2004 DACIA SUPERNOVA engine

ENGINE E7J-A-2/6010
10 - 15
ENGINE AND LOWER ENGINE UNITS
RINGS
CONNECTING RODS
The horizontal play of t he connecting rod e nd: from 0.310 to 0.572
C
AUTION!
Do not use numbering punchers because of the risk of creating the be-
ginning of fissures. Use an indelible pen.
CRANKSHAFT
In c a se a re c t ifi c a tion i s m ade, t he
runner course must remain the same a long
at least 140
o out of the bearing and crankpin
circumference. These are as are de fined i n sections A
and B as shown in the adjoined scheme.
Thickness (mm):
-compression ring 1,5
-sealing ring 1,75
- oiling ring (scraper) 3
0
0
Number of beari ngs 5
Bearing diameter (mm) - nominal: 54,795 +/- 0,01
- repair: 54,550 +/- 0,005
Crankpin diameter (mm) - nominal: 43,98
-0,0 2
- repair: 43,73 -0,02
Axial play (mm) - 0,045 - 0,852 cu uzurã
- 0,045 - 0,252 fãrã uzurã
CHARASTERISTICS
vnx.su

ENGINE E7J-A-2/6010
10 - 16
ENGINE AND LOWER ENGINE UNITS
The amount of oil to be introduced in the
engine is 2.7 liters - without replacing the oi l-
filter - or 2.9 liters, after re placing the filter.
The minimum oil pre ssure at 80
o is:
-in the idle mode 1 bar
-at 4000 rot/min 3 bar
The oil pump belongs to the “gearwheel”
type. Take off the cap and a lso the clapper of
the oil-pump.
To check:
* play A (mm): - min. 0.110
- max. 0.294 * play B (mm):
-min. 0.02
- max. 0.86.
CAUTION!
P rotect the distribution and alternator belt in order to avoid water-
or cleaning substance projection on them.
OIL PUMP
* TO BE ADJUSTED TO TH E GAUGE
CH ARASTERISTICS
vnx.su

ENGINE E7J-A-2/6010
10 - 17
ENGINE AND LOWER ENGINE UNITS
DISMOUNTING AND RE-MOUNTINGTHE CYLINDER HEAD
RECO VERY ENGINE
vnx.su

ENGINE E7J-A-2/6010
10 - 18
ENGINE AND LOWER ENGINE UNITS
DIS M OUNT ING
The oil and the cooling fluid are empties.
To be taken off:
-the electric connections;
-the alterna tor and its belt;
-the pulley of the crankshaft (in order to do that, t he flywheel is bl ocked with the
MOT 582 device)
-the protection cap of t he distri bution belt RE
CO VERY ENGINE
CYLINDER HEAD
vnx.su

ENGINE E7J-A-2/6010
10 - 19
ENGINE AND LOWER ENGINE UNITS
The e ngine i s brought to t he t uning point, by aligning t he line-up mark on the crankshaft
pinion L with the fi xed marks M (the L mark i s held with the cams upwards). The screw-nut of t he stretching runne r is undone, then the belt is taken off.
(1) The stretching dire ction of the stre tcher.
RE CO VERY ENGINE
vnx.su

ENGINE E7J-A-2/6010
10 - 20
ENGINE AND LOWER ENGINE UNITS
DIS M O UNT ING
The following are to take off:-the cylinder head cap;
-the intake and exhaust collectors;
-the cylinder head screws, except the
sc rew where the centring jack is; this one
is only loosened;
-the c ylinder head is re volved round
the screw which was left in place; -the cylinder he ad is taken off;
-t he j a c ke t -m a inta i ni ng de vi c e -
MOT.484 - is mounted.
.To be mounted:
-the rocker arm ramp:
-the oil-sealing of the cam-shaft;
-the flange of the cam-shaft ;
-the pi nion of the c am-shaft , which is
blocked with MOT 799 - 01 ;
-the cam-shaft;
-the stand of t he thermostat;
-the sparking plugs;
-the springs of the valves;
-the valves;
-the oil-seals of the valves, by using the
MOT. 1335 pincers.
The cylinder head is cleaned of the fit-
ting which is left stuck to it.
It is very important not to ge t the po-
sit io nin g surface of the fittings
s cratched.
Use Decapjoint to remove t he re mains
of fittings that are left stuck. The ab ove produc t is applied on the
cleaning are a; wait ca. 10 minutes, then
clean by means of a wooden spatula.
CYLINDER
HEAD
MOT. 484
RECO VERY ENGINE
vnx.su

ENGINE E7J-A-2/6010
10 - 21
ENGINE AND LOWER ENGINE UNITS
CAU T ION!
Avoid introducing foreign bodies
into the oil grooves and tubes; you may
risk blocking up the holes of the rocker
arms and rapidly deteriorating the
cams an d the gliding parts of the
rocker-arms.
The checking of the planeness of the
cylinder he ad i s to be done with a rul er
and a set of t hickness gauges
Maximum distortion allowed: 0.05 mm.
No rectification of t he combustion he ad
is authori zed.
R
E-MOUNTING
Oil all the parts.
Mount the valve oil-seal rings no. 2 by
means of a tubular-wrench of 11 size onto
the valve guides no. 3;
Mount in the fol lowing order:
-the washers no. 1 at the base of the
valve springs;
-the new valves no. 4.
-the springs no. 5 are identical for
both intake and exhaust; -caps no. 6;
Compress springs no. 5, then m ount the
s emi-cones no. 7, which are identical for
both intake and exhaust.
CYLI NDER HEAD
CAU T ION!
They must have the same line-up
marking (8) as the old ones in order
to avoid the destruction of the valve -
stool set.
RE CO VERY ENGINE
vnx.su

ENGINE E7J-A-2/6010
10 - 22
ENGINE AND LOWER ENGINE UNITS
To mount: -camshaft annular oil seal by
means of t he MOT 1127-01 device;
-the thermostat stand.
Fo r watertight sealing, use Loctite 518.
Gir dle H must be 0.6mm up t o 1 mm
thick; it is applied in keeping with the fol-
lowing schema:
-the pinion of the cam-shaft is fixed
w ith the MOT 799-01 device, then the
thread and the end of t he scre w are oiled
and the scre w is tightened at 4.5 daNm.
CYLINDER HEAD
R
E-MO UNT ING
Oil the cam-shaft .
Mount the cam-shaft and its flange.
Check the axial play, which has to be
within 0.06 mm and 0.15 mm; in case it
does not fi t, check the flange or the cam-
shaft.
RE CO VERY ENGINE
vnx.su