2004 DAEWOO LACETTI jump start

1F – 252IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
41. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Using a DVM, measure the resistance between
terminals 85 and 9 in the relay control circuit in
the ECM harness connector to ground.
Does the DVM display infinite resistance?–Go to Step 12Go to Step 10
51. Turn the ignition switch to LOCK.
2. Disconnect the relay.
3. Connect a test light between the relay coil ter-
minals 86 and 85 in the relay harness connec-
tor.
4. Turn the Turn the ignition switch to ON.
5. Using the scan tool, command the relay ON
and OFF.
Does the test light turn ON and OFF with each com-
manded?–Go to Step 8Go to Step 6
6With the test light connected to ground, probe the
ignition feed circuit in the relay harness connector.
Does the test light illuminate?–Go to Step 7Go to Step 11
71. Turn the ignition switch to LOCK.
2. Reconnect the relay.
3. Disconnect the ECM connector containing the
relay control circuit.
4. Turn the Turn the ignition switch to ON.
5. With a fused jumper wire connected to ground,
probe the relay control circuit at terminal 9 in
the ECM harness connector.
Does the relay operate?–Go to Step 9Go to Step 10
8Check the connections at the relay.
Is a problem found and corrected?–Go to Step 14Go to Step 12
9Check the connection at the ECM.
Is a problem found and corrected?–Go to Step 11Go to Step 13
10Repair the faulty relay control circuit.
Is the repair complete?–Go to Step 14–
11Repair the faulty relay ignition feed circuit.
Is the repair complete?–Go to Step 14–
12Replace the relay.
Is the replacement complete?–Go to Step 14–
13Replace the ECM.
Is the replacement complete?–Go to Step 14–
141. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting the DTC as specifiec in the supporting
text.
Does the scan tool indicate that this diagnostic ran
and passed?–Go to Step 15Go to Step 2
15Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

1F – 350IENGINE CONTROLS
DAEWOO V–121 BL4
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. This step will determine if DTC P0107 is the result
of a hard failure or an intermittent condition.
3. Jumpering harness terminals 2 to 1 (signal circuit to
5 volts) will determine if the sensor is malfunction-
ing or if there is a problem with the ECM or wiring.6. The scan tool may not display 5 volts. The Impor-
tant thing is that the ECM recognizes the voltage as
more than 4 volts, indicating that the ECM and the
signal circuit are OK. A test light that illuminates
indicates a short to ground in the signal circuit.
7. A short to ground in the 5 volt reference circuit
could also set additional DTCs.
11. The replacement ECM must be programmed. Refer
to the latest Techline procedure for the ECM repro-
gramming.
DTC P0107 Manifold Absolute Pressure Low Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Start the engine.
3. Read the Manifold Absolute Pressure (MAP).
Does the scan tool display a MAP below the speci-
fied value?12 kPaGo to Step 3Go to Step 4
31. Turn the ignition switch OFF.
2. Disconnect the MAP sensor electrical connec-
tor.
3. Jumper the MAP signal circuit at terminal 2 to
the 5 volt reference circuit at terminal 1.
4. Turn the ignition switch ON.
Does the MAP read more than the specified value?96 kPaGo to Step 5Go to Step 6
41. Turn the ignition switch ON with the engine
OFF, review the Freeze Frame data, and note
the parameters.
2. Operate the vehicle within the freeze frame
conditions and Conditions For Setting the DTC
as noted.
Does the scan tool display MAP below the specified
value?12 kPaGo to Step 3Go to
”Diagnostic
Aids”
5Inspect the MAP sensor harness electrical connec-
tor terminals for the following conditions:
S Poor connections.
S Proper contact tension.
S Poor terminal to wire connection.
Is a problem found?–Go to Step 8Go to Step 9
61. Turn the ignition switch OFF.
2. Remove the jumper wire.
3. Probe the MAP sensor signal circuit terminal 2
with a test light to B+.
4. Turn the ignition switch ON.
Does the scan tool read over the specified value?90 kPaGo to Step 7Go to Step 12
7Check the MAP sensor 5 volt reference circuit at ter-
minal 1 for an open or short to ground.
Is a problem found?–Go to Step 10Go to Step 11

ENGINE CONTROLS 1F – 377
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
41. Turn the ignition OFF.
2. Disconnect HO2S1 connector.
3. Turn the ignition ON.
4. Jumper the Engine Control Module (ECM) side
HO2S1 signal circuit to ground.
Does the scan tool indicate the HO2S1 voltage be-
low the specified value?500 mVGo to
”Diagnostic
Aids”Go to Step 5
5Check the HO2S1 signal circuit, terminal 4 for a
short to voltage and repair as needed.
Is the repair complete?–Go to Step 7Go to Step 6
6S Turn the ignition OFF.
S Replace the ECM.
Is the repair complete?–Go to Step 7–
71. If disconnected, reconnect HO2S1 connector.
2. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
3. Start the engine and idle at normal operating
temperature.
4. Operate the vehicle within the Conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 8Go to Step 2
8Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to applica-
ble DTC tableSystem OK

