2004 DAEWOO LACETTI brake

AISIN AUTOMATIC TRANSAXLE 5A2 – 145
DAEWOO V–121 BL4
36. Using 1st & reverse brake adapter DW240–070 and
brake spring compressor bolt/nut DW240–060–01,
install the snap ring.
Notice : Make sure that the snap ring is installed in the
groove of the transaxle case correctly.
37. Using a dial indicator, measure the 1st & reverse
brake piston stroke while applying and releasing
392–785 kPa (57–114 psi) of compressed air.
Notice : If the piston stroke is non–standard, inspect the
discs, plates and flange. Piston stroke 0.6
1.3 mm (0.024

0.051 in.)
38. Using counter drive gear installation adapter
DW240–100, brake spring compressor bolt/nut
DW240–060–01 and brake spring compressor plate
DW240–060–02, install the counter drive gear.
Notice : Be careful not to apply excessive force to the
transaxle case.
39. Coat a new oil seal with ATF.
40. Install the oil seal to the transaxle case.
S Oil seal in depth:
A: 1 ± 0.25 mm (0.39 ± 0.0098 in.)

5A2 – 148IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
50. Install the parking lock pawl bracket with the 2
bolts.
Tighten
Tighten the bolts to 7.4 NSm (65 lb–in).
51. Using counter drive gear installation adapter
DW240–100 and brake spring compressor bolt/nut
DW240–060–01,install the planetary ring gear.
S Before installing the planetary ring gear, be sure
to replace the planetary ring flange of the plane-
tary ring gear with a new one.
52. Fix the counter drive gear with parking lock pawl.
53. Using planetary ring gear nut removal/installation
socket DW260–041, install a new nut.
Tighten
Tighten the nut to 9.8 NSm (87 lb–in).

5A2 – 150IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
59. Check that the planetary gear turns freely counter-
clockwise and locks clockwise.
60. Install the anti–rattle clip in the place shown in the
illustration (the space between the No.2 one–way
clutch outer race and transaxle case), push the
anti–rattle clip in until you hear the ”click”.
61. Using vernier calipers, measure the free length of
the 2nd brake piston return spring together with
spring seat.
S Standard free length: 15.85 mm (0.6240 in.).
62. Check to see if the sliding surface of the disc, plate
and flange of 2nd brake are worn or burnt. If neces-
sary, replace them.
Notice : If the lining of the disc is peeling off or discolored,
or even if a part of the groove is defaced, replace all discs.
Notice : Before assembling new discs, soak them in ATF
for at least 15 minutes.

AISIN AUTOMATIC TRANSAXLE 5A2 – 151
DAEWOO V–121 BL4
63. Install the flange, 2 discs and 2 plates.
S Install in order : F
D
P
D
P
(D = Disc, P = Plate, F = Flange)
64. Install the 2nd brake return spring.
Notice : Make sure that the snap ring is installed in the
groove of the transaxle case correctly.
65. Coat 2 new O–rings with ATF, install them to the
2nd brake piston.
66. Install the 2nd brake piston into the 2nd brake
clutch cylinder.
Notice : Be careful not to damage the O–rings.
67. Install the 2nd brake clutch cylinder to the transaxle
case.

5A2 – 152IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
68. Using brake spring compressor bolt / nut
DW240–060–01 and 2nd brake adapter
DW240–080, compress the 2nd brake piston return
spring.
69. Using a screwdriver, install the snap ring.
Notice : Make sure that the snap ring is installed in the
groove of the transaxle case correctly.
70. Coat the thrust bearing race with petroleum jelly
and install it onto the front planetary sun gear.
S Race:
Inner diameter: 19.3 mm (0.760 in.)
Outer diameter : 29.0 mm (1.142 in.)
71. Install the front planetary sun gear to the transaxle
case.
72. Install the thrust washer and one–way clutch as-
sembly to the rear planetary sun gear.

AISIN AUTOMATIC TRANSAXLE 5A2 – 155
DAEWOO V–121 BL4
81. Check to see if the sliding surface of the disc, plate
and flange of 2nd coast & O/D brake are worn or
burnt. If necessary, replace them.
Notice : If the lining of the disc is peeling off or discolored,
or even if a part of the printed mark is defaced, replace all
discs.
Notice : Before assembly new discs, soak them in ATF for
at least 15 minutes.
82. Using a screwdriver, install the snap ring to the
transaxle case.
Notice : Make sure that the snap ring is installed in the
groove of the transaxle case correctly.
83. Install the flange, 2 discs and 2 plates to the trans-
axle case.
S Install in order: P
D
P
D
F
(P = Plate, D = Disc, F = Flange)
84. Clean the connected part the transaxle case and
transaxle rear cover.
85. As shown in the illustration, place a straight edge
on the transaxle case and measure the distance
between the 2nd coast & O/D brake flange and
straight edge using vernier calipers. (Dimension A).

5A2 – 156IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
86. As shown in the illustration, place a straight edge
on the O/D brake piston and measure the distance
between the transaxle rear cover and straight edge
using vernier calipers. (Dimension B).
87. Calculate the piston stroke value using the following
formula. Select a flange which satisfies the piston
stroke value and install it.
Piston stroke = Dimension A
Dimension B
Piston stroke : 0.65
1.05 mm (0.0256
0.0413
in.)
S Flange thickness : mm (in.)
Piston stroke
value
ThicknessMark
0.738 ~ 0.949
(0.02905 ~
0.03736)3.0
(0.118)0
0.950 ~ 1.149
(0.03740 ~
0.04524)3.2
(0.126)1
1.150 ~ 1.349
(0.04528 ~
0.05311)3.4
(0.134)2
1.350 ~ 1.549
(0.05315 ~
0.06098)3.6
(0.142)3
1.550 ~ 1.702
(0.06102 ~
0.06701)3.8
(0.150)0
88. Install new 4 apply gaskets to the transaxle rear
cover.
89. Coat the thrust neddle roller bearing with petroleum
jelly and install it onto the forward & reverse clutch
assembly.
S Bearig:
Inner diameter: 43.2 mm (1.701 in.)
Outer diameter: 62.0 mm (2.441 in.)
90. Remove any packing material and be careful not to
get oil on the contacting surfaces of the transaxle
rear cover or transaxle case.

AISIN AUTOMATIC TRANSAXLE 5A2 – 161
DAEWOO V–121 BL4
109. Coat new 6 O–rings with ATF and install them
to the pistons.
110. Coat the 3 springs and 3 accumulator pistons
with ATF, install them to the holes.
S Accumulator spring:
Spring
Free length
Outer
diameter
mm(in.)Color
B1(O/D & 2nd
brake)47.13(1.8555)/
16.0(0.630)Pink
C1(Forward
clutch)57.90(2.2795)/
17.2(0.677)–
C2(Direct
clutch)57.20(2.2520)/
17.5(0.689)Green
111. Coat a new apply gasket with ATF, install it to
the transaxle case.
112. Coat a new brake drum gasket with ATF, install
it to the transaxle case.
113. Install the spring and check valve.