
C201C110
76
C202 11
DIAGNOSTIC TROUBLE CODE (DTC) C0161
ABS BRAKE SWITCH CIRCUIT MALFUNCTION
Circuit Description
When the brake pedal is depressed, the contacts on the
brake light switch close to illuminate the brake lights. Bat-
tery voltage is also applied to terminal 14 of the electronic
brake control module (EBCM), which signals the ABS con-
troller that the brakes are applied and ABS may be need-
ed. Without this, signals from a wheel speed sensor that
may indicate need for ABS intervention are questionable.
When the brake pedal is not depressed, the EBCM termi-
nal 14 is grounded through the brake lights.
Diagnosis
This procedure will check whether there is no output or
constant output from the brake light switch and will deter-
mine the cause as a faulty switch or a problem in the cir-
cuitry.
Cause(s)
S The ground connection or the positive connection at
the EBCM has failed.
S There is an open, short to ground, or short to posi-
tive in the vehicle wiring.S The brake light switch has failed.
Fail Action
The system records a DTC C0161. ABS and EBD opera-
tion is enabled and ABS / EBD warning lamp don’t turn on.
Test Description
The number(s) below refer to step(s) on the diagnostic
table.
1. This simple test will isolate the problem to the fuse–
brake light switch–splice 301 area or the splice
301–EBCM area.
3. This is the first step in identifying an open, a short
to ground, a short to voltage, or a faulty brake light
switch.
11. This step begins the process of finding an open, a
defective connector, or a faulty EBCM.
Diagnostic Aids
Inspect wiring and connectors carefully and thoroughly.
Failure to do so could result in misdiagnosis, causing part
replacement with reappearance of the malfunction.