ENGINE CONTROLS 1F – 383
DAEWOO V–121 BL4
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
S Normal scan tool voltage varies from 150 mV to
850 mV while in Closed Loop. If DTC P0134 is in-
termittent, refer to ”Intermittents” in this section.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. During engine warm–up, the HO2S1 should warm
up, and its voltage output should vary between 150
mv and 850 mv. When the HO2S1 voltage varies,
the engine will go into Closed Loop. This deter-
mines if the HO2S1 1 is operating properly.
4. This will determine if the sensor is malfunctioning or
if the wiring or the ECM is the cause of the DTC
P0134.
6. Use only a high impedance digital voltmeter (DVM)
for this test. The test checks the continuity of the
HO2S1 signal and the ground circuits; if the ground
circuit is open, the ECM voltage on the circuit will
be over 0.6 volts (600 mv).
10. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
DTC P0134 – Front Heated Oxygen Sensor (HO2S1)No Activity or
Open
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Start the engine and idle at normal operating
temperature.
3. Operate the engine above the specified rpm for
2 minutes.
Does the scan tool indicate Closed Loop?80°C(176°F)
1200 rpmGo to Step 3Go to Step 4
31. Review the Freeze Frame data and note the
parameters.
2. Operate the vehicle within the Freeze frame
conditions and Conditions For Setting the DTC
as noted.
Does the scan tool indicate CLOSED LOOP?–Go to Step 12Go to Step 4
41. Turn the ignition OFF.
2. Disconnect HO2S1 connector.
3. Jumper the terminal 3 of HO2S1 connector and
ground.
4. Turn the ignition ON.
Does the scan tool indicate the HO2S1 voltage with-
in the specified value?400 – 500 mVGo to Step 5Go to Step 8
5Check the HO2S1 harness connector for malfunc-
tion or poor connection and repair as needed.
Is the repair complete?–Go to Step 12Go to Step 6

1F – 384IENGINE CONTROLS
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
61. Idle the engine.
2. Remove the jumper wire.
3. Using a voltmeter, measure the voltage be-
tween terminal 4 of HO2S1 and ground
Is the voltage above the specified value?600 mVGo to Step 7Go to Step 11
71. Turn the engine OFF.
2. Using a voltmeter, measure the voltage be-
tween terminal 4 of the HO2S1 and ground.
Is the voltage below the specified value?300 mVGo to Step 9Go to Step 11
8Check the HO2S1 low circuit for an open or short to
ground between terminal 3 of the HO2S1 and termi-
nal M29 of the ECM and repair as needed.
Is the repair complete?–Go to Step 12Go to Step 10
9Check the HO2S1 signal circuit for an open or short
to ground between terminal 4 of the HO2S1 and ter-
minal M12 of the ECM and repair as needed.
Is the repair complete?–Go to Step 12Go to Step 10
10S Turn the ignition OFF.
S Replace the ECM.
Is the repair complete?–Go to Step 12–
11Replace the HO2S1.
Is the repair complete?–Go to Step 12–
121. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the Conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 13Go to Step 2
13Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
”Applicable
DTC table”System OK

ENGINE CONTROLS 1F – 389
DAEWOO V–121 BL4
S The ECM will record operating conditions at the
time the diagnostic fails. This information will be
stored in the Freeze Frame and Failure Records
buffers.
S A history DTC is stored.
Conditions for Clearing the MIL/DTC
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
An intermittent may be caused by rubbed–through wire in-
sulation or a wire contacting the exhaust.
Check for the following conditions:
S Exhaust system – Inspect the exhaust system for
leaks. Check the exhaust between the three–way
catalytic converter and the flange for leaks, corro-
sion, or for loose or missing hardware and repair as
necessary.
S Poor connection or damaged harness – Ensure that
the HO2S2 pigtail is not contacting the exhaust.
Check for the following conditions:
S Improper mating
S Broken locks
S Improperly formedS Damaged terminals
S Poor terminal–to–wire connection
S Damaged harness
S Intermittent test – Observe the HO2S2 on the scan
tool while moving related connections and the wir-
ing harness with the ignition ON. If the failure is in-
duced, the HO2S2 display will change. This may
help isolate the location of the malfunction.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. This step determines if DTC P0137 is the result of
a hard failure or an intermittent condition.
4. Jumping the HO2S2 low circuit, terminal 4 to
ground is necessary to allow the ECM to display
the supplied bias voltage. If the voltage is between
0.35 and 0.55 volt, then the wiring and ECM are
OK.
6. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
DTC P0137 – Rear Heated Oxygen Sensor (HO2S2) Low Voltage
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Turn the ignition ON.
Is the Rear Heated Oxygen Sensor (HO2S2) volt-
age less than the value specified?0.1 VGo to Step 4Go to Step 3
31. Start the engine.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze frame
conditions and Conditions For Setting the DTC
as noted.
Is the HO2S2 voltage less than the specified value?0.4 VGo to Step 4Go to Step 8
41. Turn the ignition OFF.
2. Disconnect HO2S2 connector.
3. Connect a jumper wire between terminal 1 of
HO2S2 connector and ground.
4. Turn the ignition ON.
Does the scan tool indicate that the HO2S2 voltage
is within the specified value?350–550 mVGo to Step 7Go to Step 5

