2004 DAEWOO LACETTI Section 6

ENGINE CONTROLS 1F – 471
DAEWOO V–121 BL4
The EGR Decel Filter value should always be at –3 or low-
er. If the EGR Decel Filter number becomes more positive
(towards 0 or more), then the EGR system is becoming re-
stricted. Look for possible damage to the EGR pipe or for
a restriction caused by carbon deposits in the EGR pas-
sages or on the EGR valve.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. Commanding the EGR valve open determines
whether the EGR system can control the EGR
valve accurately and if the fault is present. The dif-
ference between the current and commanded posi-
tion is greater than 15%.
3. When the EGR valve electrical connector is discon-
nected, the scan tool should display the Actual
EGR Position as 0%. If it does not, the fault lies
either in the EGR signal circuit or the ECM.
4. There may be a slight delay for the voltage dis-
played on the DVM to change after the scan tool
commands the EGR valve to operate.
5. An open or poor connection condition may have
caused this DTC to set. Be sure to check the termi-
nals for being backed out, improperly formed or
damaged, and for poor tension.
7. The test light will have glowed brightly in the pre-
vious step if the EGR control circuit was shorted to
B+ and the Actual EGR Position on the scan toolwill display 100%. A test light that did not illuminate,
indicates that the circuit may be open or shorted to
ground.
9. If the EGR valve 5 volt reference is shorted to volt-
age, the digital voltmeter (DVM) will read battery
voltage and additional DTCs may be set and the
engine performance will be poor.
12. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
13. Although the circuitry acted correctly when
checked, a problem may still lie within the terminals
which would not show up in probe type testing. Be
sure to check the terminals for being backed out,
improperly formed or damaged, and for poor ten-
sion.
17. All circuits to the EGR valve are OK at this point.
The fault lies internally in the EGR valve and, there-
fore, must be replaced. Be sure all gasket material
is removed from the EGR mounting surface. Even
a small amount of material may cause a DTC
P0401 to set.
18. Check the terminals for being backed out, improp-
erly formed or damaged, and for poor tension.
19. Clearing DTCs is a very important step for this
diagnostic. The clearing function allows the EGR
valve to relearn a new pintle position as the old
pintle position was inaccurate due to the failure that
caused the DTC. The DTC must be cleared with
the ignition ON, engine OFF or when the engine is
idling. If the ECM sees a EGR command, the new
pintle will not be learned.
20. If no malfunctions have been found at this point and
no additional DTCs were set, refer to ”Diagnostic
Aids” in this section for additional checks and infor-
mation.
DTC P0402 – Exhaust Gas Recirculation Excessive Flow
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data link Connector
(DLC).
2. Turn the ignition ON.
3. Command the Exhaust Gas Recirculation
(EGR) valve to the specific values.
Does the Actual EGR Position follow the Desired
EGR Position?25%, 50%,
75%, 100%Go to Step 19Go to Step 3
31. Turn the ignition OFF.
2. Disconnect the EGR valve.
3. Turn the ignition ON.
4. With a test light connected to B+, probe the
EGR valve wiring harness connector terminal
2.
Does the test light illuminate?–Go to Step 4Go to Step 5

ENGINE CONTROLS 1F – 475
DAEWOO V–121 BL4
the Actual EGR and Desired EGR Positions on a cold ve-
hicle with a scan tool, the fault can be easily verified.
Check the freeze frame data to determine if the DTC set
when the vehicle was cold by viewing the Engine Coolant
Temperature (ECT).
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. Commanding the EGR valve open determines
whether the EGR system can control the EGR
valve accurately and if the fault is present. The dif-
ference between the current and commanded posi-
tion is greater than 15%.
3. When the EGR valve electrical connector is discon-
nected, the scan tool should display the Actual
EGR Position as 0%. If it does not, the fault lies
either in the EGR signal circuit or the ECM.
