2004 DAEWOO LACETTI turn signal

9B – 2ILIGHTING SYSTEMS
DAEWOO V–121 BL4
SPECIFICATIONS
BULB USAGE CHART
BulbReplacement Bulb Number
Backup Lamp21W
Center High–Mounted Stoplamp5W
Front Fog Lamp27W
Headlamp55W
Interior Courtesy Lamp10W
License Plate Lamp5W
Luggage Compartment Lamp10W
Park and Front Turn Signal LampDouble 21/5W
Rear Fog Lamp21W
Rear Turn Signal Lamp21W
Side Turn Signal Lamp5W
Taillamp and StoplampDouble 21/5W
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNSmLb–FtLb–In
CHMSL Mounting Nuts4–35
Door Jamb Switch Screw4–35
Front Fog Lamp Nuts4–35
Headlamp Assembly Bolts and Nuts4–35
License Plate Lamp Screws4–35
Map Lamp Screws1.5–13
Rear Combination Lamp Assembly Screws4–35
Hatchback Extension Lamp3–27

9B – 28ILIGHTING SYSTEMS
DAEWOO V–121 BL4
Turn Signal Lamps and Hazard Lamps Do Not Work
StepActionValue(s)YesNo
1Check fuses F3 and F14.
Is either fuse blown?–Go to Step 2Go to Step 3
21. Check for a short circuit and repair it, if neces-
sary.
2. Replace the fuse.
Is the repair complete?–System OK–
31. Turn the ignition ON.
2. Check the voltage at fuses F3 and F14.
Does the battery voltage available at both fuses F3
and F14 equal the specified value?11–14 vGo to Step 4Go to Step 7
41. Turn the hazard switch on.
2. Remove each of the inoperative lamps from its
socket.
3. Test each lamp socket positive terminal with a
voltmeter.
Does the battery voltage pulsing at the turn signal
hazard lamp socket positive terminal equal the spe-
cified value?11–14 vGo to Step 5Go to Step 9
5At each bulb socket, use an ohmmeter to check the
ground circuit.
Is the resistance equal to the specified value?
0 WGo to Step 6Go to Step 8
6Replace any faulty turn signal/hazard bulbs.
Is the repair complete?–System OK–
7Repair the power supply circuit to fuses.
Is the repair complete?–System OK–
8Repair the open ground wires.
Is the repair complete?–System OK–
91. Turn on the hazard lamp switch.
2. Test the blinker unit connector terminal 49a
with a voltmeter.
Does the battery voltage pulsing at the blinker unit
terminal 49a equal the specified value?11–14 vGo to Step 15Go to Step 10
101. Turn on the hazard lamp switch.
2. Test the blinker unit connector terminal 49 with
a voltmeter.
Does the battery voltage available at the blinker unit
terminal 49 equal the specified value?11–14 vGo to Step 11Go to Step 14
111. Disconnect the blinker unit from the connector.
2. Use an ohmmeter to check between ground
and the connector for terminal 31 of the blinker
unit.
Is the resistance equal to the specified value?
0 WGo to Step 13Go to Step 12
12Repair the blinker unit ground connection.
Is the repair complete?–System OK–
13Replace the faulty blinker unit.
Is the repair complete?–System OK–

9B – 30ILIGHTING SYSTEMS
DAEWOO V–121 BL4
Hazard Lamps Do Not Operate, Turn Signals Are OK
StepActionValue(s)YesNo
1Check fuse F14.
Is fuse F14 blown?–Go to Step 2Go to Step 3
21. Check for a short circuit and repair it, if neces-
sary.
2. Replace the fuse.
Is the repair complete?–System OK–
3Use a voltmeter to check for power to fuse F14.
Does the battery voltage available at fuse F14 equal
the value specified?11–14 vGo to Step 5Go to Step 4
4Repair the power supply circuit to fuse F14.
Is the repair complete?–System OK–
51. Disconnect the hazard switch connector.
2. Use a voltmeter to check power to the hazard
switch terminal 8.
Does the battery voltage available at connector ter-
minal 8 equal the value specified?11–14 vGo to Step 6Go to Step 9
61. Remove the hazard switch and disconnect it
for testing.
2. Turn the hazard switch on.
3. Test with an ohmmeter between terminals 7
and 8.
Is the resistance equal to the specified value?0 WGo to Step 7Go to Step 10
71. With the hazard switch still removed and dis-
connected for testing, turn the hazard switch
on.
2. Use an ohmmeter to check between terminals
5, 6, and 9.
Is the resistance equal to the specified value?0 WGo to Step 8Go to Step 10
8Repair the open circuit between the hazard lamp
switch connector and splice S202.
Is the repair complete?–System OK–
9Repair the open circuit between the hazard switch
connector terminal 8 and fuse F14.
Is the repair complete?–System OK–
10Replace the faulty hazard switch.
Is the repair complete?–System OK–

