2004 DAEWOO LACETTI Rod

1F – 302IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P1382
ROUGH ROAD DATA INVALID (ABS)
Circuit Description
The wheel speed sensor is used to detecting the road situ-
ation.
As the wheel is rotated, the wheel speed sensor produces
an AC voltage that increase with wheel speed. The EBCM
uses the frequency of the AC signal to calculate wheel
speed. The wheel speed sensor is connected to EBCM by
a ”twisted pair” of wires. Twisting reduces noise suscepti-
bility than may cause a DTC to set. If the wheel speed sen-
sor detects a rough road condition, the ECM misfire detec-
tion diagnostic will be de–activated.
Conditions for Setting the DTC
S Vehicle speed is higher than 5km/h(3.1mph).
S No Vehicle Speed Sensor error not set.
S VR sensor output signal is higher than 0.26.S VR sensor output signal is not change for 30sec-
onds.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will not illumi-
nate.
S The ECM will store conditions which were present
when the DTC was set as Failure Records data
only.
S This information will not be stored in the Freeze
Frame data.
Conditions for Clearing the MIL/DTC
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.

1F – 372IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0131
FRONT HEATED OXYGEN SENSOR (HO2S1) LOW
VOLTAGE
Circuit Description
The Engine Control Module (ECM) supplies a voltage of
about 0.45 volts between terminals M12 and M29 (if mea-
sured with a 10 megohm digital voltmeter, this may read
as low as 0.32 volts). The Front Heated Oxygen sensor 1
(HO2S1) varies the voltage within a range of about 1 volt
if the exhaust is rich, down through about 0.10 volts if the
exhaust is lean.
The sensor is like an open circuit and produces no voltage
when it is below 315°C(600°F). An open sensor circuit or
cold sensor causes Open Loop operation.
If the HO2S1 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S1 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S1 wire(s). Any attempt to
repair the wires, connector or terminals could result in the
obstruction of the air reference and degrade the HO2S1
performance. Refer to ”Front Heated Oxygen Sensor” in
this section.Conditions for Setting the DTC
S HO2S1 voltage is less than 0.05 volts.
S Closed loop stoichiometry.
S Engine Coolant Temperature (ECT) is greater than
60°C(140°F).
S System voltage is greater than 10 volts.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0402, P0404, P0405, P0406, P0506,
P0507, P1404, and P0443 are not set.
S 3 second delay after conditions are met.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The vehicle will operate in Open Loop.

ENGINE CONTROLS 1F – 375
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0132
FRONT HEATED OXYGEN SENSOR (HO2S1) HIGH
VOLTAGE
Circuit Description
The Engine Control Module (ECM) supplies a voltage of
about 0.45 volts between terminals M12 and M29 (if mea-
sured with a 10 megohm digital voltmeter, this may read
as low as 0.32 volts). The Front Heated Oxygen Sensor
(HO2S1) varies the voltage within a range of about 1 volt
if the exhaust is rich, down through about 0.10 volts if the
exhaust is lean.
The sensor is like and open circuit and produces no volt-
age when it is below 315°C (600°F). An open sensor cir-
cuit or cold sensor causes Open Loop operation.
If the HO2S1 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S1 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S1 wire(s). Any attempt to
repair the wires, connector or terminals could result in the
obstruction of the air reference and degrade the HO2S1
performance. Refer to”Front Heated Oxygen Sensor” in
this section.
Conditions for Setting the DTCS HO2S1 voltage is greater than 0.952 volts.
S Closed loop stoichiometry.
S Engine Coolant Temperature (ECT) is greater than
60°C(140°F).
S System voltage is greater than 10 volts.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0402, P0404, P0405, P0406, P0506,
P0507, P1404, and P0443 are not set.
S 3 second delay after conditions are met.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The vehicle will operate in Open Loop.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