4. There may be a slight delay for the voltage dis-
played on the DVM to change after the scan tool
commands the EGR valve to operate.
5. An open or poor connection condition may have
caused this DTC to set. Be sure to check the termi-
nals for being backed out, improperly formed or
damaged, and for poor tension.
7. The test light will have glowed brightly in the pre-
vious step if the EGR control circuit was shorted to
B+ and the Actual EGR Position on the scan toolwill display 100%. A test light that did not illuminate,
indicates that the circuit may be open or shorted to
ground.
9. If the EGR valve 5 volt reference is shorted to volt-
age, the digital voltmeter (DVM) will read battery
voltage and additional DTCs may be set and the
engine performance will be poor.
12. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
13. Although the circuitry acted correctly when
checked, a problem may still lie within the terminals
which would not show up in probe type testing. Be
sure to check the terminals for being backed out,
improperly formed or damaged, and for poor ten-
sion.
17. All circuits to the EGR valve are OK at this point.
The fault lies internally in the EGR valve and, there-
fore, must be replaced. Be sure all gasket material
is removed from the EGR mounting surface. Even
a small amount of material may cause a DTC
P0401 to set.
18. Check the terminals for being backed out, improp-
erly formed or damaged, and for poor tension.
19. Clearing DTCs is a very important step for this
diagnostic. The clearing function allows the EGR
valve to relearn a new pintle position as the old
pintle position was inaccurate due to the failure that
caused the DTC. The DTC must be cleared with
the ignition ON, engine OFF or when the engine is
idling. If the ECM sees a EGR command, the new
pintle will not be learned.
20. If no malfunctions have been found at this point and
no additional DTCs were set, refer to ”Diagnostic
Aids” in this section for additional checks and infor-
mation.
DTC P0404 – Exhaust Gas Recirculation Open Valve Position Error
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
3. Command the Exhaust Gas Recirculation
(EGR) valve to the specific values.
Does the Actual EGR Position follow the Desired
EGR Position?25%, 50%,
75%, 100%Go to Step 19Go to Step 3
31. Turn the ignition OFF.
2. Disconnect the EGR valve.
3. Turn the ignition ON.
4. With a test light connected to B+, probe the
EGR valve wiring harness connector terminal
2.
Does the test light illuminate?–Go to Step 4Go to Step 5

ENGINE CONTROLS 1F – 479
DAEWOO V–121 BL4
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. Commanding the EGR valve open determines
whether the EGR system can control the EGR
valve accurately and if the fault is present.
3. If the EGR valve 5 volt reference is shorted to
ground, the digital voltmeter (DVM) will read no
voltage and additional DTCs may be set and the
engine performance will be poor. When this circuit
is open, only a DTC P0405 will be set.
4. Jumpering the 5 volt reference circuit to the signal
circuit checks the signal circuit and the ECM. The
scan tool should display the Actual EGR Position
as 100% if the signal circuit and ECM are OK.
6. Although the ECM and circuitry acted correctly in
the previous step, a problem may still lie within the
terminals which would not show up in probe typetesting. Be sure to check the terminals for being
backed out, improperly formed or damaged, and for
poor tension.
10. All circuits to the EGR valve are OK at this point.
The fault lies internally in the EGR valve and there-
fore must be replaced. Be sure all gasket material
is removed from the EGR mounting surface. Even
a small amount of material may cause a DTC
P0401 to set.
13. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
14. Check the terminals for being backed out, improp-
erly formed or damaged, and for poor tension.
15. Clearing DTCs is a very important step for this
diagnostic. The clearing function allows the EGR
valve to relearn a new pintle position as the old
pintle position was inaccurate due to the failure that
caused the DTC. The DTC must be cleared with
the ignition ON, engine OFF or when the engine is
idling. If the ECM sees an EGR command, the new
pintle will not be learned.
16. If no malfunctions have been found at this point and
no additional DTCs were set, refer to ”Diagnostic
Aids” in this section for additional checks and infor-
mation.