ENGINE CONTROLS 1F – 393
DAEWOO V–121 BL4
StepNo Yes Value(s) Action
51. Reconnect the ECM connector.
2. Turn the ignition ON.
3. Jumper the high and low circuits at the HO2S2
connector, terminals 1 and 2 to ground.
Does the scan tool indicate the HO2S2 voltage be-
low the specified value?0.1 VGo to Step 7Go to Step 8
6Repair the short to voltage in the HO2S2 high circuit.
Is the repair complete?–Go to Step 9–
7S Turn the ignition OFF.
S Replace the HO2S2.
Is the repair complete?–Go to Step 9–
8S Turn the ignition OFF.
S Replace the ECM.
Is the repair complete?–Go to Step 9–
91. Using the scan tool, clear the Diagnostic
Trouble Codes (DTCs).
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the Conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?–Go to Step 10Go to Step 2
10Check if any additional DTCs are set.
Are any DTCs displayed that have not been diag-
nosed?–Go to
Applicable DTC
tableSystem OK

ENGINE CONTROLS 1F – 395
DAEWOO V–121 BL4
S The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.
S A history DTC will clear after 40 consecutive warm–
up cycles without a fault.
S The DTC(s) can be cleared by using the scan tool.
S Disconnecting the ECM battery feed for more than
10 seconds.
Diagnostic Aids
An intermittent may be caused by a rubbed–through wire
insulation or a wire contacting the exhaust.
Check for the following conditions:
S A poor connection or a damaged harness – Inspect
the harness for a short to ground in the sensor sig-
nal circuit. Ensure that the HO2S2 pigtail is not con-
tacting the exhaust. Check for the following condi-
tions:
S Improper mating
S Broken locks
S Improperly formed
S Damaged terminals
S Poor terminal–to–wire connection
S Damaged harness
S Intermittent test – Observe HO2S2 on the scan tool
while moving the related connections and the wiringharness with the ignition ON. If the failure is in-
duced, the HO2S2 display will change. This may
help isolate the location of the malfunction.
Test Description
Number(s) below refer to the step number(s) on the Diag-
nostic Table.
1. The On–Board Diagnostic (EOBD) System Check
prompts the technician to complete some basic
checks and store the freeze frame and failure re-
cords data on the scan tool if applicable. This
creates an electronic copy of the data taken when
the malfunction occurred. The information is then
stored on the scan tool for later reference.
2. This step determines if DTC P0140 is the result of
a hard failure or an intermittent condition.
4. Disconnecting the HO2S2 and jumpering the sen-
sor signal circuit and the sensor low circuit to
ground will determine if the ECM or wiring or
HO2S2 is malfunctioning.
6. Determines which circuit the malfunction is in. If the
sensor signal circuit and the sensor low circuit are
OK, then the ECM connection or ECM is malfunc-
tioning.
10. The replacement ECM must be reprogrammed.
Refer to the latest Techline procedure for ECM re-
programming.
DTC P0140 – Rear Heated Oxygen Sensor (HO2S2) No Activity or
Open
StepActionValue(s)YesNo
1Perform an On–Board Diagnostic (EOBD) System
Check.
Was the check performed?–Go to Step 2Go to
”On–Board
Diagnostic Sys-
tem Check”
21. Install a scan tool to the Data Link Connector
(DLC).
2. Start the engine and operate to normal operat-
ing temperature.
3. Run the engine above the specified rpm for two
minutes.
Does the scan tool display a Rear Heated Oxygen
Sensor (HO2S2) voltage between the value speci-
fied?80°C(176°F)
1200 rpm
422–478 mVGo to Step 4Go to Step 3
31. Allow the engine to idle.
2. Review the Freeze Frame data and note the
parameters.
3. Operate the vehicle within the Freeze frame
conditions and Conditions For Setting the DTC
as noted.
Does the scan tool display the HO2S2 voltage
steady around the value specified?422–478 mVGo to Step 11Go to Step 4