1F – 382IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0134
FRONT HEATED OXYGEN SENSOR (HO2S1) NO
ACTIVITY OR OPEN
Circuit Description
The Engine Control Module (ECM) supplies a voltage of
about 0.45 volts between terminals M12 and M29 (if mea-
sured with a 10 megohm digital voltmeter, this may read
as low as 0.32 volts). The Front Heated Oxygen Sensor
(HO2S1) varies the voltage within a range of about 1 volt
if the exhaust is rich, down through about 0.10 volts if the
exhaust is lean.
The sensor is like and open circuit and produces no volt-
age when it is below 315 °C (600 °F). An open sensor cir-
cuit or cold sensor causes Open Loop operation.
If the HO2S1 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S1 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S1 wire(s). Any attempt to
repair the wires, connector or terminals could result in the
obstruction of the air reference and degrade the HO2S1
performance. Refer to”Front Heated Oxygen Sensor
(HO2S1)” in this section.Conditions for Setting the DTC
S HO2S1 voltage is between 420 and 480 mV.
S Engine Coolant Temperature (ECT) is greater than
60 °C (140 °F)
S System voltage is greater than 10 volts.
S Engine run time is greater than 60 seconds.
S Airflow is greater than 8 g/sec.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0402, P0404, P0405, P0406, P0506,
P0507, P1404, and P0443 are not set.
S 3 second delay after exiting Decel Fuel Cut–off
(DFCO) mode.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illumi-
nate.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
S The vehicle will operate in Open Loop.

1F – 388IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0137
REAR HEATED OXYGEN SENSOR (HO2S2) LOW
VOLTAGE
Circuit Description
In order to control emissions, a catalytic converter is used
to convert harmful emissions into harmless water vapor
and carbon dioxide.
The Engine Control Module (ECM) has the ability to moni-
tor this process by using a Rear Heated Oxygen Sensor
(HO2S2). The HO2S2, located in the exhaust stream past
the catalytic converter, produces an output signal which in-
dicates the storage capacity of the catalyst. This in turn in-
dicates the catalyst’s ability to convert exhaust emissions
effectively. If the catalyst is functioning properly, the
HO2S2 signal will be far less active than the signal pro-
duced by the Front Heated Oxygen Sensor (HO2S1).
If the HO2S2 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S2 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S2 wire(s). Any attempt to
repair the wires, connector, or terminals could result in the
obstruction of the air reference and degrade the HO2S2
performance.Conditions for Setting the DTC
S HO2S2 voltage is less than 0.05 volt in Closed
Loop control or less than 0.35 volt in Power Enrich-
ment (PE) mode.
S Engine Coolant Temperature (ECT) is greater than
60°C (140°F).
S System voltage is greater than 10 volts.
S Closed Loop test: 3 seconds delay after in Closed
Loop and air flow is greater than 9 g/sec.
S Power Enrichment test: Air/Fuel ration is less than
or equal to 13.5 and 3 seconds delay after in Power
Enrichment mode.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0141, P0402, P0404, P0405, P0406,
P0506, P0507, P1404, and P0443 are not set.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.

ENGINE CONTROLS 1F – 391
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0138
REAR HEATED OXYGEN SENSOR (HO2S2) HIGH
VOLTAGE
Circuit Description
In order to control emissions, a catalytic converter is used
to convert harmful emissions into harmless water vapor
and carbon dioxide.
The Engine Control Module (ECM) has the ability to moni-
tor this process by using a Rear Heated Oxygen Sensor
(HO2S2). The HO2S2, located in the exhaust stream past
the catalytic converter, produces an output signal which in-
dicates the storage capacity of the catalyst. This in turn in-
dicates the catalyst¡¯s ability to convert exhaust emissions
effectively. If the catalyst is functioning properly, the
HO2S2 signal will be far less active than the signal pro-
duced by the Front Heated Oxygen Sensor (HO2S1).
If the HO2S2 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S2 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S2 wire(s). Any attempt to
repair the wires, connector, or terminals could result in the
obstruction of the air reference and degrade the HO2S2
performance.Conditions for Setting the DTC
S HO2S2 voltage is greater than 0.952 volt in Closed
Loop control or greater than 0.55 volt in Decel Fuel
Cutoff (DFCO) mode.
S Engine Coolant Temperature (ECT) is greater than
60°C (140°F).
S System voltage is greater than 10 volts.
S Closed Loop test: 3 seconds delay after in Closed
Loop and airflow is greater than 9 g/sec.
S DFCO test: 2 seconds delay after in DFCO.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0141, P0402, P0404, P0405, P0406,
P0506, P0507, P1404, and P0443 are not set.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.