DTC P0405 – Exhaust Gas Recirculation Pintle Position Low
Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
3. Command the Exhaust Gas Recirculation
(EGR) valve to the specific values.
Does the Actual EGR Position follow the Desired
EGR Position?25%, 50%,
75%, 100%Go to Step 15Go to Step 3
31. Turn the ignition OFF.
2. Disconnect the EGR valve.
3. Turn the ignition ON.
4. With a voltmeter connected to the ground,
probe the 5 volt reference circuit at terminal 4
of the EGR valve wiring harness connector.
Is the voltage near the specified value?5 VGo to Step 4Go to Step 5
4Jumper the 5 volt reference circuit to the signal cir-
cuit at terminal 4 and C at the EGR valve wiring har-
ness connector.
Does the Actual EGR Position display the specific
value?100%Go to Step 6Go to Step 7

1F – 482IENGINE CONTROLS
DAEWOO V–121 BL4
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. Commanding the EGR valve open determines
whether the EGR system can control the EGR
valve accurately and if the fault is present.
3. If the EGR valve 5 volt reference is shorted to
ground, the digital voltmeter (DVM) will read no
voltage and additional DTCs may be set and the
engine performance will be poor. When this circuit
is open, only a DTC P0405 will be set.
4. Jumpering the 5 volt reference circuit to the signal
circuit checks the signal circuit and the ECM. The
scan tool should display the Actual EGR Position
as 100% if the signal circuit and ECM are OK.
6. Although the ECM and circuitry acted correctly in
the previous step, a problem may still lie within the
terminals which would not show up in probe typetesting. Be sure to check the terminals for being
backed out, improperly formed or damaged, and for
poor tension.
10. All circuits to the EGR valve are OK at this point.
The fault lies internally in the EGR valve and, there-
fore, must be replaced. Be sure all gasket material
is removed from the EGR mounting surface. Even
a small amount of material may cause a DTC
P0401 to set.
12. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
13. Check the terminals for being backed out, improp-
erly formed or damaged, and for poor tension.
14. Clearing DTCs is a very important step for this
diagnostic. The clearing function allows the EGR
valve to relearn a new pintle position as the old
pintle position was inaccurate due to the failure that
caused the DTC. The DTC must be cleared with
the ignition ON, engine OFF or when the engine is
idling. If the ECM sees an EGR command, the new
pintle will not be learned.
15. no malfunctions have been found at this point and
no additional DTCs were set, refer to ”Diagnostic
Aids” in this section for additional checks and infor-
mation.
DTC P0406 – Exhaust Gas Recirculation Pintle Position High
Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Install a scan tool to the Data Link Connector
(DLC).
3. Command the Exhaust Gas Recirculation
(EGR) valve to the specific values.
Does the Actual EGR Position follow the Desired
EGR Position?25%, 50%,
75%, 100%Go to Step 14Go to Step 3
31. Turn the ignition OFF.
2. Disconnect the EGR valve.
3. Turn the ignition ON.
4. With a voltmeter connected to the ground,
probe the 5 volt reference circuit at terminal 4
of the EGR valve wiring harness connector.
Is the voltage near the specified value?5 VGo to Step 4Go to Step 5
4Jumper the 5 volt reference circuit to the signal cir-
cuit at terminal 4 and C at the EGR valve wiring har-
ness connector.
Does the Actual EGR Position display the specific
value?100%Go to Step 6Go to Step 7

ENGINE CONTROLS 1F – 485
DAEWOO V–121 BL4
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. If any component DTCs are set, diagnose those
DTCs first. A fault in a component can cause the
converter to appear degraded or may have caused
its failure.
3. This step includes checks for conditions that can
cause the three–way catalytic converter to appear
degraded. Repair any problems found before pro-
ceeding with this table.