9B – 36ILITHING SYSTEMS
DAEWOO V–121 BL4
MAINTENANCE AND REPAIR
ON–VEHICLE SERVICE
HEADLAMPS/FRONT TURN SIGNAL
LAMPS
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the headlamp mounting bolts and nut.
3. Disconnect the electrical connectors.
4. Remove the turn signal bulb.
5. Remove the headlamp assembly.
6. Remove the cap concealing the headlamp bulb.
7. Disconnect the headlamp bulb electrical connector.
8. Remove the headlamp bulb.
Installation Procedure
1. Install the headlamp bulb.
2. Connect the headlamp bulb electrical connector.
3. Install the cap concealing the headlamp bulb.
4. Install the turn signal bulb.
5. Connect the electrical connectors.
Notice : Dissimilar metals in direct contact with each other
may corrode rapidly. Make sure to use the correct fasten-
ers to prevent premature corrosion.
6. Install the headlamp assembly with the bolts and
nut.
7. Connect the negative battery cable.

9B – 38ILITHING SYSTEMS
DAEWOO V–121 BL4
Installation Procedure
1. Install the parking lamp.
2. Install the headlamp. Refer to ”Headlamps” in this
section.
3. Connect the negative battery cable.
SIDE TURN SIGNAL LAMPS
Removal Procedure
1. Disconnect the negative battery cable.
2. Slide the side turn signal lamp rearward.
3. Remove the lamp.
4. Disconnect the electrical connector.
Installation Procedure
1. Connect the electrical connector.
2. Install the side turn signal lamp.
3. Connect the negative battery cable.
FRONT FOG LAMPS
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the bolts and the front fog lamp.
3. Disconnect the electrical connector.

9B – 46ILITHING SYSTEMS
DAEWOO V–121 BL4
GENERAL DESCRIPTION
AND SYSTEM OPERATION
HEADLAMPS–ON REMINDER CHIME
When the headlamp switch is in the headlamps–on or
parking lamps–on position, voltage is applied to the chime
module. When the ignition is in ON, ACC or START, volt-
age is applied through the fuse block to the module. These
two voltages are sensed, and the chime module is not
sounded.
When the ignition is not in ON, ACC or START, the module
loses voltage. The chime module senses change. If the
voltage is still available, it is applied to sound the chime.
The chime can be turned off by turning the headlamp
switch off. The module no longer senses voltage from the
headlamp switch, so the chime module does not sound.
HEADLAMPS
The headlamps are controlled by the multifunction lever
located on the left side of the steering column. They will
come on with the ignition switch in any position. Turning
the headlamp switch to the first position turns on the park-
ing lamps, the license plate lamps and the instrument pan-
el illumination. Turning the switch to the second position
turns on all of the previous lamps and the headlamps.
Turning the switch to the OFF position turns off all the
lamps.
Headlamp high beams and low beams are also controlled
by this lever. When the headlamps are on, pushing the le-
ver away from the driver until the switch clicks changes the
lamp from low beam to high beam. An indicator lamp on
the instrument cluster assembly will come on when the
high beam headlamps are on. To return the headlamps to
low beam, pull the lever toward the driver.
The headlamps must be aimed for proper illumination of
the road. Headlamp aim should be checked whenever a
new headlamp assembly is installed, or whenever service
repairs to the front end area may have disturbed the head-
lamp assembly or its mountings.
DAYTIME RUNNING LAMPS
The Daytime Running Lamps (DRL) will come on when:
S The ignition is ON.
S The light is OFF.
S The parking brake is released.
When the exterior lights are on, the DRL will turn off. To
turn the DRL off when idling, apply the parking brake.
PARKING AND TURN SIGNAL LAMPS
The parking lamps can be turned on by turning the lighting
switch to the first position. The parking lamps can be
turned off by turning the switch to the OFF position.When the turn signals are activated, the front and rear turn
signal lamps flash to signal a turn. The turn signals work
only when the ignition is ON.
The turn signals are controlled by the light switch on the
left side of the steering column. Moving the lever all the
way up or down (past the detent) will turn on the front and
rear turn signals. When the turn is completed, the lever will
return to horizontal and the turn signals will stop flashing.
For changing lanes, or for shallow turns in which the steer-
ing wheel does not turn far enough to cancel the signal,
move the signal lever only to the first detent and hold it
there. When the lever is released, it will return to horizontal
and the turn signals will cancel.
FOG LAMPS
The fog lamp switch is on the instrument panel to the right
of the steering column. To use the fog lamps, first turn on
the headlamps or the parking lamps. Then push the fog
lamp switch. The indicator light in the switch will illuminate
to indicate that the fog lamps are on. Push the switch again
to turn off the fog lamps. The indicator light will then go off.
The fog lamps should not be used as a substitute for the
headlamps.
The fog lamps must be aimed for proper illumination of the
road. Fog lamp aim should be checked when a new bulb
is installed or if service or repairs in the front end area may
have disturbed the fog lamp mountings.
REAR COMBINATION LAMPS
The taillamps, stoplamps, turn signal lamps and backup
lamp are one assembly.
Turning on either the headlamps or the parking lamps will
also turn on the taillamps. When the brake pedal is
pushed, the taillamps will glow brighter to serve as sto-
plamps.
The center high–mounted stoplamp is located in the rear
window and will come on when the brake pedal is pressed.
LICENSE PLATE LAMP
The license plate lamps will come on when the headlamps
or the parking lamps are on. The license plate lamps are
mounted above the license plate.
INTERIOR COURTESY LAMP
The courtesy lamp is located on the headliner just behind
the front seats. The lamp switch has three positions. If the
switch is left in the center position, the lamp will go on
whenever a door is opened and go off when it is closed.
In the ON position, the lamp will stay on until it is turned off.
In the OFF position, the lamp will not come on, even when
a door is opened.
LUGGAGE COMPARTMENT LAMP
The luggage compartment lamp is located under the deck
lid sill plate on the notchback. The lamp is located on the
left–side wheelhouse trim panel on the hatchback. It will
come on whenever the luggage compartment is opened.