1F – 394IENGINE CONTROLS
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0140
REAR HEATED OXYGEN SENSOR (HO2S2) NO ACTIVITY
OR OPEN
Circuit Description
In order to control emissions, a catalytic converter is used
to convert harmful emissions into harmless water vapor
and carbon dioxide.
The Engine Control Module (ECM) has the ability to moni-
tor this process by using a Rear Heated Oxygen Sensor
(HO2S2). The HO2S2, located in the exhaust stream past
the catalytic converter, produces an output signal which in-
dicates the storage capacity of the catalyst. This in turn in-
dicates the catalyst is ability to convert exhaust emissions
effectively. If the catalyst is functioning properly, the
HO2S2 signal will be far less active than the signal pro-
duced by the Front Heated Oxygen Sensor (HO2S1).
If the HO2S2 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S2 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S2 wire(s). Any attempt to
repair the wires, connector, or terminals could result in the
obstruction of the air reference and degrade the HO2S2
performance.Conditions for Setting the DTC
S HO2S2 voltage is between 0.422 and 0.478 volts.
S Engine Coolant Temperature (ECT) is greater than
60°C (140°F).
S Engine rum time is greater than 60 seconds.
S System voltage is greater than 10 volts.
S Closed Loop stoichiometry.
S 3 second delay after exiting Decel Fuel Cutoff
(DFCO) mode.
S DTCs P0106, P0107, P0108, P0117, P0118,
P0122, P0123, P0171, P0172, P0201, P0202,
P0203, P0204, P0300, P0336, P0337, P0351,
P0352, P0141, P0402, P0404, P0405, P0406,
P0506, P0507, P1404, and P0443 are not set.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC

ENGINE CONTROLS 1F – 397
DAEWOO V–121 BL4
DIAGNOSTIC TROUBLE CODE (DTC) P0141
REAR HEATED OXYGEN SENSOR (HO2S2) HEATER
CIRCUIT NOT FUNCTIONING
Circuit Description
In order to control emissions, a catalytic converter is used
to convert harmful emissions into harmless water vapor
and carbon dioxide.
The Engine Control Module (ECM) has the ability to moni-
tor this process by using a Rear Heated Oxygen Sensor
(HO2S2). The HO2S2, located in the exhaust stream past
the catalytic converter, produces an output signal which in-
dicates the storage capacity of the catalyst. This in turn in-
dicates the catalyst is ability to convert exhaust emissions
effectively. If the catalyst is functioning properly, the
HO2S2 signal will be far less active than the signal pro-
duced by the Front Heated Oxygen Sensor (HO2S1).
If the HO2S2 pigtail wiring, connector, or terminal is dam-
aged, the entire HO2S2 assembly must be replaced. Do
not attempt to repair the wiring, connector, or terminals. In
order for the sensor to function properly, it must have a
clean air reference provided to it. This clean air reference
is obtained by way of the HO2S2 wire(s). Any attempt to
repair the wires, connector, or terminals could result in the
obstruction of the air reference and degrade the HO2S2
performance.The ECM will check if HO2S2 is functioning properly by
monitoring the current to HO2S2 heater. If the current is
less than 0.1 ampere, DTC P0141 will set.
Conditions for Setting the DTC
S HO2S2 heater current is less than 0.1 amperes.
S Engine rum time is greater than 60 seconds.
S System voltage is greater than 10 volts.
Action Taken When the DTC Sets
S The Malfunction Indicator Lamp (MIL) will illuminate
after three consecutive ignition cycle with a fail.
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.