5. If the three–way catalytic converter needs to be
replaced, make sure that another condition is not
present which would cause the converter to be-
come damaged. These conditions may include thefollowing: misfire, high engine oil or coolant con-
sumption, and/or retarded spark timing or weak
spark. To avoid damaging the replacement convert-
er, correct any possible causes of converter dam-
age before replacing the catalytic converter.
6. Clearing DTCs allows the catalyst test to be run up
to 6 times this ignition cycle. Once the ignition is
cycled, the test will run only once. Driving the ve-
hicle heats the catalyst to a test temperature. The
ECM must see predetermined amount of time at
above idle before allowing the catalyst test to run at
idle. Once at idle, the ECM will allow the system to
stabilize and then test the catalyst in 2 stages.
7. If no faults have been found at this point and no
additional DTCs were set, refer to ”Diagnostic Aids”
in this section for additional checks and informa-
tion.
DTC P0420 – Catalyst Oxygen Sensor Low Efficiency
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2S Install a scan tool to the Data Link Connector
(DLC).
S Turn the ignition ON.
Are any component Diagnostic Trouble Codes
(DTCs) set?–Go to
applicable DTC
tablesGo to Step 3
3Visually/physically check the following:
S Exhaust system for a leak.
S Rear Heated Oxygen Sensor (HO2S2)
Is a problem found?–Go to Step 4Go to Step 5
4Repair the exhaust system as needed.
Is the repair complete?–Go to Step 6–
5Replace the Three Way Catalytic Converter (TWC).
Is the repair complete?–Go to Step 6–
61. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the Conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 7Go to Step 2
7Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

ENGINE CONTROLS 1F – 493
DAEWOO V–121 BL4
DTC P0462 – Fuel Level Low Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Start the engine and operate the vehicle within
Failure Record condition as noted.
Is Diagnostic trouble Codes (DTCs) P0462 set?–Go to Step 3Go to
”Diagnostic
Aids”
31. Turn the ignition OFF.
2. Disconnect the fuel pump connector.
3. Turn the ignition ON.
4. Using a voltmeter, measure the fuel level signal
voltage at the fuel level sensor connector ter-
minal 1.
Is the voltage within the specified value?0.4 – 4.5 VGo to Step 4Go to Step 6
4Check for a proper ground connection at the fuel
tank and repair as needed.
Is the repair complete?–Go to Step 11Go to Step 5
51. Remove the fuel pump from the fuel tank.
2. Reconnect the fuel pump connector.
3. Turn the ignition ON.
4. Monitor the fuel level sensor parameter on the
scan tool while moving the fuel sensor float
from empty position to full position.
5. Repeat procedure 4 several times.
Does the fuel level sensor vale on the scan tool in-
crease and then decrease steadily when the float is
moved?–Go to
”Diagnostic
Aids”Go to Step 8
6Check for an open or short to ground in the fuel level
sensor circuit and repair as needed.
Is the repair necessary?–Go to Step 11Go to Step 9
7Repair the open or short to ground in the fuel level
sensor circuit between the fuel level sensor harness
connector and fuel level sensor.
Is the repair complete?–Go to Step 11–
81. Turn the ignition OFF.
2. Replace the fuel pump assembly.
Is the repair complete?–Go to Step 11–
91. Turn the ignition OFF.
2. Connect the fuel pump connector.
3. Disconnect the engine Control Module (ECM)
connector.
4. Turn the ignition ON.
5. Using a digital voltmeter, measure the voltage
in the signal circuit at terminal K51.
Is the voltage within the specified value?4–5 VGo to Step 10Go to
Section 9E, In-
strumentation/
Driver Informa-
tion
10S Turn the ignition OFF.
S Replace the ECM.
Is the repair complete?–Go to Step 11–

1F – 496IENGINE CONTROLS
DAEWOO V–121 BL4
DTC P0463 – Fuel Level High Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Start the engine and operate the vehicle within
Failure Record condition as noted.