9E – 2IINSTRUMENTATION/DRIVER INFORMATION
DAEWOO V–121 BL4
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNSmLb–FtLb–In
Air Deflector Screws2–18
Chime Module Screws4–35
Clock Screws2–18
Cupholder Screws2.5–22
Deposit Box Screws2.5–22
Driver Knee Bolster Bolts10–89
Floor Console Brace Bolts4–35
Floor Console Brace Nuts4–35
HVAC Controls Screws4–35
Instrument Cluster Screws4–35
Instrument Cluster Trim Panel Screws4–35
Instrument Panel End Bolts2015–
Instrument Panel End Screws4–35
Instrument Panel Nuts Above the Steering Column2015–
Instrument Panel Bolts Behind the HVAC Controls4–35
Steering Column Bracket Nut2216–
Steering Column Lower Trim Cover Screws2.5–22
Steering Column U–Clamp Nuts2216–
Steering Column Upper Trim Cover Screws3–27
INSTRUMENT CLUSTER INDICATOR LAMPS
SPECIFICATIONS
Indicator LampColorBulb
ABS WarningAmber14 v 1.4 W
Airbag WarningRed14 v 1.4 W
Battery Charge IndicatorRed14 v 1.4 W
Check EngineAmber14 v 1.4 W
Door Open WarningRed14 v 1.4 W
Engine OverheatRed14 v 1.4 W
Fasten Seat Belt WarningRed14 v 1.4 W
High Beam IndicatorBlue14 v 1.4 W
Low Fuel Level WarningAmber14 v 4 W
Oil Pressure WarningRed14 v 1.4 W
Parking Brake Indicator and Brake Fluid WarningRed14 v 1.4 W
Service Engine Soon WarningAmber14 v 1.4 W
Transaxle Power Mode IndicatorAmber14 v 1.4 W
Turn Signal IndicatorsGreen14 v 1.4 W

9T1 – 4IREMOTE KEYLESS ENTRY AND ANTI–THEFT SYSTEM
DAEWOO V–121 BL4
CONTROL MODULE/RECEIVER CONNECTOR
TerminalColorDescription
1YELSiren
2BLKGround
3––
4LT BLUDoor and Trunk Tamper Switch
5PNK/BLKTrunk Open Switch
6––
7PNK/DKBLUHood Open Switch
8PPLDoor contact Switch
9LT BLU/BLKUnlock
10LT GRN/WHTLock
11YELUnlock
12LT GRNAnti–Theft Door Locking Switch
13DK BLURight Turn Signal Bulb
14––
15PNKIgnition+
16––
17LT GRNDiagnostic Communication
18LT GRN/REDKey Reminder Switch
19YEL/DK GRNSecurity Indicator
20PPLAnti–Theft Door Locking Switch
21––
22––
23––
24BRNTrunk Open Switch
25ORNBattery+
26LT BLULeft Turn Signal Bulb