2004 DAEWOO LACETTI differential

AISIN AUTOMATIC TRANSAXLE 5A2 – 23
DAEWOO V–121 BL4
1. Side Bearing Outer Race
2. Differential Case
3. Shim
4. Outer Tapered Roller Bearing Race
5. Counter Driven Gear
6. Oil Seal
7. Oil Pump8. Thrust Needle Roller Bearing
9. Direct Clutch Assembly
10. Thrust Bearing Race
11. Direct Clutch Hub
12. Counter Driven Gear
13. Transaxle Case Plate
14. Apply Gasket

AISIN AUTOMATIC TRANSAXLE 5A2 – 123
DAEWOO V–121 BL4
36. Remove the 16 bolts and tap on the circumference
of the transaxle housing with a plastic hammer to
remove the transaxle housing from the transaxle
case.
Important : Be careful not to drop the differential gear as-
sembly when the transaxle housing is removed.
37. Using a dial indicator, measure the input shaft end
play.
S End play : 0.3
0.9 mm (0.012–0.035 in.)
38. Remove the 6 bolts and oil pump.
39. Remove the differential gear assembly from the
transaxle case.

AISIN AUTOMATIC TRANSAXLE 5A2 – 137
DAEWOO V–121 BL4
MAJOR COMPONENT ASSEMBLY
Tools Required
DW240–020 Brake/Clutch Spring Compressor
DW240–050 Overdrive Brake Adapter
DW240–060–01 Brake Spring Compressor Bolt/Nut
DW240–060–02 Brake Spring Compressor Plate
DW240–070 1st / Reverse Brake Adapter
DW240–100 Counter Drive Gear Installation Adapter
DW240–130 Differential Preload Adapter
DW260–031–01 Transaxle Housing Oil Seal Installer
DW260–031–02 Transaxle Case Oil Seal Installer
DW260–041 Planetary Ring Gear Nut Removal/Installa-
tion Socket
DW240–160 Transaxle Case Outer Tapered Roller Bear-
ing Race Adapter
DW240–140 Transaxle Housing Side Bearing Outer Race
Adapter
DW240–170 Adapter Handle
Assembly Procedure
1. Install 4 new O–rings to the 4 screw plugs.
2. Install the 4 screw plugs with the O–rings to the
transaxle rear cover.
Tighten
Tighten the screw plugs to 7.4 NSm (65 lb–in).
3. Install the 2 seal rings to the transaxle rear cover.
4. Using the vernier calipers, measure the free length
of the O/D brake piston return spring together with
the spring seat.
S Standard free length : 18.99 mm (0.7476 in.)

AISIN AUTOMATIC TRANSAXLE 5A2 – 139
DAEWOO V–121 BL4
9. Using transaxle housing oil seal installer
DW260–031–01 and a hammer, drive in a new
transaxle housing oil seal.
S Oil seal in depth: 3.1mm (0.122 in.)
10. Install a new outer tapered roller bearing race into
the transaxle housing.
Notice : Press
fit the outer tapered roller bearing race un-
til it contacts the transaxle housing.
11. Install the transaxle lube apply pipe and differential
gear lube apply pipe to the transaxle housing.
12. Install the No.1 transaxle apply pipe clamp to the
transaxle housing with the bolt.
Tighten
Tighten the bolt to 5.4 NSm (48 lb–in).
13. Install the oil reservoir lock plate to the transaxle
housing with the 3 bolts.
Tighten
Tighten the bolts to 5.4 NSm (48 lb–in).

AISIN AUTOMATIC TRANSAXLE 5A2 – 141
DAEWOO V–121 BL4
20. Install the differential gear to the transaxle case.
21. Install the transaxle housing and tighten the 16
bolts of the transaxle housing temporarily.
22. Tighten 8 or 9 bolts out of 16 bolts of the transaxle
housing completely.
Tighten
Tighten the bolt to 29 NSm (22 lb–ft).
23. Using differential preload adapter DW240–130, turn
the differential gear assembly right and left 2 or 3
times to allow the bearing settle.
24. Using differential preload adapter DW240–130 and
small torque wrench, measure the preload of the
differential gear.
Notice : Note down the measured valve.

5A2 – 142IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
25. Remove the transaxle housing and install the
counter driven gear.
26. Install the transaxle housing and tighten the 16
bolts of the transaxle housing temporarily.
27. Tighten the bolts of the transaxle housing in the
same manner as in step 22.
Tighten
Tighten the bolts to 29 NSm (22 lb–in).
28. Using differential preload adapter DW240–130, turn
the differential gear assembly right and left 2 or 3
times to allow the bearing settle.
29. Using differential preload adapter DW240–130 and
a small torque wrench, measure the preload of the
differential gear. From this valve deduct the valve
measured in step 23. This is the preload of the
counter driven gear.
S Preload:
New bearing: 0.33–0.76 NSm (3.21–6.77 lb–in)
Used bearing: 0.17–0.38 NSm (1.48–3.39 lb–in)

AISIN AUTOMATIC TRANSAXLE 5A2 – 157
DAEWOO V–121 BL4
91. Apply formed in place gasket (FIPG) to the trans-
axle rear cover.
FIPG: three bond 1281 or equivalent
Seal bend width: 1.2 mm (0.047 in.)
92. Install the transaxle rear cover to the transaxle case
with the 9 bolts.
Tighten
Tighten the bolts to 25 NSm (18 lb–ft).
93. Install the counter driven gear assembly to the
transaxle case.
94. Install the differential gear assembly to the trans-
axle case.

5A2 – 208IAISIN AUTOMATIC TRANSAXLE
DAEWOO V–121 BL4
DIFFERENTIAL CASE
1. Differential Pinion Thrust Washer
2. Differential Pinion Gear
3. Differential Side Gear Thrust Washer
4. Differential Side Gear
5. Pin
6. Differential Pinion Shaft
7. Oil Seal
8. Side Bearing Outer Race9. Tapered Roller Bearing
10. Differential Case
11. Differential Ring Gear
12. Tapered Roller Bearing
13. Side Bearing Outer Race
14. Shim
15. Oil Seal