Is Diagnostic trouble Codes (DTCs) P0463 set?–Go to Step 3Go to
”Diagnostic
Aids”
31. Turn the ignition OFF.
2. Disconnect the fuel pump connector.
3. Turn the ignition ON.
4. Using a voltmeter, measure the fuel level signal
voltage at the fuel level sensor connector ter-
minal 1.
Is the voltage within the specified value?0.4 – 4.5 VGo to Step 4Go to Step 6
4Check for a proper ground connection at the fuel
tank and repair as needed.
Is the repair necessary?–Go to Step 11Go to Step 5
51. Remove the fuel pump from the fuel tank.
2. Reconnect the fuel pump connector.
3. Turn the ignition ON.
4. Monitor the fuel level sensor parameter on the
scan tool while moving the fuel sensor float
from empty position to full position.
5. Repeat procedure 4 several times.
Does the fuel level sensor vale on the scan tool in-
crease and then decrease steadily when the float is
moved?–Go to
”Diagnostic
Aids”Go to Step 8
6Check for short to voltage in the fuel level sensor cir-
cuit and repair as needed.
Is the repair necessary?–Go to Step 7Go to Step 9
7Repair the short to voltage in the fuel level sensor cir-
cuit between the fuel level sensor harness connector
and fuel level sensor.
Is the repair necessary?–Go to Step 11–
8S Turn the ignition OFF.
S Replace the fuel pump assembly.
Is the repair complete? –Go to Step 11–
91. Turn the ignition OFF.
2. Connect the fuel pump connector.
3. Disconnect the engine Control Module (ECM )
connector.
4. Turn the ignition ON.
5. Using a digital voltmeter, measure the voltage
in the signal circuit at terminal K51.
Is the voltage within the specified value?0.4 – 4.5 VGo to Step 10Go to
Section 9E, In-
strumentation/
Driver Informa-
tion
10S Turn the ignition OFF.
S Replace the ECM.
Is the repair complete?–Go to Step 11–

ENGINE CONTROLS 1F – 499
DAEWOO V–121 BL4
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
An intermittent problem may be caused by a poor connec-
tion, rubbed–through wire insulation, or a wire that is bro-
ken inside the insulation.
VSS signal circuit should be thoroughly checked for the
following conditions:
S Backed–out terminals
S Improper mating
S Broken locks
S Improperly formed
S Damaged terminals
S Poor terminal–to–wire connection
S Physical damage to the wiring harness
Ensure the VSS is correctly tightened with proper torque
to the transmission housing.
Refer to ”Intermittents”in this section.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. The permanent magnet generator only produces a
signal if the drive wheels are turning greater than 5
mph (8 km/h). This step determines if DTC P0502
is the result of a hard failure or an intermittent con-
dition.
3. Proper engine loads cannot be achieved in a shop
environment to properly run the vehicle within the
Freeze Frame Data conditions. It will be necessary
to drive the vehicle on the road to obtain the proper
engine loads.
4. This step verifies that the ECM is receiving a signal
from the vehicle speed sensor.
5. Refer to service bulletin information for the latest
calibration update.
6. Refer to the latest Techline information for program-
ming procedures.
8. A resistance reading that is higher than the speci-
fied value indicates that the VSS circuitry is open.
10. If the displayed resistance is less than the 1300
ohms, the VSS high and low circuits are shorted
together.
11. This checks the resistance of the VSS if no opens
or shorts were found on the VSS high and low cir-
cuits.
13. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
DTC P0502 – Vehicle Speed Sensor No Signal (Engine Side)
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
2Notice : Running the vehicle in gear with the wheels
hanging down at full travel will damage the drive
axles.
1. Install a scan tool to the Data Link Connector
(DLC).
2. Raise the drive wheels.
3. Support the lower control arms so that the
drive axles are in a horizontal (straight) posi-
tion.
4. Start the engine and allow to idle in gear.
Does the scan tool display vehicle speed above the
specific value?0 mphGo to Step 3Go to Step 4